Question about 2000 Daewoo Lanos

1 Answer

I need to change my Front wheel bearing on my 2000 Daewoo lanos s. Does the bearing come in just the bearing or the whole hub assembly?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 3,113 Answers

Press in bearing.

Posted on Dec 29, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I have a knocking sound coming from the drivers side wheel whils turning corners

can be anything check strut/shock hub/wheel bearings,cv joints/axle brake pads,ball joints,steering rack most probable problem would be ur hub/wheel bearings

Feb 26, 2010 | 2000 Daewoo Lanos

2 Answers

I need part number for the rear wheel bearings left and right , inner and outter for Daewoo lanos 2000 model

Daewoo rear wheel bearing parts numbers are
94535209 and each per side

Jan 06, 2010 | 2000 Daewoo Lanos

1 Answer

How to change front wheel bearings on 2000 mitsubishi galant. i have to change the whole hub assembly?

quite a difficult job without the use of a press but if you can see a circlip either side of hub you can change just bearings but normally you would have to press drive flange out of hub first to see any circlips

Aug 20, 2009 | 2000 Mitsubishi Galant

1 Answer

My Daewoo Lanos has a really loud noise in the front of the car. I was told it was the wheel bearing or hub bearing. I'm not sure what to do with it. Also my a/c doesn't work and when I turn it on it makes...

Wheel bearings are difficult to tell which of the four at times.
Be sure to be adviced by an old fox in the game. Cars are sound boxes. I had a car and it actually was the last bearing being the guilty one. Wheel and hub bearing is the same to me. And there are other bearings there. Better shop around for cost estimate and guarantee on repair. DIY can be more costly if no mechanic. You pay parts and go about with DIY risks you pay at all times.
And official dealers are not allways the best. Dry not moving plastic hub caps can make a lot of nasty noise at low speed in narrow streets or underground parkings. If you have those get them off clean tyre rims and caps and grease them slight with teflon spray or so. Refit. Cost virtually nothing. Also make up other items coming up fore replacement not to overinvest in old wrecker with corrosion or too high mileage. Maybe your's is fine but calculate ahead. Including totall loss value on accident.

May 06, 2009 | 2000 Daewoo Lanos

1 Answer

Severe bearing noise from front wheel bearing/cv joint area.Cv joint still lubricated,I tend to think axle support bearing is dry & on the way out,but only assuming.How does front wheel bearing come out of...

you have to replace bearing and hub as a have to remove remove brakes and caliper rotor set them aside dont disconnect brake line. get a piece of clothes rack wire to hold brake caliper .do not let it hang by brake hose. you got to remove hub nut. best way to do that is loosen it a litttle while tire still on weight of car keep wheel from turning .

May 03, 2009 | 1999 Daewoo Lanos

1 Answer

2001 daewoo lanos front passenger bearing

Remove the wheel ,then track end ,brake caliper support ,the pinch bolt that holds housing to the strut ,lower track control arm swivel.pull off and place on bench .knock the centre hub piece out and on the inside of the housing is a big circlip that holds it in .Then take to a garage and have the old one pressed out and the new one pressed in.stripping shouldnt take more than 35mins ,visit to garage for the pressing?? allow 2 days --- refitting max half hour

Mar 18, 2009 | 2001 Daewoo Lanos

1 Answer

How to replace front wheel bearings on 2000 Daewoo Lanos

they come as a whole assembly hub and all

Feb 15, 2009 | 2000 Daewoo Lanos

1 Answer

Daewoo lanos

your brakes are keeping i on the dum try a puller and a hammer

Oct 18, 2008 | 1999 Daewoo Lanos

Not finding what you are looking for?
2000 Daewoo Lanos Logo

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

78289 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides