Question about 2000 Renault 181

2 Answers

Clio My key fob wont work - i have had a new battery put in this morning and when i press key to open door the red indicator light on the fob works but it doesn't lock or unlock my doors

Posted by on

  • 1 more comment 
  • Anonymous Mar 17, 2014

    2010 dodge journey fob wont lock/unlock doors

  • Anonymous Mar 23, 2014

    the red function light on one of the TS001 key fobs remains on constantly until the battery is drained flat. all other locking and keyless start functions work.

  • Anonymous Mar 29, 2014

    no lock for the key and doe,nt lock when locking doors

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 54 Answers

The key has lost its code. open the doors manually and use the central locking button inside the car. hold it down and keep pressing your key fob. this should re code the key

Posted on Jul 12, 2008

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

Hi, have a Renault Megane car, trip computer says replace car batteries, did this but message never went away it stayed on the trip computer. Had car serviced and asked them to check my key card, staff said my card was faulty even though it works perfectly well apart from message on trip computer asking me to change battery? Also staff said my spear card would go the same war as I have never used it, I was keeping it safe for emergency use, staff said eventually both cards will de-program. Is this information correct?
Many thanks.
Noel Ivers

Posted on Aug 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key fob wont re set on my ssan yan rexton


I recently changed the battery on my key fob for my ssanyong rexton. I then did the following for the key fob to make it work. 1. Enter vehicle and close all doors.

2. Put seatbelt on (or clip it into the buckle) to shut the warning buzzer off.

3. Put key in ignition, turn to run position but don't start it.

4. Press and hold both buttons on key fob until red light on fob stays on. Then let go of both buttons. Then pressed the alarm button then the panic button, somthing like that. To be fair the button sequence after the red light came on is a bit vague. The alarm was blaring so i was happy when it just stopped.

May 23, 2012 | SsangYong Rexton Cars & Trucks

1 Answer

Central locking wiring clio


I had a problem where my key fob did not lock or unlock the car, Renault Clio Dynamique, but the central locking button in the car did still work and engine turned over fine. Changed the key fob battery still nothing. Read online about disconnecting and reconnecting the car battery, (negative only) and hey presto it worked! All working fine now!

May 13, 2012 | 2002 Renault Clio

1 Answer

My renault clio 1998 r reg key fob wont work


hold the cetral locking lock all button down until the doors lock and unlock. The imobilser light goes solid red. At this point you have 10 to press the botton on your key 2 times . the doors will unlock and lock.

Mar 27, 2012 | Cars & Trucks

1 Answer

Keyless entry remote wont progam


It will not unlock the door the first time you push the button. This only registers the key fob ID into the computer. When you press the button on the key fob, press it only once and wait for the hazzard lights to flash twice again. Then open the driver's door. The key fob will not become active until you open the driver's door.

If your hazzard lights do not flash after you press the button on the key fob, there is most likely a problem with the key fob. Either it is not the correct key fob for your vehicle, or the battery is not in correctly or the key fob is defective.

The only other advice I can give you is to have it programmed with a scan tool. This way, the scan tool can verify that the computer in your vehicle is receiving the signal from the key fob.

It can be done either way, but if the "no scanner" way does not work, the rest of the system should be checked for possible problems.

Dec 12, 2011 | 2005 Nissan Altima

1 Answer

Sorry my car was not listed so picked Altima 2003 Micra Intelligent key fob not working properly. Can drive the car but cannot open or lock the doors. Did get fob wet. Now dried out. Worked for first few...


You are going to need to check the power lock control moduel on the inside of the door panel. If the FOB appears to be working but the doors are not unlocking, you need to check this. I would also replace all fuses that control the locks. If both of these devices check out ok, you may need to replace your FOB. To check your power lock control moduel, manually lock and unlock your doors by pressing the lock button on the inside of the door. If it does not work, it is either the fuses or the power lock control moduel. If it works, your FOB has gone bad. Hope this helps! Please rate 4 thumbs up!

Apr 18, 2011 | Nissan Altima Cars & Trucks

2 Answers

Central locking doesnt work on mk2 clio t reg


try putting the key in the ignition and turning it to on then holding the unlock button for 30 seconds and then remove the key and try the remote if still no good go to your dealer and get them to reinishalise the system

Sep 29, 2009 | Renault Sportwagon Cars & Trucks

1 Answer

Renault key fob doesnt work


Hi.
I have a clio II, 2001, i have the same problem and i fixed it.
Don't know if will work for you but here it goes:

1 - no key in ingnition
2 - press the unlock button in console off the car for about 10 seconds(dont let go)
3 - it should work the central doors one time and then 2 times( hear)
4 - press the remote a few times until it starts working

It worked for me hope the same for you.
Please tell me if it worked and pass the message.

Good luck

Sep 13, 2009 | 2000 Renault 181

1 Answer

SAME PROBLEM, replaced battery in both fobs....


the keys needs to be initialised. put key in door lock or ignition barrel and press/hold the remote open button until led flashes on dash, release button and rremove key from lock, remote should now work

Aug 30, 2009 | 1999 Porsche Boxster

2 Answers

Key fob lights up but doesn't work even with a new battery


I'm more familiar with Range Rovers and Saab's when it comes to key fobs but if you changed the battery you have to re-program the key fob. If you do not have an owner's manual that can take you through the steps you might want to try: push and hold the lock button on the key fob, put it in the driver's side door and turn to lock. With the button still depressed turn back to open, remove the key and release the button. If this doesn't work check any and all fuses associated with your system and last but not least you could take it to a dealer. Good luck!

Aug 25, 2009 | 2000 Renault 181

1 Answer

HELP HELP !!!!!!! Electric fault i think !!!!!!!!!!


1....ensure the battery in the "Key Fob" is OK............Press either Lock or Unlock button for more than 1 second, the lamp on the fob will light if OK. Change battery if it does not illuminate! 2.....if battery on fob OK.......Re Syncronise the key fob to the car by:.... a brief press on either button twice and within 30 seconds turn Key to position 2 on the ignition lock
Hope that fixes it...let me know?

Nov 09, 2008 | 1998 Mercedes-Benz C-Class

Not finding what you are looking for?
Cars & Trucks Logo

1,563 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

xxxxxx xxx

Level 3 Expert

4706 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...