Question about 1991 Peugeot 405

1 Answer

Where are the timing marks for a peugeot 1.9 td 306

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,098 Answers

Hi

Hope this is helpful, if you need more info get back to me.


1, park car, handbrake on
2, loosen drivers side front wheel bolts,
3, crawl under car use 22mm socket and breaker bar to loosen the crankshaft pulley bolt, it'll probably be quite tight, once undone nip it up again not to tight,
4, open bonnet,
5, jack drivers side of car up, put on axle stand
6, remove wheel
7, loosen and remove intercooler bolts, then intercooler
8, find 6mm allen key
9, behind the starter motor there is a hole in the gearbox housing, put the allen key in it, (may be easier to undo and remove the 3 starter motor bolts)
10, get a 22mm socket put it on the crankshaft pulley bolt, turn the crankshaft bolt clockwise whilst at the same time pushing the allen key into the hole (easier with an assistant but can be done solo) keep turning until the allen key drops into the hole(you'll understand when you do it, may have to turn the engine for quite some time reasonably slowly),
11, thats the engine now on it's timing marks,
12, now put a trolley jack and block of wood under the sump and jack it up until it takes the weight of the engine,
13, remove the left hand side engine mount, basically move the fuel primer to one side, remove the rubber bung if there, then carefully undo the 4 5/8 size bolts and remove the top half of the mount (careful engine doesn't suddenly slip of jack and trap your hand),
14, now remove the 10mm bolts holding the front cambelt cover on, then do the same for the rear cover, except there is one bolt at the back of the cover which is 11mm,
15, now looking at both of the exposed pulleys you will 2 timing holes with a threaded insert behind, on the cam pulley it's at about 4 o clock and i think 2 o clock on the fuel pump, now find the 2 short bolts from the intercooler, they are the right size to fit in the timing holes,
16, now under the arch, remove the crankshaft pulley bolt and pull of the pulley,
17, now remove the lower cambelt cover, all 10mm bolts,
18, now look at the new belt tensioner and you'll see a square hole in it, find the same hole on the car, a short 3/8 socket extension will fit in there and you can then use a ratchet to apply or release the tension,
19, undo but don't remove the two bolts holding the tensioner, now use your ratchet to push the tensioner towards the windowscreen, whilst holding it there use your other hand to release the belt from behind the tensioner,
20, with the belt now loose remove it from round the rest of the components,
21, now replace the waterpump,
22, now replace both the tensioner and idler pulley, to do this you'll need to remove the rest of the metal engine mount, the bolts are quite obvious,
23, replace the belt in the same manner you removed it,
to tension the new belt pull the ratchet towards you then tighten the tensioner bolts at the same time,
24, with the tensioner tightened push the belt in the middle between the two pulleys you should have about half an inch of deflection if correct (check the old belt before removing to give you an idea),
25, now remove the two timing pins in the pulleys and the allen key,
screw the crankshaft pulley bolt into it's hole (leave the pulley off) if you keep screwing it in then the engine will turnover,
26, turn the engine over by hand at least 8 times, then put the timing pins back in as you did at the start, if you've done it all right it'll turn over with no issues
27, recheck the tension again,
28, if alls well then refit the lower cambelt cover,
29, refit the crankshaft pulley,
30, refit everything you've removed, torque all required bolts correctly (except crankshaft pulley which is done last)
31, remove the allen key (2 intercooler bolts will have already been done when fitting the covers and intercooler,
32, turn the engine over again by hand to check there's no rubbing on the cam covers or any other issues,
33, if alls well then top up the engine coolant as you'll have lost alot when doing the waterpump, bleed it properly,
34, put the road wheel back on, lower the car to the ground then torque up the crankshaft pulley bolt,
35, job done start her up then tidy up

Regards

Dan

Posted on Dec 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, I need some help please! I have a peugeot 406 2.1 td p reg. I've had to put a 1.9 bosh pump on it to bipass the imobiliser. does any one know what order the injection pipes go in. cheers ale


Hi Alex, The firing order is 1-3-4-2. When fitting the injector pump I hope you noticed the match marks for timing. When fitted and aligned the engine will be at TDC firing on one. To identify # 1 on the pump, connect the fuel supply and bleed air from the system and rotate the engine one and three quarter revolutions by hand, having someone watch which outlet ejects fuel when passing TDC completing the second rotation. That will indicate number one piston. Follow the firing order for the remaining three. Regards John

Nov 16, 2012 | Cars & Trucks

1 Answer

Peugeot 306 1.9d DW8 can you replace spring damper & 2 adjuster rollers with 1 single self adjusting roller as on HDI


Cannot honestly say as never done this particular job on a peugeot ,there again i might have and dont remember but a quick check here is to ask in the auto factor as they will know for sure as they supply the parts to the trade.

Oct 23, 2012 | 2000 Peugeot 306

1 Answer

Timing belt 1997 306 1.9 td


hallo
hope it helps
marko
94b52e0.jpg

Oct 08, 2009 | 1991 Peugeot 405

1 Answer

How do i disable airbag warning light on peugeot 306 lx td


have you plugged the air bag wires back in under the seat?
if you have put after market of non genuine seats in you will not be able to turn light off
you could remove the bulb from the dash or just leave it (it will not affect the mot)

Sep 18, 2009 | 1989 Peugeot 405

1 Answer

What is the frequency that a cambelt should be changed 306


useualy at 100000 klms there will be a light that comes on at that distance to tell you ,if you are sure that the odmeter reading is correct then dont worry .if not you can change it tobe sure

Sep 06, 2009 | 1991 Peugeot 405

1 Answer

Peugeot 806 timing marks


petrol or diesel,
diesel uses 8 mm bolts pin under starter,1.9 td
petrol i need to know what size engine

Jun 17, 2009 | 1987 Peugeot Liberte

Not finding what you are looking for?
1991 Peugeot 405 Logo

316 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

mike hayward

Level 2 Expert

279 Answers

lloyd cole

Level 2 Expert

250 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...