Question about 2000 Mazda MPV

2 Answers

Still have this vehicle. In 06 SSP64 work was done. The rear section of the rear heater pipes was changed. Now the front section of the rear heater pipes is corroded and sweating. I can't get a straight answer from Mazda Canada or the local dealer as to what part number LDY7-61-3BY on the SSP covers. How can I protect my vehicle from disastrous coolant loss through the corroded pipe? Was that pipe covered by SSP64? If so, how can I get them to fix it?

Posted by on

  • 3 more comments 
  • paof6 Dec 30, 2010

    I was hoping for a quick fix. There must be an alternative to spending $1,000 to replace that line. Can't I by-pass the rear heater?

  • paof6 Dec 30, 2010

    Unfortunately SSP65 is a US only SSP

  • paof6 Dec 30, 2010

    I was told $1000. to scare me or something.The cost of the part including tax here in Toronto is $99.22 cents. They say it will take 3.5 hours to complete. That's about $500. Mazda Canada finally suggested that I have the dealer verify the problem and then they'll consider what they may do. I'll get it fixed no matter what and take both Mazda Canada and the dealer to Small Claims Court if I have to.

  • paof6 Dec 30, 2010

    Yes it was. Though Mazda Canada does not recognize SSP65 this suggestion gave me some leverage. Thanks

  • paof6 Dec 31, 2010

    Thanks. I am quite handy but three things 1. It's the vehicle my wife drives. 2. I'm 6ft 6ins with big hands and there's not much room to work. 3. It's really cold outside.

    My brother used to send me shopping for Honda parts here because of the price.

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Expert
  • 1,868 Answers

Hello! Both the front and rear sections of the rear heater pipe are to be changed...Not just the rear section...There is a revised Technical Service Bulletin...Number is; (SSP65-07-010/08)...The part numbers for the Front Section are as follows...

LDY 7-61-3BX= Front section w/o rear A/C

LDY 9-61-3BX= Front Section with rear A/C

The TSB reads as follows..."Rear heater pipe (front or rear) is severely rusted, corroded, or seeping coolant...Required Action is to replace ONLY the seeping side of the rear heater pipe"...Since the front section of the rear heater pipe is seeping and corroded they are obligated to change it out...Stick to your guns...Return the vehicle to the dealership
and have them complete the work...
Guru..............Saailer
Still have this vehicle. In 06 SSP64 work was - moz-screenshot-47.pngmoz-screenshotStill have this vehicle. In 06 SSP64 work was - moz-screenshot-49.png /><img src=

Posted on Dec 30, 2010

  • 1 more comment 
  • David Burbee
    David Burbee Dec 30, 2010

    Hello! There is nothing in the TSB which restricts Canadian customers...When you had the rear section replaced was it not covered? The part # LDY7-61-3BX is the correct # for the Front Section of the pipe if the vehicle does not have rear A/C...LDY9-61-3BX if it does...The cost of the pipe is $114.27...At a local Masda dealership near me...The worse case would be to purchase the part and install it...I can put you in touch with a Mazda parts department and you could order it and have it shipped to you...I can't imagine how the cost would be $1000...Send a comment, I am here!

    Guru...saailer

  • David Burbee
    David Burbee Dec 30, 2010

    Hello! So you beat the US price! I should start buying farther north...If your handy, and it sounds as if you are, It's not that difficult of a job...$100 and your vehicle is up and running...Then, take whatever action you deem necessary...Let me know how you make out....Guru...Saailer

  • David Burbee
    David Burbee Dec 31, 2010

    Hello! I'm a little French Canadian...Actually 1/2 French Canadian...And have been known to crawl inside of instrument panels...But, I agree, it's too cold so I won't be coming up...........Saailer

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,450 Answers

The heater pipe problem was an extended warranty for 7years from purchase date. so it is out of this and i doubt you are going to get any help on it. you will need to replace pipe befor it corrodes thru. might wanna undercoat new pipe

Posted on Dec 29, 2010

  • TripleTauto
    TripleTauto Dec 30, 2010

    YES YOU CAN BYPASS THE REAR LINES at the engine just connect the two hoses together and you will do away with rear heat

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My front air is working fine on my 06 Mercury Monterey, but the back won't even put out air. This is recent


If the vehicle has front and rear heating/ac and there is no air blowing from the rear, you have a heater motor issue. Possible fuse/relay/resistor or wiring issue. Diagnostics will have to be performed to isolate the problem

Jul 14, 2015 | Mercury Cars & Trucks

1 Answer

2002 isuzu rodeo cylinder head torque lbs. for 2.2


Print


Removal & Installation

2.2L Engine

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following: Negative battery cableIntake Air Temperature (IAT) sensor connectorPositive Crankcase Ventilation (PCV) valve and hoseAir intake assemblyUpper radiator hoseAccessory drive beltExhaust front pipeAlternator and bracketsCrankshaft Position (CKP) sensor connectorKnock sensor connectorHeater hosesWater bypass hoseFuel linesEvaporative Emissions (EVAP) valve connectorCanister hoseIntake manifoldEngine wiring harness connectors at left rear of the engine compartmentPower steering pump pressure switch connectorFront coverSpark plugs and wiresCamshaft Position (CMP) sensorValve coverTiming belt. Refer to the Timing Belt unit repair section.Timing belt idler pulleysTiming belt rear coverOil pressure switch connectorCamshaftsCylinder head. Remove the bolts in reverse of the tightening sequence.

    Negative battery cable Intake Air Temperature (IAT) sensor connector Positive Crankcase Ventilation (PCV) valve and hose Air intake assembly Upper radiator hose Accessory drive belt Exhaust front pipe Alternator and brackets Crankshaft Position (CKP) sensor connector Knock sensor connector Heater hoses Water bypass hose Fuel lines Evaporative Emissions (EVAP) valve connector Canister hose Intake manifold Engine wiring harness connectors at left rear of the engine compartment Power steering pump pressure switch connector Front cover Spark plugs and wires Camshaft Position (CMP) sensor Valve cover Timing belt. Refer to the Timing Belt unit repair section. Timing belt idler pulleys Timing belt rear cover Oil pressure switch connector Camshafts Cylinder head. Remove the bolts in reverse of the tightening sequence.

To install:


0996b43f802097a8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Cylinder head torque sequence-2.2L (VIN D) engine

NOTE Use new cylinder head bolts for assembly.

  1. Install the cylinder head with a new gasket. Tighten the bolts in sequence as follows: Step 1: 18 ft. lbs. (25 Nm)Step 2: Plus 90 degreesStep 3: Plus 90 degreesStep 4: Plus 90 degrees
    1. Step 1: 18 ft. lbs. (25 Nm)
    2. Step 2: Plus 90 degrees
    3. Step 3: Plus 90 degrees
    4. Step 4: Plus 90 degrees

  2. Install or connect the following: CamshaftsOil pressure switch connectorTiming belt rear coverTiming belt idler pulleys. Tighten the bolts to 18 ft. lbs. (25 Nm).Timing beltValve coverCMP sensorSpark plugs and wiresFront coverPower steering pump pressure switch connectorEngine wiring harness connectors at left rear of the engine compartmentIntake manifoldCanister hoseEVAP valve connectorFuel linesWater bypass hoseHeater hosesKnock sensor connectorCKP sensor connectorAlternator and bracketsExhaust front pipeAccessory drive beltUpper radiator hoseAir intake assemblyPCV valve and hoseIAT sensor connectorNegative battery cable

    Camshafts Oil pressure switch connector Timing belt rear cover Timing belt idler pulleys. Tighten the bolts to 18 ft. lbs. (25 Nm). Timing belt Valve cover CMP sensor Spark plugs and wires Front cover Power steering pump pressure switch connector Engine wiring harness connectors at left rear of the engine compartment Intake manifold Canister hose EVAP valve connector Fuel lines Water bypass hose Heater hoses Knock sensor connector CKP sensor connector Alternator and brackets Exhaust front pipe Accessory drive belt Upper radiator hose Air intake assembly PCV valve and hose IAT sensor connector Negative battery cable
  3. Fill the cooling system.
  4. Start the engine and check for leaks.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Intake Air Temperature (IAT) sensor connector Positive Crankcase Ventilation (PCV) valve and hose Air intake assembly Upper radiator hose Accessory drive belt Exhaust front pipe Alternator and brackets Crankshaft Position (CKP) sensor connector Knock sensor connector Heater hoses Water bypass hose Fuel lines Evaporative Emissions (EVAP) valve connector Canister hose Intake manifold Engine wiring harness connectors at left rear of the engine compartment Power steering pump pressure switch connector Front cover Spark plugs and wires Camshaft Position (CMP) sensor Valve cover Timing belt. Refer to the Timing Belt procedure. Timing belt idler pulleys Timing belt rear cover Oil pressure switch connector Camshafts Cylinder head. Remove the bolts in reverse of the tightening sequence.

To install:

0996b43f802097a8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Cylinder head torque sequence-2.2L (VIN D) engine


NOTE Use new cylinder head bolts for assembly.

  1. Install the cylinder head with a new gasket. Tighten the bolts in sequence as follows:
    1. Step 1: 18 ft. lbs. (25 Nm)
    2. Step 2: Plus 90 degrees
    3. Step 3: Plus 90 degrees
    4. Step 4: Plus 90 degrees

  2. Install or connect the following:

    Camshafts Oil pressure switch connector Timing belt rear cover Timing belt idler pulleys. Tighten the bolts to 18 ft. lbs. (25 Nm). Timing belt Valve cover CMP sensor Spark plugs and wires Front cover Power steering pump pressure switch connector Engine wiring harness connectors at left rear of the engine compartment Intake manifold Canister hose EVAP valve connector Fuel lines Water bypass hose Heater hoses Knock sensor connector CKP sensor connector Alternator and brackets Exhaust front pipe Accessory drive belt Upper radiator hose Air intake assembly PCV valve and hose IAT sensor connector Negative battery cable
  3. Fill the cooling system.
  4. Start the engine and check for leaks.

May 26, 2012 | Isuzu Rodeo Cars & Trucks

1 Answer

Mitsubishi montero 2003 leaking anifreeze in the rear


There is a set of two steel pipes that carry coolant/antifreeze to the rear mounted heater core for heater operation. These steel pipes/tubes rust out, and you end up with a coolant leak. Mitsubishi has superceded the steel tubes with aluminum tube set. Not an easy job to replace the two pipes since they are routed over and around a few items under the vehicle before attaching to the heater core at the r/r of the vehicle.

May 04, 2012 | Mitsubishi Cars & Trucks

1 Answer

2003 ford focus catalytic converter location


SECTION 309-00: Exhaust System 2003 Focus Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 01/24/2003 Exhaust System adobe.gif Printable View (214 KB) Vehicles with 2.0L Zetec-E enginee0008758.gif
Item Part Number Description 1 - Bracket 2 - Gasket 3 - Catalytic converter 4 - Bracket 5 - Gasket 6 - Front muffler 7 - Rear muffler 8 - Hanger 9 - Flexible pipe

Vehicles with 2.0L SPI enginee0010349.gif
Item Part Number Description 1 - Gasket 2 - Catalytic converter 3 - Bracket 4 - Gasket 5 - Front muffler 6 - Rear muffler 7 - Hanger 8 - Bracket 9 - Flexible pipe

Vehicles with 2.3L PZEV Enginea0072697.gif
Item Part Number Description 1 5G232 Catalytic converter 2 5K222 Mounting bracket 3 5K282 Head shield 4 9451 Gasket 5 5A262 Insulator 6 5E292 Converter and muffler assembly 7 9448 Gasket 8 5G203 Flex Pipe NOTE: The exhaust systems shown in this section are production systems.
The exhaust systems are of a two-piece construction for production and five-piece construction for service.
Catalytic Converter
The catalytic converter fitted to the Focus range resembles a small muffler. Because of the high temperatures at which the catalytic converter operates, the vehicle body areas around the catalytic converter are protected by heat shields. The catalytic converter controls three emissions; Hydro carbons (HC), carbon monoxide (CO) and oxides of nitrogen (NOx).
Catalyst deactivation due to poisoning
Sulphur (S) in the fuel can cause deactivation of the catalyst.
Lead (Pb) in fuel can cause a severe deactivation at levels above 5 mg per liter of fuel. It is therefore essential that vehicles with catalytic converters always operate on unleaded fuel.
Zinc (Zn) and phosphorus (P) present in some oils, can cause deactivation if oil consumption is high.
The effect of sulphur is felt most if it is released from the catalytic converter as hydrogen sulphide (H2S). This has an unpleasant odor similar to rotten eggs. Changing the fuel manufacturer may help in reducing this phenomena.
To minimize H2S emissions, it is essential that the idle CO level is within specification and that the engine emission system is functioning correctly. For additional information, refer to Section 303-08A or Section 303-08B.
ani_caut.gif CAUTION: If temperatures exceeding 900°C are achieved the catalyst substrates will start to deteriorate. It is important that the cause is defined and rectified if subsequent melts are to be prevented.
Catalyst melts are normally accompanied by loss of power due to excessive back pressure. For additional information, refer to Section 303-07A or Section 303-07B.
High substrate temperatures are caused by the ignition or the fuel systems. For additional information, refer to Section 303-07A or Section 303-07B.
Misfires at high engine speed may result in an almost instantaneous melt.

2010&c18=modelyear&c20=n720709&c35=wsm%2cexhaust%20system%2cs3y%2c309-00%2cdescription%20and%20operation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 07, 2011 | 2003 Ford Focus

3 Answers

My radiator coolant dripping very fast by the muffler pipe beside the transmission.


your vehicle has a service bulletin on the metal heater hoses; they corroide and leak. They run from your heater core (front of van) to the rear most of your van by the spare tire (rear heating). This happened to mine, I had to replace the same. This is a known common problem.

Jan 21, 2010 | 2004 Kia Sedona

1 Answer

Looking for a heater core pipe (front)


If your carpet is getting wet under the dash and around , then you probably need a new heater core. If it is a simple leak that requires you to replace the hose ot clamp, then the heater core is leaking from the outside into the engine compartment instead of the inside of the car.

Apr 08, 2009 | 2002 Kia Sedona

1 Answer

Can you tell me how to change fuel pump on a 1990 chevy lumina


http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152801dbaf3

when you drop the tank by following these directions you will have access to the pump

1989-94 Vehicles
See Figures 1 and 2
  1. Disconnect the negative battery cable.
  2. Properly relieve the fuel system pressure, as outlined earlier in this section.
  3. Raise and safely support the vehicle.
CAUTION Observe all applicable safety precautions when working around gasoline. Do not allow fuel spray or fuel vapors to come in contact with a spark or open flame. Keep a dry chemical (Class B) fire extinguisher near the work area. Never drain or store fuel in an open container due to the possibility of fire or explosion.
  1. Use a suitable hand operated pump device to drain the fuel through the filler tube into an approved container.
Before disconnecting any fuel lines from the fuel tank, thoroughly clean around all hose connections.
  1. Disconnect the fuel filler vent hose from the fuel tank.
  2. Detach the fuel filler hose from the fuel filler inlet tube on the fuel tank. Position the hose out of the way.
  3. Disconnect the vapor hose from the front of the fuel tank.
  4. Detach the fuel return pipe and position the hose out of the way.
  5. Disconnect the two rear rubber exhaust hangers from the rear of the exhaust system and allow the exhaust system to hang down slightly.
  6. Unfasten the exhaust shield mounting bolts, then remove the exhaust shield.
  7. Support the fuel tank with a suitable jack.
  8. Remove the two bolts securing the fuel tank straps, then swing the straps out of the way.
  9. Lower the fuel tank enough to disconnect the vapor hose from the fuel sender assembly and the vapor hose from the vapor pipe at the rear of the fuel tank.
  10. Detach the electrical connector from the fuel sender assembly and remove the two retaining clips.
  11. Remove the tank from the vehicle, slowly to ensure all connections and hoses have been disconnected.
To install:
  1. Clean all parts well. Inspect the tank for dents, rust or other damage. On high-mileage vehicles, it may be good practice to remove the fuel pump module and replace the flexible strainer on the fuel pump.
  2. Position the fuel tank under the vehicle and raise the tank with a suitable jack.
  3. Connect the vapor hose to the fuel tank at the vapor pipe at the rear of the tank and connect the vapor hose to the sender assembly.
  4. Attach the electrical connector to the fuel sender assembly.
  5. Connect the fuel feed and return lines to the sender assembly.
  6. Raise the tank into position into the vehicle and swing the mounting straps under the tank.
  7. Install the front fuel tank strap mounting bolts and tighten to 35 ft. lbs. (47 Nm).
  8. Remove the jack.
  9. Connect the fuel return pipe to the fuel feed pipe.
  10. Attach the rear fuel feed pipe to the inlet side of the fuel filter.
  11. Tighten the line fittings to 16 ft. lbs. (22 Nm). Make sure to use a back-up wrench to prevent the fuel filter from turning.
  12. Connect the vapor hose to the vapor pipe at the front of the vehicle.
  13. Attach the fuel filler vent hose to the tank. Connect the fuel filler hose to the fuel filler neck of the tank.
  14. Install the exhaust heat shield and the mounting bolts.
  15. Position the exhaust system and install the rubber hangers.
  16. Carefully lower the vehicle, then refill the fuel system
  17. Connect the negative battery cable, then install the fuel filler cap, if not done already.
  18. Turn the ignition switchONfor 2 seconds, OFF for 10 seconds, thenONand check for fuel leaks.

Jan 14, 2009 | 1998 Mercury Sable

2 Answers

Heater valve


there is no heater control valve in this truck, heat control is done through what are called blend doors. So the issue may be the front blend door motor has failed, this is very common on all Ford heatimng systems except the Focus.

Dec 15, 2008 | 2000 Ford Expedition

1 Answer

Cold air coming from rear vent of 2000 mazda mpv


Your ventilation shutter is not closing properly.

Nov 17, 2008 | Oldsmobile Bravada Cars & Trucks

Not finding what you are looking for?
2000 Mazda MPV Logo

Related Topics:

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...