Question about 1993 Pontiac Sunbird

1 Answer

How to remove and replace starter on 4cyl? - 1993 Pontiac Sunbird

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Expert
  • 45 Answers

Disconnect the battery +wire FIRST ! disconnect the wires from the starter relay switch(on the top of the starter) there are 3 or 4 bolts holding it on ,unscrew them and off you go .

Posted on Dec 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 toyota camry 4cyl.engine doesnt turn over but starter does.starter ck. and is ok , just makes starter whining noise


if starter motor runs (hear it??) but doesn't turn engine , then it needs to be replaced also at same time , the gear it contacts with on flywheel edge ,needs to be visually inspected (easy with starter removed) for any missing or bent teeth , as a engine this old is bound to have some worn or missing teeth, if gear is missing teeth or are very worn (teeth looks like a shark fin with hook to them) then engine and transmission will need to be separated to be replace the gear , most shops will just remove engine to allow for this , but this isn't always nessacary

Dec 14, 2016 | Toyota Cars & Trucks

1 Answer

How do you replace the starter on a 2001 Isuzu Rodeo 4cyl 2WD?


Remove the battery earth cable. Engage parking brake and chock the wheels. The starter is on the lower rear left hand side of the engine. Remove the starter supply cable by undoing the 13mm nut on the rear of the solenoid. Unclip the start wire on the side of the solenoid by squeezing and then pulling the connector plug. Undo the mounting bolt on the top of the starter first. and remove. Then the bottom one. Doing it this way round will make it easier to undo the bolts by hand once loosened.
Pull the starter to the front of the car and remove.

Aug 21, 2010 | 2001 Isuzu Rodeo

2 Answers

How do i get out the starter no room to remove it


the starter will come out, but toward the front and drop the sway bar to do so

Mar 07, 2010 | 1996 Nissan Pickup

1 Answer

How to remove starter solenoid from 1998 Honda Accord LX 4cyl?


the starter solenoid is integral to the starter.

Dec 26, 2009 | 1998 Honda Accord

1 Answer

Replace a starter


1999 Honda Civic DX 1.6L MFI SOHC 4cyl
Starter Removal & Installation

c4ae816.gif

Fig. Starter wire connections

304d19e.gif

Fig. A ratchet and long extension may be needed to remove the starter

The factory sound system has a coded theft protection system. It is recommended that you know your reset code before you begin.
  1. Disconnect the negative battery cable.
  2. Remove all wiring from harness.
  3. Remove the lower radiator hose from the bracket on the starter motor.
  4. Remove the starter cable from terminal B located on the back of the solenoid.
  5. Remove the black/white wire from the S (solenoid) terminal.
  6. Remove the two bolts that mount the starter to the transaxle assembly.
  7. Remove the starter.

To install:
  1. Install in the reverse order of removal.
When installing the heavy gauge starter cable, make sure the crimped side of the terminal end is facing out.
  1. Enter the anti-theft code and radio presets.

I hope help you with this (rated this help). Good luck.

Sep 09, 2009 | 1998 Honda Civic

2 Answers

How to replace starter on 1998 isuzu amigo 2wd 4cyl


Removal
1. Battery ground cable.
2. Remove harness connectors
3. Remove bolts from starter.
Installation
1. Install starter assembly.
2. Install mounting bolts and tighten bolts to specified
torque
Torque: 25 N·m (18 lb ft)
3. Connect harness.
4. Reconnect the battery ground cable

Jul 02, 2009 | 1998 Isuzu Amigo

1 Answer

Best Method to Replace Starter on 1993 Pickup


According to the online manual at AutoZone, you need to remove the right front wheel, the front gravel shield, the exhaust manifold heat insulator, the exhaust manifold, and detach the oil pressure switch connector. The picture shows lifting the starter out from the top once it is unbolted.

I've changed the starter on a '95 with a 4 cylinder engine, and the top bolt was a bugger to get to, requiring two extensions and a universal on my ratchet set. Good luck!

Mar 09, 2009 | 1993 Nissan King Cab

1 Answer

Toyota starter problrm


NEED TO REPLACE STARTER.

Mar 03, 2009 | 1996 Toyota T100

1 Answer

99 Jetta starter removal


http://forums.tdiclub.com/showthread.php?p=844411 this how to should work even if your car is the older style 99 they have the same layout for all 4cyl engines

Feb 12, 2009 | 1999 Volkswagen Jetta

1 Answer

Removing starter heat shield on 2000 Passat 4cyl Turbo


I am not sure if I have the right engine but this may help and give you a better idea of what you are doing.

2-Wheel Drive (2wd) Models (2wd) Models
2.2L Engine
  1. Remove or disconnect the following:
    • Negative battery cable
    • Front exhaust pipe, if necessary for access
    • Starter heat shield, if equipped
    • Brace rod from the front of the engine and the bell housing
    • Drivers side wheel to access the starter motor wires and the starter motor attaching bracket-to-engine bolt through the opening in the wheel well
    • Wires from the starter solenoid
    • Attaching bracket-to-engine mount bolt
    • Starter-to-engine block bolts. When removing the last bolt, be sure to support the starter to keep it from falling and possibly injuring you.
    • Starter and shims (if equipped) from the vehicle
    • Bracket from the starter assembly, if equipped 0900c15280096824.jpgStarter motor and related components—2.2L engine
To install:
  1. Install or connect the following:
    • Bracket to the starter, if removed. Tighten the bracket nuts to 97 inch lbs. (11 Nm).
    • Starter and shims (if equipped) into position in the vehicle and thread one of the retaining bolts to hold it in position.
    • Bracket-to-engine mount bolt (loosely), if equipped
    • Starter mounting bolt, then tighten all mounting fasteners to 32 ft. lbs. (43 Nm)
    • Wiring to the solenoid
    • Brace rod and tighten the retainers
    • Front exhaust pipe and tighten the fasteners, if removed
    • Starter heat shield, if equipped
    • Driver’s side wheel, if removed
    • Negative battery cable

Nov 27, 2008 | 1999 Chevrolet Tahoe

Not finding what you are looking for?
1993 Pontiac Sunbird Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...