Question about 1989 GMC Suburban

1 Answer

How to properly remove door panels on my 1989 gmc suburban

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • GMC Master
  • 680 Answers

Remove the window crank handle (by removing the clip...assuming that it's a manual window). Remove the screws in the arm rest. Depending on the options (full panel, half panel, choo choo custom, etc...) the screws half-way down the door (standard package) the one up by the vent window, and carefully pop the clips along the front, back, and bottom. Lift to remove from the window edge and remove.

Posted on Dec 29, 2010

  • Drew Z
    Drew Z Dec 29, 2010

    If at all possible, please rate my answer and leave a testimonial.

×

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1986 Answers

SOURCE: 1986 gmc suburban door panel removal

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 468 Answers

SOURCE: Removing fuel pump from 1989 gmc suburban?

You'll have to take the fuel tank off, so make sure you have something to support it, while loosening the tank straps. Lower it down far enough to disconnect the sender and pump wires, and the fuel line. Drag the tank out where you can work on it, and you can carefully use a hammer and screwdriver and chisel to tap on the lock ring until it rotates the 1/4 turn it needs to come off. Remove, and replace it with the new one. While you have it open, it's easier to empty it out into gas cans so it's easier to put back up. You may want to put a light coating of a silicone based lubricant on the o-ring when you put the new pump in. After that's done, just make sure that you hook everything back up the way you found it, and put gas back in it, and you're done.

Posted on Oct 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1989 suburban front bumper


Sara, 1989 GMC Suburban front bumper removal. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How To Install Replace Bent Rusted Front Bumper 1989 99 Chevy GMC Pickup...
Grille Replacement 88 98 Chevy trucks
1989 Chevrolet R1500 Suburban Parts NationalGMParts com

Jul 10, 2016 | 1989 GMC Suburban

1 Answer

Replacing Exterior Door Handle on 1989 burb


if you can not get to the handle at all you will need to go from the inside. if that is the case try and pry the top of the door panel off without distorting the panel. then with a flash light look down inside the door and you should see a metal rod, try pulling the rod up or down which should open the door! hope this helps

Feb 22, 2014 | GMC Cars & Trucks

1 Answer

1989 GMC Suburban speedomeeter


would imagine the internal speedo gears are skipping when cold. They are located in the transmission where the cable goes into. It is easily removed to inspect

Mar 27, 2010 | 1989 GMC Suburban

1 Answer

Replacing WINDOW REGULATOR, on 92 gmc suburban, can I pull the regulator and motor out through one of the holes or do I need to remove the door enter metal panel ?


Proper proceedure in service manual is to pull whole panel. But, I have been able to remve top half of bolts on panel, put a piece of wood (like a small 2X4) between door and panel and remove regulator. hope that helps.

Mar 02, 2010 | 1992 GMC Suburban

1 Answer

1999 chevrolet suburban: door panel removal


hello here is the instructions for removing the door panel.

  • Remove the door handle bezel.
  • Remove the window handle,.
  • Remove the power accessory switch panel.
  • Remove the trim panel upper extension
  • Remove the trim panel screws.




  • Remove the courtesy light,
  • Remove door panel screws.
  • Remove the trim panel from the door, carefully sliding the trim panel up to release the retainers from the door.
  • Remove the speaker wire.
  • 3470484.gif

    Jan 23, 2010 | 1999 GMC Suburban

    1 Answer

    Drivers Side Door Handle


    You need to take inside door panel off This just clips on but there are screws in armrest and inside door handle look for any other small square covers that may hide screws Lift panel up Make sure window is up Disconnect wiring from panel and you can now get at door handle linkage and bolts

    Jul 10, 2009 | 1989 GMC S-15 Jimmy

    1 Answer

    I have a 1996 gmc suburban - the front pass door will not open from inside, you can open from outside. How can i replace a broken handle/latch?


    Either a piece broke or the pullrod came off. Either way... you'll have to remove the interior door panel to repair.

    Jun 10, 2009 | 1996 GMC Suburban

    1 Answer

    1986 gmc suburban door panel removal


    You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

    Mar 25, 2009 | 1986 GMC Suburban

    1 Answer

    What kind of transmission is in my 2wd 1989 suburban


    In the 89 model the 1/2 tons came with the R700(4L60)
    and the 3/4 tons came with the T400 (3L80)

    Please rate this fixya



    Jan 26, 2009 | 1989 GMC Suburban

    2 Answers

    1999 GMC Suburban - how to install dr side power window motor/arm


    The window should be put in a closed position.
    Hidden screws behind buttons of the same color as panel should be opened up using a pick or small screwdiver.
    Pry the lower part of the panel away from the door using a paint scraper, The lower half of this panel is usually held in with plastic fastners. When pulled hard enough they will release. These fastners are replacable you can buy them at your local body shop. After releasing all plastic fastners lift door panel off door lock in an upward thrust. Be careful not to pull to far away from door due to wire harnesses and speaker wires ect.. These can be uncliped to remkove whole panel. To operate window you can replug window harness wires in order to bring the window into the proper position to remove bolts that hold it into place. Carefully position glass in upward position and duct tape in place.
    The regulator is held in place by three or more bolts.
    Remove regulator.
    Compare your new part to the existing window regulator.
    Installation is reversal of removal.
    Any questions get back!

    Jan 17, 2009 | 1999 GMC Suburban

    Not finding what you are looking for?
    Cars & Trucks Logo

    309 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top GMC Experts

    yadayada
    yadayada

    Level 3 Expert

    76132 Answers

    Freddy

    Level 3 Expert

    1311 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Are you a GMC Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...