Question about 2007 Ford E-350 Super Duty Length XLT

1 Answer

Ford E 350 engine

How to remove the engine and how to replace the engine cooling fan

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

The only way to get this engine out is to remove the front grill ,core support, radiator, etc.

Posted on Mar 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I take the AC compressor off of 97 Ford Econoline 350


In my opinion the easiest way to remove the compressor is to remove the cooling fan and shroud. I'm guessing this is a gas engine? Recover the refrigerant, disconnect the a/c lines. drain coolant. Disconnect upper radiator hose. r&i the air cleaner. Using a fan clutch tool or and air chisel to loosen fan remove fan and shroud. Remove the belt. One bolt is a 13mm holding the compressor, the other two are 10mm . Remove bottom splash guard to gain access to the compressor on the bottom of the engine passenger side of van. The manifold line is held on with a 10mm bolt. Reverse procedure to install. Good luck.

Nov 12, 2015 | Ford Cars & Trucks

1 Answer

95' ford econline 350 van replacing waterpump and clutch fan how to replace.


TO REPLACE WATER PUMP.REMOVE THE RADIATOR SHROUD HALVES.REMOVE FAN CLUTCH AND FAN.YOU NEED FAN CLUTCH WRENCH AND A FAN CLUTCH PULLEY HOLDER.YOU CAN RENT TOOLS AT AUTO ZONE OR BUY THEM AT A AUTO PARTS STORE.THE FAN CLUTCH BOLTS ARE LEFT HAND THREAD. REMOVE THEM BY TURNING CLOCKWISE.BEFORE INSTALLING NEW WATER PUMP COAT BOTH SIDES OF WATER PUMP GASKET WITH GASKET SEALER.TORQUE WATER PUMP BOLTS 18 FT LBS.

Mar 15, 2011 | 1995 Ford Econoline

2 Answers

1999 chevy tahoe 5.7L vortec 350 new thermostat,new radiator,new waterpump.still overheating?


REPLACE RADIATOR PRESSURE CAP AND CHECK THE COOLING FAN CLUTCH.WHEN YOUR ENGINE HOT WHEN YOU TRY TURNING CLUTCH FAN WITH YOUR HAND WHEN ENGINE IS HOT.THERE SHOULD BE RESISTANCE IN THE FAN.IF CLUTCH FAN SPINS FREELY WHILE ENGINE HOT.YOU NEED TO REMOVE COOLING FAN TO REPLACE CLUTCH.

Feb 23, 2011 | Chevrolet Tahoe Cars & Trucks

2 Answers

2002 jeep grand cherokee larado is over heating. The cooling fanonly runs if I hotwire it. I changed th thermostat. Temp gauge is reading . Could it be the cooling fan relay if so where is it located. The...


Fan relay is located under pass headlight. Remove light assembly, use 2 1/2 " hole saw to drill hole in plastic housing ,3"from back wall, 3'' from left side.This will put you right over relay. Unscrew two bolts,replace. Relay was $40.... dealer wanted$350 to remove front bumper to replace it.

Sep 02, 2010 | 2002 Jeep Grand Cherokee

1 Answer

How to replace the water pump on a 1998 e150m 5.4l ford van


Remove the cooling fan and fan shroud. Remove the serpentine belt, and water pump pulley.

Remove the water pump. Its fairly straight forward. Only hard part is your leaning down into the engine bay.

Jul 02, 2010 | 1998 Ford Econoline

1 Answer

How do you install a water pump in a ford f 450 6.0 ?


6.0L Diesel Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. With the vehicle in Neutral , position it on a hoist.
  3. Remove the radiator and shroud assembly.
  4. Disconnect the cooling fan electrical connector. Unclip and position the fan wiring aside.
    NOTE Use a hole in the fan hub to prevent the fan from turning.
  5. Using the hub tool, loosen the cooling fan and clutch.
  6. Remove the cooling fan assembly.
  7. Remove the stator bolts and the stator.

    8ac47ee.jpg
    Fig. Remove the stator bolts and the stator-6.0L Engine
  8. Rotate the accessory drive belt tensioner clockwise and position the drive belt aside.
  9. Remove the bolts and the coolant pump pulley.
  10. Remove the bolts and the coolant pump.
  11. Remove and discard the O-ring seal.
  12. Clean and inspect the coolant pump mounting.

    3ed0f4d.jpg
    Fig. Water pump mounting-6.0L Engine
  13. To install, reverse the removal procedure.
  14. Observe the following torques:
    Stator bolts: 30 ft. lbs. (40 Nm) Pulley bolts: 23 ft. lbs. (31 Nm) Water pump bolts: 17 ft. lbs. (23 Nm)

Hope this help.

May 15, 2010 | 2005 Ford F 350 Super Duty

1 Answer

Want to replace the radiator on my 1997 ford thunderbird


Radiator Aluminum Core, Crossflow — 3.8L (Base) and 4.6L Engines
Removal
  1. Drain engine cooling system as described. Disconnect upper radiator hose (8260) and lower radiator hose (8286) and radiator overflow hose (8075) from the radiator (8005). Disconnect the transmission oil cooler inlet and outlet lines from the radiator.
  1. Remove cooling fan motor,fan blade (8600) and fan shroud (8146) assembly as described.
  1. Remove radiator upper bracket retaining bolts and remove bracket. Lift radiator from vehicle.
Installation
  1. Position the radiator into the vehicle. Install upper brackets and tighten bolts securely.
  1. Connect the transmission oil cooler lines to the transmission oil cooler fittings.
  1. Install cooling fan motor, fan blade and fan shroud assembly as described.
Engine Cooling Fan Motor, Fan Blade and Fan Shroud Assembly, Electrical Removal
  1. Disconnect (pull apart) the male-female cooling fan motor wiring connector at the side of the fan shroud (8146). Remove the male terminal connector retaining clip from the fan shroud mounting tab.
  1. Remove two fan shroud upper retaining bolts at the radiator tanks.
  1. Lift cooling fan motor/fan blade (8600)/fan shroud assembly past radiator (8005), disengaging fan shroud from two lower retaining clips.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten fan shroud retaining bolts to 5.2-7.2 Nm (46-63 lb-in).

  2. 10e2638.gif
    8d231fe.gif HOPE THIS HELPS.

    Oct 30, 2009 | 1997 Ford Thunderbird LX

    1 Answer

    Need to replace Radiator on a 95 F-350 (7.3 l) turbo diesel,


    if the radiator cools properly and engine does not overheat, I would probably change the antifreeze solution but not the radiator, does it leak? test its cooling capability by running the engine until the cooling fans operate. changing the fluids is a good idea, also lube driveline and suspension

    Mar 31, 2009 | 1995 Ford F350

    1 Answer

    1989 ford f-350 7.3L water pump replacement


    DONT REMOVE THE PULLY!! ITS SPRING LOADED!!!

    yes, take out the shroud.

    no, you dont have to have the belts on to replace the water pump.

    Feb 15, 2009 | 1989 Ford F 350

    Not finding what you are looking for?
    2007 Ford E-350 Super Duty Length XLT Logo

    Related Topics:

    137 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    74544 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22082 Answers

    fordexpert

    Level 3 Expert

    5433 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...