Question about Ford Fairmont

1 Answer

Could tell me the allthe neccary procedurs and code to change igition switch and key as i have lost mine thanks ron

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,370 Answers

If you get new ignition switch then you get new key with it.But if you want to use your old key then you will have to get your old key reprogrammed by dealer or from local lock smith who deals with car key programming. ----------- To replace ignition switch:--- Disconnect the negative terminal of your car battery.Then remove the steering shroud.the switch is located inside the steering shroud assembly.the shroud and steering are fitted by few screws.Remove those screws.This will separate the steering and shroud.The shroud will come out.First remove upper half and then remove lower half of the shroud from steering assembly. Once this is done.The ignition switch will be easily seen,just remove the screws holding ignition switch and disconnect the wiring harness from ignition switch.There you will see few clips holding the harness. Carefully UN-lock the clips to loosen the wiring harness. the switch is out.Now in the same way reinstall the new ignition switch in reverse position as you removed the old one. ------------------------------- this will help.thanks.Helpmech.

Posted on Dec 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reactivate radio jeep after lock for wrong code


You will need to contact the dealer on this problem.

Oct 28, 2012 | 2004 Jeep Grand Cherokee

1 Answer

Hi my names Trevor. I need to get the lock code from my truck so i can get a new key since i lost mine. I was hoping you could tell me exactly where this lock code is at... Thanks


Hello trevor
The best way to get the correct key made is to remove another lock that the lost key operated and
take it to a locksmith, they will make you a key for about $10.00. Either of the door locks will have
the code stamped on them, or if you have a locking glove box or console that locked with the ign.
key these may have the code stomped on them. Hope this is helpful.

Feb 09, 2011 | 1984 Toyota Pickup Deluxe

1 Answer

I lost igition key


if you have no spare then its a dealer only job to order a replacement but order two keys ,also once you have the keys it has to be programmed by the dealer or a garage with the right software .

Nov 10, 2010 | 2006 Toyota Land Cruiser

1 Answer

Remote got wet in salt water. Had battery changed


Programming
When
Key added or replaced. System malfunction.
How
Driver's door open and key removed from ignition switch. Insert key into ignition switch, then remove it. Within 5 seconds: Insert key into ignition switch, then remove it. Within 40 seconds: Close and open driver's door twice. Insert key into ignition switch, then remove it. Within 40 seconds: Close and open driver's door twice. Insert key into ignition switch. Close driver's door. Switch ignition ON and OFF once to program a new key code whilst retaining the original codes or twice to program a new key code whilst erasing the original codes. Remove key. System should now lock and unlock vehicle, once or twice depending which mode has been selected. Carry out the following button procedure within 40 seconds: Press key lock or unlock button once. Within 3 seconds: Press same key lock or unlock button once. System should now lock and unlock vehicle.
NOTE: If system locks and unlocks vehicle twice, programming procedure has not been completed. Repeat button procedure.
If required repeat button procedure to program remaining keys.
NOTE: To exit programming mode: Open driver's door. NOTE: A maximum of 4 keys can be programmed

This will work providing printed circuit is not damaged in remote

Jul 20, 2010 | 2004 Toyota Camry

1 Answer

2006 Subaru WRX How to change the Security Code PIN


go to an Specialized locksmith , If they have good equipment, they can solve

May 22, 2017 | 2000 Subaru Outback

1 Answer

2005 Monte Carlo wont start after i changed the igition


If its the ignition switch that you changed you need to leave the key in the ignition switch in the on position for about fifteen minutes, it should start after that if not keep repeating until it does.

Oct 24, 2009 | 2005 Chevrolet Monte Carlo

1 Answer

What to know how to tell if ignition key is going bad


Check for voltage to the "start" side of the soliniod. It'll be the little wire. Check voltage from that wire to ground while an assistant turns the key to the start possision. If you don't have 12v, then start working your way back.....asssuming you have a good hot battery w/ good connections and your neutral saftey switch (auto) or clutch switch (standard) are opperational. Jump the switches and see if you have anything then. If not, the it might be the ign switch.

Jun 02, 2009 | 1995 Nissan Pickup

2 Answers

Igition is locked


try getting some lock lube from the hardware store, spray it into the lock, (never use any kind of oil just the graphite powder lock lube) spray the lock lube into the key cylinder and then work the key in and out a few times, if this doesn't fix it u will need a new lock cylinder.

May 20, 2009 | 1999 Chrysler Town & Country

1 Answer

2005 3.7 v6 dodge dakota igition switch


Time for a new ignition switch. This just the switch portion and not the tumbler. You should be able to still use your old tumbler and key. Good luck to you. Thanks for using Fixya!

-JC

Dec 17, 2008 | 2005 Dodge Dakota

3 Answers

1998 audi a4 quattro 2.8


more than likely it is the ignition switch audi actually has an open recall campaign for the faulty ignition switch due to a spring inside the switch stretching causing the key to fail to return to the proper run position. i just did mine yesterday.

Aug 09, 2008 | 1998 Audi A4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...