Question about Saturn SC2

1 Answer

How do I change out the rear tail lamps? - SC2 Saturn Cars & Trucks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Expert
  • 45 Answers

Open your trunk and you should see the nuts that hold your lights in place .There is a cover over those fittings that you will need to pull back before you can see the back section where your tail lights are bolted on.

Posted on Dec 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing backup bulbs on 2005 buick rendevous


TAIL LAMP ASSEMBLY AND /OR BACKUP, SIDEMARKER, STOP, TURN SIGNAL BULB REPLACEMENT

REMOVAL PROCEDURE

1. Open the liftgate.
2. Remove the screws from the tail amp.
3. Slide the tail lamp rearward in order to disengage it from the retainers on the rear body panel.
4. Disconnect the electrical connector from the tail lamp wiring harness.
5. Remove the tail lamp and side marker lamp sockets from the tail lamp, depressing the locking tab and turning counterclockwise.
6. Remove the bulbs from the tail lamp and the side marker lamp sockets, if replacing the bulbs.

INSTALLATION PROCEDURE

1. Install the bulbs to the tail lamp and side marker lamp sockets, if removed.
2. Install the tail lamp and side marker lamp sockets to the tail lamp, turning clockwise until the locking tab is fully seated.
3. Connect the tail lamp electrical connector to the wiring harness.
4. Position the tail lamp retainer slots to the tabs on the rear body panel.
5. Install the tail lamp to the rear body panel, pressing into place until fully seated.
6. Install the tail lamp screws to the Taillamp.

NOTE: Refer to Fastener Notice in Service Precautions.

Tighten the tail lamp screws to 2 N.m (18 lb in).

7. Close the liftgate.

Apr 16, 2017 | Buick Cars & Trucks

1 Answer

Change license plate bulbs in 2004 buick lesabre custom


  1. Disconnect the tail/back up lamp harness connector from the from the body wiring harness.
  2. Remove the tail/back up lamp assembly from the rear compartment lid.
  3. While supporting the tail/back up lamp assembly, unplug the tail/back up lamp harness grommet from the rear compartment lid and remove the tail/back up lamp from the vehicle.
  4. Remove the license plate lamp bulb from the lamp housing.

Sep 22, 2014 | 2004 Buick LeSabre

1 Answer

2009 impala rear turn signsl bulb replacement


Tail Lamp Replacement Impala
1596323.gif
tif.gif
Callout
Component Name
Preliminary Procedures
  1. Open the rear compartment lid.
  2. Remove the nut securing the rear compartment trim the backside of the tail lamp assembly.
  3. Pull down the rear compartment trim liner.
1
Tail Lamp Assembly Nuts (Qty: 2)
Caution: Refer to Fastener Caution in the Preface section.
Tighten
2 N·m (18 lb in)
2
Trunk Trim Line Nut
Tip
Ensure the trim liner nut is installed after the liner is repositioned in the rear compartment.
3
Tail Lamp Assembly
Tip
Pull rearward to remove and connect the electrical connector and push lamp inward in order to position the lamp to the body panel.
4
Rear Lamp Harness Connector
Ensure to connect the lamp harness connector before securing the lamp to the rear body panel.

Jul 29, 2011 | Chevrolet Impala Cars & Trucks

2 Answers

How can i change a tail light an a sorento kia 2008? I can t reach the connector inside..... What do i have to take off? Thank you


To Remove

1. Disconnect the negative (-) battery terminal.
2. Loose the 2 screws holding the rear combination lamp then disconnect the connector. And then remove the outside rear combination lamp assembly.
3. Remove the bulbs from the rear combination lamp assembly.


tecnovative_179.gif

tecnovative_180.gif
To Install

1. Connect the bulbs to the rear combination lamp assembly.
2. Connect the rear combination lamp connector.
3. Reassemble the rear combination lamp assembly.

Mar 24, 2011 | 2007 Kia Sorento LX 4x4

1 Answer

What do I need to unscrew in the trunk to change the reverse light in my 01 chevy impala


Tail Lamp Assembly Removal & Installation To Remove:
  1. Open the rear compartment.
  2. If equipped, disconnect the cargo net.
  3. Remove the wingnut and pull back the rear compartment trim panel.
  4. Remove the wingnuts from the tail lamp assembly.
  5. Remove the tail lamp assembly from the rear body panel.
  6. Disconnect the electrical connector from the tail lamp assembly.
  7. Remove the tail lamp socket by turning counterclockwise.
  8. Remove the side marker lamp socket by turning counterclockwise.
To Install:
  1. Install the side marker lamp socket by turning clockwise.
  2. Install the tail lamp socket by turning clockwise.
  3. Connect the electrical connector to the tail lamp assembly.
  4. Position the tail lamp assembly to the rear body panel.
  5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
  6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
  7. If equipped, connect the cargo net.
  8. Close the rear compartment.
prev.gif next.gif

Oct 18, 2010 | 2001 Chevrolet Impala

1 Answer

How do you replace the tail light bulbs on a 2006 Pontiac Vibe


Tail Lamp: Service and Repair
TAIL LAMP REPLACEMENT
REMOVAL PROCEDURE
1. Open the rear compartment lid.
2. Remove the rear compartment trim panel (4).
3. Disconnect the tail lamp electrical connectors.
4. Remove the following components from the vehicle:
- The 3 nuts (3)
- The tail lamp (7)
5. Remove the following from the tail lamp:
- The stop lamp socket (2)
- The turn signal lamp socket (5)
6. Remove the following from the lamp sockets, if necessary:
- The stop lamp bulb (1)
- The turn signal lamp bulb (6)
INSTALLATION PROCEDURE
1. Install the following to the lamp sockets, if removed:
- The stop lamp bulb (1)
- The turn signal lamp bulb (6)
2. Install the following to the tail lamp:
- The stop lamp socket (2)
- The turn signal lamp socket (5)
3. Install the tail lamp (7) to the vehicle. Secure the tail lamp (7) with the 3 nuts (3).
NOTE: Refer to Fastener Notice in Service Precautions.
Tighten the tail lamp nuts to 10 N.m (89 lb in).
4. Connect the tail lamp electrical connectors.
5. Install the rear compartment trim panel (4) to the vehicle.
6. Close the rear compartment lid.

Oct 30, 2009 | 2003 Pontiac Vibe

1 Answer

How do I remove the cover on a 2002 325i BMW tail light wiring? thanks


Do you need to change a bulb or are you changing to custom lamps. If it is bulb replacement open trunk/boot (depending where you live ) the access for the tail lamps is at the rear corners of the trunk, If you are changing lamp lenses or assembly remove the screws( same location ) at lamp corners

Jul 09, 2009 | 2001 BMW 325

1 Answer

NEED TO REPLACE A TAIL LIGHT BULB IN A 2005 CHEVROLET IMPALA


and Repair Notes TAIL LAMP REPLACEMENT REMOVAL PROCEDURE Open the rear compartment. Remove wingnut and pull back the rear compartment trim panel from the tail lamp. Remove the wingnuts from the tail lamp. Remove the tail lamp from the rear body panel. Disconnect the electrical connector from the tail lamp. Remove the tail lamp socket, turning counterclockwise. Remove the bulb from the tail lamp socket. Remove the sidemarker lamp socket, turning counterclockwise. Remove the bulb from the sidemarker lamp socket. INSTALLATION PROCEDURE Install the bulb to the tail lamp socket. Install the bulb to the sidemarker lamp socket. Install the sidemarker lamp socket, turning clockwise. Install the tail lamp socket, turning clockwise. Connect the electrical connector to the tail lamp. Install the tail lamp to the rear body panel. Install the wingnuts to the tail lamp. Pull back the rear compartment trim panel to the tail lamp and install the wingnut. Close the rear compartment.

Jun 08, 2009 | 2005 Chevrolet Impala

2 Answers

Left rear turn signal bulb is burned out.


Tail Lamp Assembly
Removal & Installation
To Remove:

  1. Open the rear compartment.
  2. If equipped, disconnect the cargo net.
  3. Remove the wingnut and pull back the rear compartment trim panel.
  4. Remove the wingnuts from the tail lamp assembly.
  5. Remove the tail lamp assembly from the rear body panel.
  6. Disconnect the electrical connector from the tail lamp assembly.
  7. Remove the tail lamp socket by turning counterclockwise.

  1. To Install:
  2. Install the tail lamp socket by turning clockwise.
  3. Connect the electrical connector to the tail lamp assembly.
  4. Position the tail lamp assembly to the rear body panel.
  5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
  6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
  7. If equipped, connect the cargo net.
  8. Close the rear compartment.
      Please don't forget to rate !!!!!!

    Mar 28, 2009 | 2002 Buick Century

    1 Answer

    How do i get the cover off the license plate bulbs?


    REMOVAL PROCEDURE
    1. Disconnect the tail/back up lamp harness connector from the from the body wiring harness.
    2. Remove the tail/back up lamp assembly from the rear compartment lid.
    3. While supporting the tail/back up lamp assembly, unplug the tail/back up lamp harness grommet from the rear compartment lid and remove tail/back up lamp from the vehicle.
    4. Remove the license plate lamp bulb from the lamp housing.
    INSTALLATION PROCEDURE
    1. Install the license plate bulb into the lamp housing.
    2. While supporting the tail/back up lamp assembly, install the tail/back up lamp harness grommet to the rear compartment lid and install the tail/back up lamp. NOTE: Refer to Fastener Notice in Service Precautions.
    3. Install the tail/back up lamp fasteners to the tail/back up lamp studs. Tighten Tighten the tail/back up lamp fasteners to 6 N.m (53 lb in) .
    4. Connect the tail/back up lamp electrical connector.
    5. Connect the tail/back up lamp harness connector and clip the connector to the metal edge of the rear compartment lid.

    Feb 25, 2009 | 2000 Buick LeSabre

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    29 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Saturn Experts

    yadayada
    yadayada

    Level 3 Expert

    75051 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7726 Answers

    Are you a Saturn Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...