Question about Smart fortwo

1 Answer

Forward and reverse gears will not engage (engine running ok) 2002

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,098 Answers

Hi

it sounds like the main linkage is bent under the car, being as 1st would be forward and reverse back it is most likely the same linkage doing both jobs and doing both faults. easy reaopir though cost about £100 tops. if the problem is more serious then it could be a new gearbox you need although I would be tempted to say I never had to do that job on this car but I have seen many bent gear linkages.

Regards

Dan

Posted on Dec 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

50 horse 4 stwont go into reverse gear due to shaft problems


the drive shaft just drives a pinion gear in the prop box that drives to gears that spin in opposite directions all the time
by selecting forward with the selector rod , a dog gear is moved forward to mesh with one gear that is turning or moves the other way to engage the other gear that is turning
that is the forward or reverse action for the prop
if you have forward but no reverse the it is not a drive shaft problem but a selector rod adjustment that is not moving the dog far enough to engage the running gear

Jul 08, 2017 | Cars & Trucks

2 Answers

Car will start but put it in gear engine will die


engine starts with no problem; but, when I put in gear and ...

www.cargurus.com > Questions > Hyundai > Sonata

CarGurusNov 15, 2012 - The engine just fall dead when you step on the gas; it seems to jerk before ... My car does the same thing but i put it in neutral n it starts up. ... I have a 2004 kia optima it jerks when I go into reverse it was driving ... start and run fine butwhen I put it in drive or any other gear it dies! ... 2002 Hyundai Elantra GT.

Engine stalls when tranny put in Drive or Reverse - Kia Forum

www.kia-forums.com/kia-carnival...2002.../43407-engine-stalls-when-tr...

Feb 28, 2008 - 10 posts - ‎3 authors
Give it a little gas before putting in D or R and it will go. .... When I start the van cold and shift the tranny into drive or reverse.....the whole front ... won't run in forward gears - Kia Forum
10 posts
May 25, 2012
Intriguing problem - engine rough idle & hesitation ...
10 posts
Aug 31, 2011
2006 Kia Spectra engine stalls and bad idle, cleaning the ...
10 posts
Aug 30, 2010
2002 Kia Spectra Won't Go Out of Park - Kia Forum
3 posts
Oct 28, 2008
More results from www.kia-forums.com

Dec 17, 2015 | 2002 Kia Rio

1 Answer

I have 2005 Chevy Suburban; when you engage the gear in drive the truck would move but won't get out of the first gear. I've checked my transmission fluid and its ok. It also responds to reverse when you...


Common problem probably a 4L60E transmission The low and reverse clutches are the same ones The forward clutches are another set and then there are the 3-4 clutches in another pack. So you probably burn out the forward clutches or could be a stuck valve in the valve body. Time for a transmission specialist.

Feb 02, 2011 | Chevrolet Suburban Cars & Trucks

2 Answers

Could frozen e brakes cause car not to go forward, car moves easy in reverse


No. An emergency brake on the 86 camaro engages the pads against the rotor and the vehicle would not move either in reverse or forward. It sounds like you have a gear problem in the transmission that could be related to either solenoid or actual gear wear. Assuming the vehicle is being MOVED as you say while the engine is running.. thus providing the energy to move it.. Going in reverse has the solenoid engaged one way, drive the other way. Solenoid sounds damaged at this point. Unfortunately this probably will require a transmission rebuild.

Jun 06, 2010 | 1986 Chevrolet Camaro

1 Answer

No Reverse


Check the oil trans filter. Could either be a bad linkage, or a bum synchro. Does it just flat not go into gear, or does it grind when you try to do it? Can you put it in reverse with the engine off?

I dont know exactly witch is you tranny; it sound like you broke the sun shell in the transmission.

For example, this is pretty common with the Chevvorlet 4l60e Transmission, when the sun shell breaks you will lose reverse and fourth gear, the only remedy is to replace the transmssion or have it repaired; the repair will require the transmission be removed and disassembled, you will need to purchase a new sun shell (get a heavy duty replacement) and a papper rubber kit for the repair, just find a good trans guy to provide the labor.

Hope this help.

Apr 06, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Car does not drive forward but works in reverse


Sad to say but your automatic transmission has bit the dust.

Jul 24, 2009 | 2004 Chevrolet Cavalier

2 Answers

Hyundai excel 1996 automatic will engage reverse and park but no forward gears. Gearbox was overhauled 3 years ago, new seals etc. Oil level in the main transmission is ok and no apparent leaks. Problem...


It appears you have a Forward Clutch FAILURE. Replace the trans after you get it diagnosed and verified by a professional technician. By the way, do you have a Check Engine light? If so, what is the diagnostic code? The dealership can scan the system and find any codes which may have been stored in the TCM (Transmission Control Module). If there were any 'Incorrect Gear Ratio" codes, it's most probably the trans itself.

May 16, 2009 | 1994 Hyundai Excel

1 Answer

Reverse engages HARD!!!


Check for trans codes then I would suggest a fluid change if there are no trouble codes, many times these kinds of problems are caused by a little piece of dirt causing a shift solenoid to stick.

Jul 15, 2008 | 1995 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Smart Experts

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

911 Answers

Are you a Smart Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...