Question about Chevrolet Silverado 1500

Open Question

How to adjust headlights on a 2008 silverado 1500, I see the white screw on top but shouldnt there be 2 screws?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: headlight adjustment 2000 Alero

There should be 2 more screws on the headlight housing, on each housing there is one towards the middle and one towards the fender, try adjusting the one that you haven't already

Posted on Mar 08, 2009

tepfy
  • 319 Answers

SOURCE: headlight removal 1993 ford f150

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800c1846

enter your info pick the part and go to fix it your self.

tepfy

Posted on Feb 01, 2009

  • 1986 Answers

SOURCE: Can't find headlight adjustment screws

They nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.


Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Posted on Sep 17, 2009

Testimonial: "The adjustment screw (for passenger side) is located between the battery & frame's second hole. Turning counter-clockwise, it adjusts downwards,Thanks"

  • 1986 Answers

SOURCE: 1998 Ford Mustang Headlight Adjustment

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Sep 30, 2009

  • 1986 Answers

SOURCE: Adjust (aim) headlights on a 1990 Ford Taurus

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Nov 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to adjust headlights for 1999 silverado


there is adjusting screw in the side of the head lights and top and bottem

Feb 05, 2013 | 1999 Chevrolet Silverado 1500

1 Answer

Can't locate headlight adjuster screw 2010 siera 1500


Pop the hood and look straight down on the top of the light, behind the light there should be a screw hole (one round and one oblong) to the left and the right. You'll need a torx driver (I believe a T15) to adjust these. The round hole is for vertical adjustment and the oblong is for horizontal

Nov 07, 2012 | Cars & Trucks

1 Answer

Can't find the adjustment screws for the headlights on a 2008 Tundra


Adjust the vertical headlight aim into the specified range by turning aiming screw A with a screwdriver.
  • Perform lo beam aim adjustment.
  • The headlight aim moves down when turning the aiming screw clockwise, and moves up when turning the aiming screw counterclockwise.
  • 5687808.jpg

Oct 16, 2010 | 2008 Toyota Tundra

2 Answers

2008 Jeep Grand Cherokee has a headlight aiming problem - the low beams are aimed too high. I cannot find the vertical aiming adjustment screws to fix the problem. Can anyone tell me how to adjust the low...


Hi, i have no idea if this will help you or not, but, on the 1997 grand cherokee, if you look at the headlight itself, look to the outer edge, over the top ontop of the headlight there is a white allen key hole, not sure on the size, this, basically is the up and down adjuster for the headlight, sorry if it doesn't help but i've just had to adjust mine, and thats where it is, the one towards the radiator is the in and out, it pushes or pulls the headlight offcentre

Nov 26, 2009 | 2005 Jeep Grand Cherokee

1 Answer

Headlight pointing down, loose in housing


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 19, 2009 | 2008 Dodge Charger

1 Answer

How do you adjust the highbeam headlight on 08 G6


there is no separate for the highbeam. Basically, you are forced to use one screw for both and have to compromise

Nov 16, 2009 | 2006 Pontiac G6

1 Answer

How do you replace the head light in a '89, 2500 chevy silverado??? This one it's got the 4 head lights not just the 2. I thought that just by removing the ring around the light would do it, WRONG !!!!!! I...


1.Remove the Headlight Bezel. (Two screws go down on each side on the bottom, two screws go up in the top on each side)

2.Remove the Retaining Ring screws, and the Retaining Ring. DO NOT disturb the adjustment screws!
The Retaining Ring screws are the two screws at the top on each corner, and bottom on each corner.

The screw in the top Middle, bottom Middle, and on each side, in the Middle, are the Adjustment screws.

I advise using a pair of gloves if these bulbs are stuck, and 'stubborn'. May be going over the top with safety advice, but I would rather that you be safe, than worry about my seeming like a 'Worry-Wort'.

You may encounter, that the three prong plug on the back of the headlamp, is also hard to remove. Corrosion can develop in this area very easily.

I advise wiggling the plug back and forth a little, as you try to remove it.

Oct 07, 2009 | 1989 Chevrolet Silverado 2500

2 Answers

Can't find the adjustment knob for the headlights on a 2008 Mazda


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Jun 09, 2009 | 2008 Mazda Mx 5 Miata

1 Answer

Headlight assembly


Hello streets54, my name is JShreader. Thank you for choosing fixya.com.

First, you have to remove the Upper Radiator Grille. Behind the Headlamp at the top of the Front Bumper, access the lower inside hidden Headlamp Bolt. Only loosen the Bolt. DO NOT REMOVE. Now remove the 2 Headlamp Screws, then the Hidden Screw...now the Headlamp Housing should come out. I uploaded the procedure in .pdf format. You can download it by clicking HERE. I hope this helps you. If you have any more questions or need any more diagrams, please don't hesisitate to ask...Thanks again, JShreader!

Apr 01, 2009 | 2008 Chevrolet Silverado 1500

1 Answer

Headlight adjustment 2000 Alero


There should be 2 more screws on the headlight housing, on each housing there is one towards the middle and one towards the fender, try adjusting the one that you haven't already

Mar 01, 2009 | 2000 Oldsmobile Alero

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,887 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...