Question about 1997 Toyota Camry

2 Answers

Keyless remote My keyless entry for my 1997 camry is not working. I installed new batteries. Did not help. Is there a fuse somewhere for this?

Posted by on

  • suchgub Jul 16, 2008

    i did try to instal new battery in my camry 97 when i put on the terminal wire my alarm went on and i did try to put it off by remote panic swuitch but didnot work. what should i do?

  • Anonymous Mar 19, 2014

    Remote receiver location

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 28 Answers

That security horn working with seprate battery it will never swithoff
if you remove the battey terminal your remote will not work

what you wan to do excatly with your car??
if you have problem with car battery and you wan to change it
first remove the key from ignition and then chage your battery

in case of others write me ? 00971 50 5764166

Posted on Jul 17, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

There are fuses - 10a "guage" fuse, 30a "power" fuse, 25a "door" fuse, and 7.5a "dome" fuse - but I doubt that those are the problem. You can check them anyway. Might be a problem for a dealer.

Posted on Jul 14, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 crown vic keyfob only works with ignition in run position .keyless entry and door locks work fine.even tried new keyfob.no change


The keyless entry system consists of the following components:
  • driver door module (DDM)
  • keyless entry transmitter
  • keyless entry keypad
The driver door module (DDM) receives inputs from the digital transmission range (TR) sensor, ignition switch, brake switch, window/door lock switches, lighting control module (LCM), keyless entry keypad switch and remote transmitter. The DDM outputs consists of keyless entry keypad switch illumination, power door lock actuators, luggage compartment release solenoid, horn relay, and lighting control module (LCM).
  • Battery junction box (BJB) fuses:
    • circuit breaker 7 (20A)
  • Central junction box (CJB)
    • 4 (10A)
    • 6 (15A)
    • 8 (25A)
    • 13 (5A)
  • Keyless entry keypad switch
  • Power door lock actuator
  • Luggage compartment release switch
  • Luggage compartment release solenoid
  • Connectors or connections
  • Wiring harness
  • If fuse's good have checked for DTC'S - diagnostic trouble codes .
  • B1526 Keyless Entry Circuit Short to Ground DDM Go To Pinpoint Test E . B1553 Decklid Release Circuit Short to Battery DDM Go To Pinpoint Test B . B1751 Park/Neutral Switch Circuit Short to Battery DDM Go To Pinpoint Test K . B2425 Remote Keyless Entry Out of Synchronization DDM Go To Pinpoint Test L Need a professional grade scan tool to check fro these codes . Not a code reader for OBD2 codes .
  • The doors do not lock/unlock using the remote transmitter
  • Remote transmitter not programmed.
  • Remote transmitter.
  • DDM.
  • Go To Pinpoint Test F .

Did you program the new key fob ?

Remote Transmitter Programming NOTE: All remote transmitters are programmable and must be set at the same time.
  1. Turn the key from OFF to RUN four times within three seconds, ending in RUN. The locks will then lock and unlock, confirming program mode has been entered.
  1. Press any button on each remote transmitter to be programmed. The doors will lock and unlock to confirm that each remote transmitter has been programmed.
  1. If additonal remote transmitters are to be programmed, repeat Step 3 within 7.5 seconds or steps 2 and 3 if more than 7.5 seconds have elapsed.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
  1. NOTE: Failure to wait at least 20 seconds will cause programming failures. Wait at least 20 seconds after turning the key to OFF or after the last remote transmitter has been programmed to activate a remote transmitter for testing or verification

Feb 19, 2017 | Cars & Trucks

1 Answer

Keyless remote wont work. remote is transmitting a signal


chances are the remote keyless entry module (RKE) has electrical issues, see if there are problems with wiring, connectors or fuses.

Dec 23, 2010 | 2003 Toyota Camry

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

2 Answers

Keyless entry only works at very close range.


the batteries are getting weak in your remote control. your dealer should have them in stock and be able to change them for you on the spot.

Jan 26, 2010 | 1997 Ford F250 SuperCab

1 Answer

How to program a keyless entry for land rover


MOST OF THE TIME WHEN YOU HAVE PROBLEMS IN THE REMOTE AND KEYLESS ENTRY.THE DEALERSHIP HAS TO REPROGRAM IT.BUT FIRST CHECK ALL THE FUSES AND RELAYS.IF THEY ARE OKAY.THEN DEALERSHIP HAS TO FIX.

Sep 16, 2009 | 2004 Land Rover Discovery

1 Answer

How do i program remote keyless entry? I replaced the battery and keyless entry quit working,


You don't normally program a keyless entry, that's done for you by the technicians that install that. If the replaced battery doesn't solve the problem, take the battery and the remote to the techies that installed it.

Mar 27, 2009 | 2003 Chevrolet Monte Carlo

1 Answer

Both of my keyless entry remotes just stopped working any ideas


sometimes you have to hold the lock and unlock at the same time and stand close to your jeep until the locks unlock and lock agian if that works then they are reset if not than try to change the batterys in one remote and retry

Mar 11, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Keyless entry remote


TRY PUTTING IT IN IGNITION TURN IT SO DASH LIGHTS UP THEN PRESS THE FOB WORKED ON MY CAR BUT MINE WAS A ASTRA

Oct 23, 2008 | 1997 Buick Century

2 Answers

Keyless entry module


Under the hood fuse panel, my 1997 doesn't have keyless entry so it might be aftermarket.

Aug 07, 2008 | 1997 Mazda MX-6

2 Answers

Keyless / remote control - Toyota vienta vxi


No, not true. We replace remotes regularly, and have never had a need for a "working" remote. The keyless entry system does not "disable" itself. Hope this helps.

Jul 12, 2008 | 2003 Toyota Camry

Not finding what you are looking for?
1997 Toyota Camry Logo

500 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...