Question about 1999 GMC Sierra

Open Question

What size are the bolts for the front axle flange (diff side) on a 1999 gmc seirra 4x4

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

BigBlue77
  • 59 Answers

SOURCE: 2005 Yukon Front Diff Axle seals

You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Posted on Sep 06, 2008

  • 507 Answers

SOURCE: 1990 GMC Sierra 4x4 1500

the connections near the front axle that activate the motor to engage the system aren't melted? That's a comon problem for that body style. If there good, sounds like it could be that motor itself. To figure out if it's you motor or transfercase, jack up the rear end, have a friend inside shift into 4 wheel drive, or try to, and put it in gear and apply some gas. If the front driveshaft is turning then it's something with the front end. If not, farther back in the system.

Posted on Sep 22, 2008

  • 4 Answers

SOURCE: 4x4 wont engage

i would check to see if power is going to the 4 wheel drive aculator. if there is power then your aculator is bad. it is located at the front diff.

Posted on Feb 24, 2009

  • 6982 Answers

SOURCE: 1994 c1500 4x4 front differential left side axle seal replacement

Diff does not need to be removed to change axle. If you are good at this stuff, you can figure your way through it, or get a manual as a guide (haynes etc. are OK for this stuff) Axle is held into carrier by a "c" clip so you do need to remove the cover and spider gears to get it out (not difficult) If you run into a problem, someone here will surely help!

Posted on Apr 27, 2009

  • 78 Answers

SOURCE: Remove front Brake Rotor

Try opening up the caliper with a flat screwdriver thru the opening in the middle of the housing.pry on the rotor and pull towards you to push the rotor back.That should loosen it up enough for you to get it of the rotor.If that dont work you probably got a stuck caliper and have to release the brake line and do the procedure again. GOOD LUCK

Posted on May 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm looking to replace the rear axle on my 1997 4 door 4x4 GMC Yukon 3.73 gears would a rear axle from a 1998 Yukon 4door 4x4 with 3.73 gears bolt directly to my 1997 Yukon


yes
the housings will be the same
clue here --if the diff center comes into the housing from the front not a problem
if it comes in from the rear ( tin cover removed ) replace the complete housing as you will have to have expertise in resetting the bearing pre-loads for the diff center bearings

Jul 15, 2017 | GMC Cars & Trucks

1 Answer

Can I swap a 1997 4x4 gmc front differential to a 1995 4x4 gmc


if it is the same bolt pattern in a banjo housing
(fit in from the drive shaft end not salisbury type-- remove cover and pull crown wheel out from the rear) it will fit
items to consider are axle spline size and numbers and diff ratios
if the ratios are not the same , the swap will cause very early drive line failures

Feb 08, 2016 | GMC Cars & Trucks

2 Answers

How do you pull a 1979 gmc jimmy 4x4 rear right axle


QU40221 19 Spline Outer Axle Shaft for 1977 to 1991 Chevy, GMC Corporate GM 10 Bolt Front Axle is a genuine original equipment outer axle stub shaft for all GM 10 Bolt front axles in 1977 to 1991 Chevy Blazers, GMC Jimmys, and Suburbans, plus Chevy, GMC 4x4 1/2 ton and 3/4 ton Pickups. The splined end on these new axle shafts has three snap ring grooves in three places so they are compatible with all types of automatic and manual lockout hubs plus all full-time solid splined drive gears.

Also available while supplies last: QU40221U Used Outer Axle Shaft with 3 snap ring grooves and QU40660UUsed Inner Axle Shafts with 2 snap ring grooves (QU40660U is not compatible with automatic locking hubs)



see this vdio

Apr 01, 2015 | GMC Jimmy Cars & Trucks

1 Answer

Front and back berring dissassembly of differential 2001 dodge 1500


For the rear diff., remove the driveshaft, brake drums, diff. cover, remove pinion flange nut, move diff carrier to access side gear retainer bolt and remove bolt, slide side gear pin out and push axles in to remove axle retainers and remove axels. Mark carrier bearing retainers, spin bearing retainers to loosen carrier for removal. Remove carrier, remove pinion out of diff case, then r&r bearings. Any shims should be replaced in their original location for depth and pinion to ring contact.

Feb 05, 2011 | 2001 Dodge Ram 2500 Truck

3 Answers

How to change my front differential seal and bearing ? passenger side. I bought a new wheel bearing because of a humming sound on passenger side and doing so saw leaking seal and maybe the humming was...


That will be a Huge job. The whole front diff must come out of the car and the case will need to be taken apart to even gain acess to the carrier side bearings.
The hub bearing is where the wheel bolts up is that maybe what you are talking about?
Also the axle seal isn't that bad to do you need to remove the cv shaft then it's just a simple remove the seal and install the new one.
But all of these jobs will be big ones.

Oct 13, 2009 | 1999 GMC Jimmy

2 Answers

Need instructions for removal and installation of front u-joint on 1989 gmc jimmy


buy manual, removal:  raise vehicle and place on jack stands remove skid-plate, mark relationship of driveshaft to the front diff flange and the transfer case flange, remove the bolts and straps from diff flange and trans case flange, push the rear half of the driveshaft forward far enough to separate it from the transfer case flange, then lower it and separate it at the diff flange. installation: attach the front end of the driveshaft to the front diff flange and install the straps and bolts finger tight, extend or compress the driveshaft as necessary , attach the rear end to the transfer case flange, install the straps and bolts and tighten all bolts to 59 ft #'s , install skid plates, and lower vehicle 

Sep 12, 2009 | 1992 GMC Jimmy

1 Answer

4x4 Problems


sorry lost here ,never seen one but if transmission shaft is turning to front diff then the problem is their,could be anyting from a sheared diff pinion to a broken planet wheel or possible evan a snapped half shaft or the spline on the end of the half shaft has worn and rounded off

Oct 07, 2008 | 1999 GMC Jimmy

1 Answer

Front axle how to remove half shaft


Hi.. The step to remove the front Axles of you Vitara.
Raise and support Vehicle . Remove front wheel,
Drain Diff,fluid,
Remove Locking Hub if is equipaded,
Remove Circle clip from axle shaft
On right side of Vehicle, Remove the Stabilizer Little ball joint nut. Remove castle nut Front Tie rod end,
Remove mounting bolts from brake calipper,
Remove Calipper from steering knuckle and wire a side.
Remove Stud Nut from steering knuckle,
Support Lower suspension arm with a jack,
Remove lower strut bracket bolt ,
Lower jack and disconnect Knuckle from lower suspension crontrol arm,
Pull Outler joint from Hub.
Use Large screwdriver or Prybar To pry Right inner joint from differential, The axle will go out making a little froce with the prybar,
To remove the left side,
Remove mounting bolt from inner joint flange,
Pull out axle from hub.

To reinstall just reverse the prosses.

I hope this help on your job...
Thank you for use fixya....


Aug 18, 2008 | 1999 Suzuki Vitara

Not finding what you are looking for?
1999 GMC Sierra Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...