Question about 1994 Jeep Grand Cherokee

1 Answer

I took my 1994 Jeep Grand Cherokee Laredo to the Technician for a tune-up. He put new parts Brake Pads, Brake Shoes. Even I bought four new tires. Now my vehicle doesn't stop at all. The brake pedal goes to the bottom and there it stop. The pedal doesn't seems to have power. The ABS system was taken out too because it doesn't work since two years ago. The brakes were bleeded so many times that more than five large brake fluid cans has been wasted. Now it still not working and the technician doesn't know what else could it be. Any idea?

Posted by Anonymous on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 677 Answers

Sounds like the master cylinder is full of air.Somebody let it run dry when doing a pad change.(maybe)Did the calipers get rebuilt or were the pistons just pushed back in?
Brakes are a sealed unit.If there is no leaks,then you must start at the 1st point of operation.The master system.Hope this helps.

Posted on Dec 30, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to change transfer case control module on 2006 jeep grand cherokee

I have a 2006 grand cherokee laredo 4x4. I have only had it in four wheel drive once, and thats when i bought it. Yesterday I was just testing it out. Put it in neutral,foot on brake, Pulled up on the the leaver and nothing happened, except a service light came on. Saying"service transfer case". No matter what I tried I could not get it to work. What say you.

Jun 27, 2013 | Cars & Trucks

1 Answer

Remove rear brakes from 2006 jeep grand cherokee laredo

its very easy. Pull tires off after putting vehicle on jack stands. There are only 2 bolts that holt the caliper on the rotor. Once you remove those bolts, the caliper will slide off. the break pad removal can be a little tricky, as you must depress a button with a screw driver in order to get he pads out. I recommend having two people to do this part. Once the old pads are out, us either a c-clamp or a pair of chanel locks to push the piston back in. Once the piston is back in, insert the new pads, place the caliper back on the rotor and reinsert the two bolts. I dont know the specs of the bolts, but be sure not to tighten them too much as you can damage parts to the brake system. It literally took me 20 minutes to do my brakes.

Aug 03, 2010 | 2006 Jeep Grand Cherokee

1 Answer

How do I tune up a jeep grand cherokee laredo?

change the cap rotor plugs and wires maybe even the fuel filter

Apr 20, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Parking brake for a 96 Jeep Grand Cherokee Laredo

A Haynes or Chilton manual should have all the proper pictures and instructions for reassembly.

Mar 29, 2010 | 1996 Jeep Grand Cherokee

1 Answer

'96 Jeep Grand Cherokee parking break doesn't work

check the rear brakes. Possible they are out of adjustment or worn shoes.

Nov 13, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Parkling Brake Console Light Stays On

Parking Brake Console Light Stays On The light is on because the brake fluid is low. The sensor in the brake fluid reservoir is signaling low fluid. This may be because leaking or the brake pads/shoes are worn down, so check to see if they needs replacement. In the mean time you can add brake fluid.

The Parking brake switch is activated by the brake handle. If you use a flashlight you may be able to see it next to the handle.

May 31, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Brake pads specifications

I just searched google and looked at JC Whitney. They have brake parts and ship internationally. (don't know cost) But it's worth looking into!

Apr 30, 2009 | 2001 Jeep Grand Cherokee

5 Answers

94 jeep grand cherokee laredo brake problem

Hi there!

Check for leaks at the slave cylinders and flexi hoses.

After several attempts of losing pressure - check the brake fluid level in the master.

If you arn't losing any fluid, You've got a damaged seal in the Master cylinder, or are drawing air in due to improper adjustment (excess travel) of slave cylinders.

Are you trying this with engine running? - How does this affect it (using servo assist)

Jun 15, 2008 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides