Question about 1995 Ford Bronco

1 Answer

Help 1995 ford bronco turns off when you put it on drive/Low2 but works reverse and Low 1

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 674 Answers

You have a wiring problem in the steering colum take the cover off the colum and and look around the shifter and the wires there you will see what is moving and you should find a shorted wire.

Posted on Aug 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my truck die when I put it in drive


Stalls when put into Drive or Reverse - Ford Truck Enthusiasts Forums

www.ford-trucks.com > ... > 1987 - 1996 F150 & Larger F-Series Trucks
May 22, 2012 - Stalls when put into Drive or Reverse 1987 - 1996 F150 & Larger ... the fluid that was needed...my truck would stall when I shifted into reverse. 1995 Bronco stalls when put into drive
Jun 13, 2013
ford powerstroke truck dies in reverse
Oct 29, 2011
Truck dies when putting in gear and giving it gas.
Feb 26, 2011
ENGINE IDLES FINE,DIES WHEN PUT IN DRIVE
Jun 26, 2010
More results from www.ford-trucks.com

TRUCK DIES WHEN PUT IN REVERS


Nov 30, 2015 | Cars & Trucks

1 Answer

We can get the 86 bronco II to start and run but will not go when put into drive or reverse?


Check your Transmission Fluid. If it is low fill to the recommended level. If it smells burnt it is time for a Rebuild.

May 14, 2014 | 1986 Ford Bronco II

1 Answer

1995 Ford Bronco engine dies when shifted into drive but runs in reverse or 1st gear


Could be fuel filter,air filter,tune up,wires,coils.low idle too low.

Jun 13, 2013 | 1995 Ford Bronco

1 Answer

I have a 1995 Ford Bronco with Push Button 4X4 with automatic locking hubs. Has a 351 engine. The problem I have is when you push the button to engage 4X4, the front tiers to do not pull on either high or...


It sounds like your front hubs are worn out. Actually just 1 of them. You can put in 4 high or low pull it forward chock it raise the frnt wheels to see which one isnt locking by turning it. Most people just go ahead and buy new set of manual Waren lockers.

Jan 17, 2011 | 1995 Ford Bronco

1 Answer

Transmission?


This issue sounds like dried seals. it is unlikely a filter issue, but no reason to exclude that. Ford uses coarser screen, and does not plug as often.
Consider "mechanic in a can" transmission conditioner, aiming to revive seals.
In any event, the unit may be happier after running some miles.
If that does not work, it is trans surgery time.

Jul 28, 2010 | 1989 Ford Bronco

1 Answer

Reverse works good, when you put it in drive you have to reev it up to get it to pop into gear and it jumps, any suggestions???


Try checking the transmission oil level, as if it is low it will be struggling to fill up the torque converter

Feb 08, 2010 | 1987 Ford Bronco II

1 Answer

1993 Bronco 5.8L, dies in reverse, and in low forward


not sure on your year but check the modulator on the transmission. remove the vacuum line at the modulator and see if there is any tranny fluid there. if the there is change the modulator.

Jan 15, 2010 | 1993 Ford Bronco

1 Answer

The issue is that, after driving the bronco for a while...maybe 20 mins or so with AC on, when i try to park and need to reverse, or if i brake too hard, the car dies, and i have to turn the key and...


what year of bronco, fuel injected or carb ? check for a vacuum leak with the powerbrake booster, by you explaination it seems the common thisng is your foot on the brake pedal...please rate my help, thanks

Aug 05, 2009 | 1995 Ford Bronco

1 Answer

Won't come out of 4 low and won't change from 1st to 2nd gear


try checking your auto trani fluid... and with the 4 wheel drive try puting ti in nuteral and if the doesnt work try puting it in reverse and back up after taking it out of 4 wheel drive.

May 24, 2009 | 1996 Ford Bronco

Not finding what you are looking for?
1995 Ford Bronco Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...