Question about Fiat Strada

1 Answer

Hi, I have a fiat multipla 03. recently had the fly wheel and clutch replaced. The car now has a rocking effect at low speed and vibration at higher speeds. could the mechanics have put back something wrong with the transmition or cv joint?

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 166 Answers

Yes they could have not tighten the clutch bolts and some may have came out that can cause very bad damage

Posted on Dec 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi where do I find the plug to change my gearbox oil for a fiat multipla 1.6 petrol y reg


Drain should be at the lowest point of the trans, with fill plug about half way up on one side.

Jan 07, 2015 | 2007 Fiat Multipla 1.6

1 Answer

Can i change flooded 1.9l engine 05 with 02 1.9l engine


Yes you can. As long as it's a diesel engine and the same model range (Multipla).

Mar 23, 2013 | Cars & Trucks

1 Answer

Multipla stiff gear change


Fiat but found an inexpensive manual http://global-data.co.uk/products.php?product=Fiat-Multipla-Workshop-Manual&setCurrencyId=2 I am not affiliated with them. I just thought if you needed it. Also FIAT forums may have your info.

Sep 16, 2012 | 2005 Fiat Multipla 1.9

1 Answer

Vibration on 2004 Cadillac Deville


If a hub bearing was bad, it almost always would make noise, more so when changing lanes at higher speed. Outer CV joints make a loud low pitched rattle when turning (corners). Inner CV joints raise hell at high speed- bad shake! Sway links affect cornering and clunk when hitting rough patches of road surface.
Is the vibration worse at 65 than at 50? If so, you are dealing with a wheel balance situation. Find an old time front end shop that will check the balance on the vehicle. You will have to turn off the traction control to do this or use an on-the-car wheel balancer.
If you feel it at some low speeds at it comes back at other higher speeds, then you are dealing with tire roundness. Possible more than 1. More common than we would like.

Jul 17, 2017 | 2004 Cadillac Deville

1 Answer

How to bypass fuel cut off switch on fiat multipla


Replace the switch don't bypass it this indicates an issue with your fuel check with your fiat dealer

Jul 30, 2012 | 2006 Fiat Multipla 1.6

3 Answers

Vibration at 60mph


Hi vibration at 60 is normally wheel balance not the alaignment, get the 2 front wheels weighted and balanced, if they are wearing unevenly then it could be suspension bushes,track rod ends.

But most likely the wheels just need balancing only cost about $20 to 30 max

Hope this helps
Regards
Dan

Feb 14, 2010 | 2001 Mercury Sable

2 Answers

2003 cavalier buzzing/growling noise


try the rear wheel hubs the noise will travel true the car making it sound like it up front

Jul 15, 2009 | 2004 Chevrolet Cavalier

1 Answer

How do i replace front discs on a fiat multipla,51,plate,please.


Firstly removve the wheel. Then romove the the caliper by the two hex/alen key screws at the rear. then remove the guard by the two bolts at the front. this should leave only the disk on the hub. there is a small screw on the front which will realease the disk and fitting is te reverasal of removal.

Jun 01, 2009 | 2006 Fiat X1/9

2 Answers

Fiat Multipla 2002


In all these cases it appear to be a problem with the synchronizers or a dented pinion. To verify, the oil can be check for metal deposits. Fiats have bronze synchronizers and when placed under heavy shifting load they were out rapidly. if this is the case replacement is the solution and transmission has to be open. The car can be driven but gear will keep releasing. Sometimes the synchronizer level bends causing an incomplete setting off the gear.

Jun 19, 2008 | 2006 Fiat X1/9

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

311 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fiat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76691 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Fiat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...