Question about 1999 Dodge Intrepid

1 Answer

Do you have to remove the oil coolant lines to the radiator to change the water pump and timing belt?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,102 Answers

You shouldn't have to.

Posted on Dec 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the water pump on a ford festiva 1995


Drain all the coolant.Jack up the car on the front passenger side.Remove the passenger side wheel.Put a jack under the oil pan.Detach the engine mounts on the passenger side of the car.Remove all external belts.Remove the upper timing belt cover boltsLower the engine using the jack.Remove the water pump pulley. (3 bolts)Remove the upper timing belt cover.Disconnect the coolant line running across the front of the engine from the water pump. (2 bolts on a flange)Pull the timing belt.Pull the water pump.Installation is just reversed.

Jun 07, 2012 | Cars & Trucks

1 Answer

How do i change the water pump belt on a 2001 Cadillac Deville .


2001 Cadillac Deville 4.6L SFI DOHC 8cyl Removal & Installation procedure...

1. Before servicing the vehicle, refer to the Precautions section.
2. Drain the coolant.
3. Remove or disconnect the following:
Negative battery cable
Upper fill panel, if equipped
AIR injection control valve, if equipped
Air cleaner
Oil level indicator tube nut, if necessary
Water pump belt cover
Water pump drive belt
Lower radiator hose
Thermostat bypass hose from the coolant inlet housing
Water pump cover

4. Remove the water pump by rotating it clockwise using special Tool J 38816-1A (water pump remover/installer).

To install:

1. Install the water pump with a new O-ring, by turning it counterclockwise using the special tool, until it stops. Torque the water pump to 73 ft. lbs. (100 Nm).

  1. zjlimited_842.jpg

Fig. To ensure proper operation, be sure to install a new O-ring (click for zoom)

2. Install or connect the following:
Water pump cover. Torque the bolts to 89 inch lbs. (10 Nm).
Lower radiator hose
Thermostat bypass hose to the coolant inlet housing
Water pump drive belt
Water pump belt cover
Oil level indicator tube nut, if necessary
Air cleaner
AIR injection control valve, if equipped
Upper fill panel, if equipped
Negative battery cable

3. Refill and bleed the cooling system.
4. Run the engine and check for leaks.


Hope this helps (remember to rate this comments)

Mar 10, 2011 | 2001 Cadillac DeVille

1 Answer

How do i replace the water pump on a 1997 rodeo v6?


YOU HAVE TO REMOVE TIMING BELT AND IDLER PULLEY.YOU NEED TO REPLACE TIMING BELT WHEN YOU REPLACE WATER PUMP.TO REPLACE WATER PUMP. DRAIN COOLANT SYSTEM.REMOVE UPPER RADIATOR HOSE.REMOVE TIMING BELT AND IDLER PULLEY.UNBOLT AND REMOVE THE WATER PUMP.CLEAN ANY GASKET MATERIAL OR SEALANT RESIDUE FROM THE WATER PUMP MATING SEALING SURFACES.WHEN INSTALLING NEW WATER PUMP BESURE TO USE A SEALANT ON BOTH SIDES OF WATER PUMP GASKET TO KEEP IT FROM LEAKING COOLANT.TORQUE WATER PUMP BOLTS TO 13 FT LBS IN A TWO STEP CRISSCROSS SEQUENCE.INSTALL THE IDLER PULLEY.TIGHTEN THE MOUNTING BOLT TO 31 FT LBS.INSTALL AND TENSION THE TIMING BELT.INSTALL THE UPPER RADIATOR HOSE.REFILL BLEED THE COOLANT SYSTEM.

Feb 19, 2011 | 1997 Isuzu Rodeo

1 Answer

How to replace a radiator on a1994 toyota land cruiser


dak408_129.gif

  1. Disconnect battery ground cable.
  2. Drain engine coolant.
  3. Remove battery and tray,
  4. Remove radiator grille
  5. Disconnect No. 3 water bypass hose.
  6. Disconnect radiator inlet hose.
  7. Disconnect coolant reservoir hose.
  8. Loosen water pump pulley mounting bolts.
  9. Loosen lock, pivot and adjusting bolts of alternator and remove drive belts.
  10. Disconnect oil cooler hose from clamp on fan shroud, then remove shroud.
  11. Remove water pump pulley mounting nuts.
  12. Remove fan with fluid coupling, water pump pulley and fan shroud.
  13. Disconnect transmission oil cooler hoses.
  14. Disconnect radiator outlet hose.
  15. Remove radiator brackets, then the radiator.
  16. Reverse procedure to install.

Dec 11, 2010 | 1994 Toyota Land Cruiser

2 Answers

Replacing waterpump in1999 nissan pathfinder


Water Pump Removal & Installation To Remove:
  1. Allow the engine to cool and drain the coolant from the radiator and both engine block plugs.
  2. Remove the fan shroud and both radiator hoses.
  3. Remove the drive belts.
  4. Remove the water pump pulley.
  5. Remove the crankshaft pulley.
  6. Remove the timing belt covers.
  7. Remove the water pump.
Water pump removal/installation 7924vg20.gif

To Install:
  1. Install the water pump with new gasket.
  2. Install the timing belt covers.
  3. Install the crankshaft pulley.
  4. Install the water pump pulley.
  5. Install the drive belts and fan shroud.
  6. Install the radiator hoses.
  7. Install the coolant drain plugs.
  8. Refill the cooling system.
prev.gif next.gif

Aug 10, 2010 | 1997 Nissan Pathfinder

1 Answer

How do I remove oil pump on 2000 Plymouth voyger


The oil pump removal procedure for Plymouth Voyager 2000.
A oil pump is usually located in the oil pan. If you want to change the oil pump and replace it with a new one, roll up your sleeves and get ready for some dirty work.
The procedure to remove oil pump is as follows:--
  • Drive your vehicle up onto ramps or lifts so you have room to work as you pull out the oil pump. You could also use a jack, but make sure you brace the front wheels so they don't roll. In addition, set the emergency break firmly into position so the car doesn't roll.
  • Remove the engine front cover then drain the engine oil and take out the oil pan. It is under the engine and looks like the bottom of the motor.
  • Unscrew the oil pump mounting bolts with a wrench and proceed to remove the oil pump itself by pulling it down and out of the engine. Avoid getting any contaminants into the oil pump assembly while removing.
The Water pump removal procedure for Plymouth Voyager 2000.
The water pump is the heart of the Plymouth Voyager's cooling system, circulating the coolant. When the water pump is faulty, it can cause serious damage to the engine of your Plymouth Voyager.
  • Disconnect the negative battery cable.Place a drain pan underneath the radiator. When the engine is cool, drain the cooling system from the radiator into the pan.
  • Remove the right inner splash shield and the accessory drive belts. Support the engine underneath and remove the right motor mount with the bracket.
  • Take off the front cover and remove the timing belt along with the timing belt idler pulley. Also remove the camshaft sprockets, the rear cover to the timing belt and the alternator with its bracket.
  • Loosen and remove the bolts to the water pump and remove it from the engine.Install the new water pump after inserting a new o-ring gasket. Tighten the bolts to 105-inch lbs. Make sure that the pump can move freely by rotating it by hand.
  • Replace all components in reverse order. Tighten the camshaft sprocket bolts to 75 foot pounds and the timing belt idler pulley to 45 foot pounds.
  • Refill the cooling system with coolant and reconnect the negative battery cable. Start the engine and check for leaks when it reaches normal operating temperatures.

Loud noises coming from the cooling system could be a sign that your water pump needs replacing. A leak in the coolant may also be an indicator. You can expect that a water pump will need to be changed every 70 to 100 thousand miles or so in a Plymouth Voyager vehicle.
Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Jun 13, 2010 | 2000 Plymouth Voyager

1 Answer

Need to change the water pump.


Mitsubishi Galant/Mirage/Diamante 1990-2000
Water Pump - REMOVAL & INSTALLATION

1.5L and 1.8L Engine

1217db1.jpg



Fig. Water pump and related components-Mirage with 1.5L (4G15) engine

c341f23.jpg

Fig. Water pump and related components-Mirage with 1.8L (4G93) engines
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.

CAUTION Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Remove the engine undercover.
  2. Disconnect the clamp bolt from the power steering hose.
  3. Remove the engine drive belts.
  4. Support the engine with the appropriate equipment and remove the engine mount bracket.
  5. Remove the timing belt. Refer to the timing belt procedure in this section.
  6. Remove the power steering pump bracket.
  7. Remove the alternator brace.
NOTE The water pump mounting bolts are different in length, note their positioning for reassembly.
  1. Remove the water pump, gasket and O-ring where the water inlet pipe(s) joins the pump.
To install:
  1. Thoroughly clean both gasket surfaces of the water pump and block.
  2. For 1.5L engines, install a new O-ring into the groove on the front end of the water inlet pipe. Do not apply oils or grease to the O-ring. Wet the O-ring with water only.
  3. For 1.8L engines, apply a 0.09-0.12 in. (2.5-3.0mm) continuous bead of sealant to water pump and install the pump assembly. Install the water pump within 15 minutes of the application of the sealant. Wait 1 hour after installation of the water pump to refill the cooling system or start the engine.
  4. Install the gasket and pump assembly and tighten the bolts to 17 ft. lbs. (24 Nm). Use care when aligning the water pump with the water inlet pipe.
  5. Install the remaining components in the reverse order of removal.
  6. Fill the system with coolant.
  7. Connect the negative battery cable, run the vehicle until the thermostat opens and fill the radiator completely.
  8. Once the vehicle has cooled, recheck the coolant level.

1.6L and 2.0L (SOHC and DOHC) Engines

bfcd21c.jpg

Fig. Water pump mounting-2.0L DOHC engine shown
  1. Disconnect the negative battery cable.
  2. Drain the engine coolant.

CAUTION Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Remove the timing belt. Refer to the timing belt procedure in this section.
  2. If necessary, remove the alternator brace from the water pump.
  3. If necessary, remove the timing belt rear cover.
  4. Remove the water pump mounting bolts.
  5. Remove the water pump, gasket and O-ring.
To install:
  1. Install a new O-ring on the water inlet pipe. Coat the O-ring with water or coolant. Do not allow oil or other grease to contact the O-ring.
  2. Use a new gasket and install the water pump to the engine block. Torque the mounting bolts to 8.7-11 ft. lbs. (12-15 Nm). Install the alternator brace on the water pump. Torque the brace pivot bolt to 17 ft. lbs. (24 Nm).
  3. If removed, install the timing belt rear cover.
  4. Install the timing belt. Refer to the timing belt procedure in this section.
  5. Install the remaining components.
  6. Refill the engine with coolant.
  7. Connect the negative battery cable, start the engine and check for leaks.

I really hope this help (remember rated this help).

Mar 26, 2010 | Mitsubishi Diamante Cars & Trucks

2 Answers

Changing a water pump on a 1981 ford f100 pick-up


Ford Pick-Ups/Bronco 1976-1986 Repair Guide Water Pump - REMOVAL & INSTALLATION

6-300 Engines
  1. Drain the cooling system.
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Disconnect the lower radiator hose from the water pump.
  2. Remove the drive belt, fan, fan spacer, fan shroud, if so equipped, and water pump pulley.
  3. Remove the alternator pivot arm from the pump.
  4. Disconnect the heater hose at the water pump.
  5. Remove the water pump.
  6. Before installing the old water pump, clean the gasket mounting surfaces on the pump and on the cylinder block. If a new water pump is being installed, remove the heater hose fitting from the old pump and install it on the new one. Coat the new gaskets with sealer on both sides and install the water pump in the reverse order of removal. Torque the mounting bolts to 14-18 ft. lbs.

V6-3.8L Engines
See Figures 1 and 2

5ee356b.jpg

Fig. 1: V6 water pump installation

e5820a7.jpg

Fig. 2: V6 water pump bolt torque sequence
  1. Drain the cooling system.
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Remove the air cleaner.
  2. Remove the bolts securing the fan shroud to the radiator, if so equipped, and position the shroud over the fan.
  3. Disconnect the lower radiator hose, heater hose and by-pass hose at the water pump. Remove the drive belts, fan, fan spacer and pulley. Remove the fan shroud, if so equipped.
  4. Loosen the alternator pivot bolt and the bolt attaching the alternator adjusting arm to the water pump. Remove the power steering pump bracket from the water pump and position it out of the way.
  5. If necessary, remove the air conditioner compressor and bracket. The refrigerant lines should remain connected.
  6. Remove the bolts securing the water pump to the timing chain cover and remove the water pump.
  7. Thoroughly clean the mounting surfaces of all gasket material.
  8. Install the water pump in the reverse order of removal, using a new gasket. Torque the bolts to 15-22 ft. lbs. in the sequence shown.


8-360, 390
  1. Drain the cooling system.
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Remove the bolts securing the fan shroud to the radiator, if so equipped, and position the shroud over the fan.
  2. Disconnect the lower radiator hose, heater hose and by-pass hose at the water pump. Remove the drive belts, fan, fan spacer and pulley. Remove the fan shroud, if so equipped.
  3. Loosen the alternator pivot bolt and the bolt attaching the alternator adjusting arm to the water pump. Remove the power steering pump bracket from the water pump and position it out of the way.
  4. If necessary, remove the air conditioner compressor and bracket. The refrigerant lines should remain connected.
  5. Remove the bolts securing the water pump to the timing chain cover and remove the water pump.
  6. Install the water pump in the reverse order of removal, using a new gasket. Torque the bolts to 20-25 ft. lbs.

8-351M, 400, 460
  1. Disconnect the battery ground.
  2. Drain the cooling system.
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Remove the bolts securing the fan shroud to the radiator, if so equipped, and position the shroud over the fan.
  2. Remove the fan assembly.
  3. Remove the fan shroud.
  4. Remove the accessory drive belts and water pump pulley.
  5. Remove the alternator and brackets.
  6. Remove the compressor and bracket and lay it aside. DO NOT disconnect the refrigerant lines!
  7. Remove the power steering pump and brackets. Lay it aside. DO NOT disconnect the fluid lines!
  8. Disconnect the heater hose and lower radiator hose from the pump.
  9. Remove the bolts securing the water pump to the engine and lift off the water pump.
  10. Clean all gasket mounting surfaces thoroughly.
To install:
  1. Install the water pump in the reverse order of removal, using a new gasket coated with sealer. Torque the bolts to 12-18 ft. lbs.
  2. Install all remaining parts in reverse order. Fill the cooling system, start the engine and check for leaks.

continue...

Mar 25, 2010 | 1981 Ford F 100

1 Answer

Removal and installation of the water pump


3.0L or 3.8L engine?

please rate as fixed if this solves your issue.

Section 03-01B: Engine, 3.8L 1996 Windstar Workshop Manual
IN-VEHICLE SERVICE Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fuel Line Disconnect Tool Set T90T-9550-S
Removal
  1. Drain engine cooling system. Refer to Section 03-03 .
  1. Loosen drive belt tensioner (6B209) and remove drive belt (8620). Refer to Section 03-05 .
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Disconnect lower radiator hose (8286) from radiator lower hose tube (8291) and radiator (8005).
  1. Disconnect radiator lower hose tube from water pump (8501).
  1. Remove lower nut on both front engine support insulators (6038).
  1. Lower vehicle.
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove generator (GEN) (10346) from power steering pump support (3C511).
  1. Position drain pan and disconnect power steering pressure line from power steering pump (3A674) using Fuel Line Disconnect Tool Set T90T-9550-S.
  1. Remove power steering reservoir filler cap.
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If using a prying device to assist in water pump removal, be careful not to damage the mating surfaces.
    Disconnect water bypass hose (8597) and oil cooler hose (6B850) from heater water outlet tube (18663).
  1. Remove retaining bolts and disconnect heater water outlet tube from water pump.
  1. Remove A/C bracket brace.
  1. Attach engine lifting eye to left-hand (front) exhaust manifold (9430).
  1. Attach lifting equipment to engine lifting eye and raise front of engine approximately 51 mm (2.0 inches) to provide necessary clearance for water pump removal.
  1. Remove water pump pulley retaining bolts and water pump pulley (8509).
  1. Remove drive belt tensioner pulley retaining bolt and drive belt tensioner pulley (6B217) from power steering pump support.
  1. Remove power steering pump support retaining bolts and nut. Place power steering pump and support assembly aside in a position to prevent fluid leakage.
  1. Remove water pump retaining bolts and nuts and water pump. Discard used water pump housing gasket (8507).
Installation
  1. NOTE: Lightly oil all bolt and stud bolt threads before installation except those specifying special sealant.

    Clean gasket surfaces on water pump and engine front cover (6019).
  1. NOTE: The threads of the No. 1 engine front cover retaining stud must be coated with Pipe Sealant with Teflon® D8AZ-19554-A or equivalent meeting Ford specification WSK-M2G350-A2 before installing.

    NOTE: Gasket and Trim Adhesive D7AZ-19B508-B or equivalent meeting Ford specification ESE-M2G52-A is recommended to hold the water pump housing gasket in position.

    Position a new water pump housing gasket on water pump housing sealing surface.
  1. Position water pump on the engine front cover. Install retaining bolts.
  1. Position power steering pump support and install retaining nuts and bolts. Tighten bolts and nuts to 40-55 Nm (30-40 lb-ft).
  1. Install drive belt tensioner pulley and retaining bolt. Tighten bolt to 70-95 Nm (52-70 lb-ft).
  1. Install A/C bracket brace.
  1. Position water pump pulley on water pump hub and install retaining bolts. Tighten bolts to 8.0-11.5 Nm (71-101 lb-in).
  1. Lower engine and disconnect lifting equipment from lifting eye.
  1. Remove lifting eye from exhaust manifold.
  1. Connect heater water outlet tube to water pump and install retaining bolts. Tighten bolts to 8-11.5 Nm (71-101 lb-in).
  1. Connect water bypass hose and oil cooler hose to heater water outlet tube. Tighten clamps securely.
  1. Connect power steering pressure line to power steering pump fitting.
  1. Install power steering reservoir filler cap.
  1. Install generator to power steering pump support. Refer to Section 14-02 .
  1. Connect battery ground cable. Refer to Section 14-01 .
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Install lower nut on front engine support insulators and tighten retaining nut to 88-119 Nm (65-87 lb-ft). Install lower nut of rear engine support insulator and tighten to 77-104 Nm (56-76 lb-ft).
  1. Connect radiator lower hose tube to water pump. Install retaining bolt and tighten securely.
  1. Connect lower radiator hose to radiator lower hose tube and radiator. Position hose clamps securely. Refer to Section 03-03 .
  1. Lower vehicle.
  1. Position drive belt over drive belt tensioner and release drive belt tensioner. Refer to Section 03-05 .
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: This engine has aluminum cylinder heads (6049) and requires a special corrosion inhibiting coolant to avoid cooling system damage. Refer to Section 03-03 for the coolant specifications.
    Fill and bleed cooling system with specified coolant.
  1. Fill power steering pump reservoir with specified fluid.
  1. Start engine and check for coolant and power steering fluid leaks. Service as necessary.


    Water Pump
581f50d.gif

Apr 13, 2009 | 1996 Ford Windstar

3 Answers

Replacing water pump on a dogge Caravan 1996


Alright, here's a pic of the mechanicals:
0900c1528006619e.jpg


The bad news is on your vechile you have to remove the timing belt, but here's a step by step.
  1. Disconnect the negative battery cable.
  2. Remove the drive belts.
  3. Drain the cooling system.
CAUTION When draining coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Remove the timing case cover and timing belt. Refer to Timing Belt Covers and Timing Belt Removal procedures.
  2. Remove the pump assembly mounting bolts.
  3. Separate the pump assembly from water pipe and remove.
  4. Clean gasket and O-ring mounting surfaces.
  5. Install a new O-ring on water pipe and lubricate with water.
  6. Install a new gasket on pump body.
  7. Press the water pump assembly into water pipe.
  8. Install pump mounting bolts and tighten to 27 Nm (20 ft. lbs.).
  9. Install timing belt and cover. Refer to Timing Belt procedures.
  10. Install drive belts.
  11. Fill the cooling system
To remove timing:
0900c152800661ff.jpg
The timing belt can be inspected by removing the upper (front outer) timing cover.
  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belts.
  3. Remove the timing belt covers.
  4. Identify the timing belt running direction to avoid reversal during installation.
  5. Loosen timing belt tensioner bolt and remove timing belt.
  6. Remove the crankshaft sprocket flange.
To install:
  1. Rotate the crankshaft sprocket until timing mark on crankshaft sprocket is lined up with the oil pump timing mark at 1 o'clock position.
  2. Rotate the (inner) camshaft sprocket until mark on (inner) camshaft sprocket is lined up with the timing mark on alternator bracket.
  3. Rotate the (outer) camshaft sprocket (radiator side) until mark on the sprocket is lined up with the timing mark on the timing belt inner cover. Refer to timing belt illustration.
  4. Install the timing belt on the crankshaft sprocket while maintaining pressure on the tensioner side.
  5. Position the timing belt over the camshaft sprocket (radiator side). Next, position the belt under the water pump pulley, then over the (inner) sprocket and finally over the tensioner.
  6. Apply rotating force in the opposite direction to the camshaft sprocket (radiator side) to create tension on the timing belt tension side.
  7. Rotate the crankshaft in a clockwise direction and recheck engine timing marks.
  8. Install the crankshaft sprocket flange.
  9. Loosen the tensioner bolt and allow tensioner spring to tension the belt.
  10. Again rotate the crankshaft in a clockwise direction (2) full turns. Recheck the engine timing. Tighten the tensioner bolt to 23 ft. lbs. (31 Nm).
  11. Install the timing covers.
  12. Install the accessory drive belts.
  13. Connect battery negative cable.
Hope this helps.

Jun 27, 2008 | 1996 Dodge Caravan

Not finding what you are looking for?
1999 Dodge Intrepid Logo

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...