Question about 2009 Nissan GT-R

1 Answer

How do you turn on launch control - 2009 Nissan GT-R

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 56 Answers

For 2010 and earlier GTR's... need to select drive, push leaver over to select manual mode, then opush the suspension into R mode, push the gearbox into R mode and push the VDC switch into OFF, left foot the brake, flat to the floor on throttle, let go of the brake pedal and hold the f*** on!
be aware is very violent on the vehcile and can destroy gearboxes. if its still under warranty the dealers can tell if this has been done may not pay to repair.
the sequence is different for the 2011 GTR's all three switches must be in R. and is covered by warranty.

Posted on Jan 08, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake light starts blinking then car parking brake turned itself on then releases car LAUNCHES forward all the lights on the dash go CRAZY and the brake goes on again where it STALLS


I think you need a main agent before you do something damaging. I get the impression there is moisture in a control unit socket/plug harness. Or its loose

Feb 17, 2016 | 2011 Subaru Legacy

1 Answer

What should the voltage be on a 2008 isuzu d teqs scv(suction control valve) please advise


P0016 Crankshaft Position/Camshaft Position Correlation Bank 1 Sensor A
P0562 System Voltage -Low
P0661 Intake Manifold Air Control Solenoid -Circuit Low (Bank 1)
P0065 Air Assisted Injector -Range/Performance
P0091 Fuel Metering Solenoid - Short To Earth
P0500 Vehicle Speed Sensor

I think you have a faulty loom multiconnector in the engine compartment ,either the wires have the insulation turned to powder of the connections are corroded ,well something drastic but simple wher eand what without my head in the engine i honestly couldnt tell you

Nov 03, 2014 | Cars & Trucks

1 Answer

Interior lights not go off


try to turn off the dash light switch a little, the light is controlled by that switch.
Launch X431 scanner

Jul 08, 2013 | Oldsmobile Intrigue Cars & Trucks

1 Answer

PLUGED IN TRALER LIGHTS NOTICED THE FLASHING ABS LIGHT ON DASH TURNED TRUCK OFF THEN STARTED IT BUT IT WOULD NOT SHIFT INTO GEAR i REPLACES FUSES AND BRAKE SHITCH AT BRAKE


Use the instrument brightness control to adjust the dash lights. If the brake light is on, release the emergency brake. ------------------------------------------------------------------------------
Original Launch X431 Master

Mar 12, 2013 | Cars & Trucks

1 Answer

How do I replace the steering column headlight/ turn signal control switch on a renault Modus


1. Park the car with the steering wheel centered and the wheels straight ahead. 2. Locate and remove the "Airbag" or "SRS" fuse in the passenger side fusebox. There is more than one fuse for the airbag system, so I like to start the car after step 2 to verify the Airbag light in the dash remains lit. This way you know for sure that you pulled the correct fuse.-----------------------------------------------------------------------------------
Original LAUNCH Code Reader Creader VII

Mar 07, 2013 | Cars & Trucks

1 Answer

2004 pacifica won't stay running. temp gauges are erratic. No code on PCM


The PCM on a 2004 Ford Mustang is a combined control unit, consisting of the engine control unit (also known as an ECU) and the transmission control unit.------------------------------------------------------------------------------------------
Launch X431 Master

Mar 07, 2013 | Chrysler Pacifica Cars & Trucks

Not finding what you are looking for?
2009 Nissan GT-R Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...