Question about 1995 Mitsubishi Montero

1 Answer

Crank shaft pulley it's lose - 1995 Mitsubishi Montero

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 835 Answers

CAN U TIGTHEN THE BOLT ON IT .OR IS LOOSE AROUND WHERE THE RUBBER SPACER IS IF IS RE PLACVE IT

Posted on Dec 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1.8l. How do I replace front seal?


1. remove all the fan belts on the main (crank shaft pulley)
2. Lose the bolt of the pulley, Use a puller to remove the pulley (if neccesary)
3. Use a screwdriver to remove the oil seal...
4. Insert a new oil seal (but reduce the spring by 25-40mm by cutting it)
5 couple it!!!

Nov 24, 2015 | 2003 Kia Spectra

1 Answer

Crank shaft pulley not aligned


You may have a bad bearing or bushing in one of the idler pulleys, the belt tensioner, or the alternator. Normally the crankshaft pulley aligns unless somebody changed timing gears or the pulley itself and it's not all the way in.

Jan 27, 2013 | 2001 Chevrolet Malibu

1 Answer

Crank shaft pulley


crank sensor damaged when changed crank pulley.

Aug 05, 2012 | Toyota Camry Cars & Trucks

3 Answers

How to set timing when you relesh tensioner and it changes the alignment postion of pullies 2000 ford ranger 2.5 l


Here is the trick. Align marks. Put the timing belt on the crank shaft pulley first, and after on the overhead cam pulley. Release tensioner and rotate the crank shaft till the timing belt makes two full circles. Try to align marks, you will be at least one tooth off. Align the crank shaft on the mark, and find out how many teeth you are off at the cam shaft pulley. Count the teeth. Remove the timing belt from cam shaft pulley only. Move cam shaft pulley in reverse according to the number of teeth you counted. Make sure the crank shaft pulley is on the mark. Mount the belt at cam shaft pulley.Rotate the belt two circles and check the marks. Repeate this procedure til after releasing the tensioner, and rotating the timing belt two full circles, the mars will be align.

Nov 22, 2010 | 2000 Ford Ranger SuperCab

1 Answer

Bottem pulley on engine block is making noise, I think the bearings are going out. What is this pulley attached to and can it be lubricated?


the bottom pulley is the crank pulley. It is attached to the crank shaft. It has two parts, an inner and an outer that are joined together with a rubber isolator. Over time the rubber breaks down and the inner part part of the puller will start to rotate independently from the outer part of the pulley creating a unigue clacking noise.

To solve this you'll need a standard crank pulley puller set. You'll remove the crank bolt and then use the pulley puller to pull the crank pulley off of the crank shaft. The install the new pulley making sure to torque the crank pulley bolt to the proper spec.

Nov 06, 2010 | 1998 Buick Park Avenue

2 Answers

How do you change the crank shaft pulley?


If you have the 3.5l engine, and you don't remove the right side engine cradle bolts, you will not have enough room and will strip out the bolt when you go to put it back in. There is only one belt. There is not a woodruff key on that engine, and the pulley can go back on any which way.



40791f1.jpg
Check out the pix at http://99intrigue.shutterfly.com/headgasket/137

and following.

Apr 03, 2010 | 2000 Oldsmobile Intrigue

2 Answers

Where is the crank sensor located on a chevy malibu 2001


It should be down near the crankshaft pulley. Remove the the right front wheel and the splash shield, it should be there next to the pulley.

Dec 20, 2009 | 2001 Chevrolet Malibu

1 Answer

Crank shaft pulley


Not too hard if you have a pulley puller. Remove the belt, remove the crank shaft bolt, pull the crank pulley off, then reinstall in reverse order.

Jul 02, 2009 | 1990 Oldsmobile Cutlass Ciera

1 Answer

Hi, I keep losing power and stalling when I'm driving and it almost feels like I am running out of gas. The car will just refuse to start again or start and lose power after a short spell. Then, magically...


First check the gas cap for venting. Toyo are known to create a vaccum on the gas tank. Second, has the gas filter been changed. 3rd, Check the timing gear on the crank shaft. the key slot tends to wear throwing the timing out. If there is any play in the crank shaft pulley it is a good sign. Good Luck

Dec 26, 2008 | Toyota Corolla Cars & Trucks

1 Answer

Crank shaft inner pulley lose on 2003 Exterra 3.3


I don't have one. I have the same problem can someone help?

Oct 16, 2008 | Nissan Frontier Cars & Trucks

Not finding what you are looking for?
1995 Mitsubishi Montero Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...