Question about 2000 Mercury Villager

3 Answers

Rear seat removal 2000 merc Villager

How do you remove the back seat in a 2000 Mercury Villager

Posted by on

  • 4 more comments 
  • stevejanemc Jul 07, 2008

    Thats the same thing I ran into...we are going to remove the tracks and seat permanently...we have no use for the rear seat so that works for us...thanks

  • Anonymous Mar 18, 2014

    2000 mercury villager thermostat housing

  • Anonymous Mar 18, 2014

    Remove back seat

  • Anonymous Mar 26, 2014

    How to remove speakers

  • Anonymous Mar 27, 2014

    windows seats and locks stop working

  • Anonymous Mar 27, 2014

    power seats power windows power locks stop working

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Mercury Master
  • 1,224 Answers

Fold top seat down first
then there is seat clip push seat forward with upward motion
this releases back floor clamps once released pull seat back this releases the front clamps then pull seat out of back door

Posted on Jul 07, 2008

One time only. The rearmost bench seat is dismounted with six large machine screws (and one phillips head screw) but the problem is the slides that the seat is attached to. The slides are apparently installed with the rails in one piece and cannot be removed from it without violence. Once the bench seat is removed from the slides, I found the easiest and least distructive way to remove the slides is to pull up the carpet at the back end of the rail and cut off two sheetmetal stops that close off the back end of the rails. Once the channel is open, the slides can be forced off of the back end of the rail using a heavy hammer and a flat bar to get it over the rear doorr seal. The carpet tucks easily back into the molding. 

Posted on Aug 31, 2008

  • tony carl
    tony carl Jul 15, 2014

    i found all 6 bolts but cant find the phillips head screw...where is it?

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

We have a 1997 Mercury Villager. I don't know how different it is from ours. We cannot remove the back seat. We can remove the middle seat and slide the back seat forward. I hope this helps.

Posted on Jul 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove rear seat 2002 mercury villager?


Under the seat there are a couple levers move them in opposite direction and see if the seat will move away from the bar it latches to.

Feb 15, 2015 | 2002 Mercury Villager

1 Answer

Are we able to remove the 3rd row seat in the 98 Merc Villager?


Look for the bolts (under the carpet) & remove them, should come right out.

Aug 15, 2014 | 1998 Mercury Villager

1 Answer

2000 mercury villager - how do you remove the rear wiper arm from the shaft?


you just depress the little release tab and pull it off. Most need soaking in penetrating oil for at least a week. PB Blaster is best stuff.

join the group

http://groups.yahoo.com/group/villagerquest/

gerry

Feb 24, 2011 | 2000 Mercury Villager

1 Answer

My son pulled out and then snapped back the rear passenger side seatbelt on my '99 Merc. Villager Van, and it ended up locked into place near the floor inside the mechanism used to adjust the rear bench...


is the belt wrapped around the lever to adjust the seat?
Try sliding the seat to get some slack.
He may have it in ALR mode. That is when you pull it allthe way out, and then it ratchets it's way back in until it is all the way in. Then it reverts back to pulling out and going in w/o ratcheting.
This is to lock a child seat in.
So, you need to get it in all the way somehow.

go here for more help.

Gerry

http://groups.yahoo.com/group/villagerquest/

Apr 05, 2010 | 1999 Mercury Villager

1 Answer

How to remove the back seat from my 1998 Mercury Villager


it is not designed to be removed. It is designed to slide back and forth as needed.

Section 01-10: Seats and Tracks 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Seat, Rear Bench
Removal
  1. Remove the center seat(s) if equipped. Refer to the procedure in this section.
  1. Slide the bench seat forward to the center row seating position.
  1. Use a flat-blade screwdriver to remove the cover caps from the front of the rear seat cushion latch cover.




  1. Remove the two rear seat bolts from the front of the rear seat cushion latch cover.




  1. Lift the rear seat cushion floor cover on the back of the rear bench seat and remove the two inboard rear seat bolts and the two outboard rear seat bolts.




  1. Remove the bench seat from the vehicle through the body side door opening.

Apr 30, 2009 | 1998 Mercury Villager

1 Answer

The seat belt gets stuck and makes a loud and distracting noise


The system can be operated manually by removing round cover cap on the B pillar (Just behind door). manually turn crank knob on top of motor.

There is a limit switch on the A pillar to turn off the motor for forward movement. There is a limit switch on the B pillar to shut off the motor for rearward movement.

You may need a B pillar limit switch if the belt is going all the way back but not shutting off. Unfortunately the rear limit switch is serviced with the track & motor assembly. Get a used one at car-part.com. Page with * is cheapest part.


You need to remove A pillar trim, B pillar lower trim, B pillar upper trim, and front door opening upper trim.

disconnect front limit switch
disconnect rear limit switch
disconnect motor electrical connector
remove 3 motor bolts
remove 2 limit switch bracket bolts
remove screw at A pillar near limit switch
remove 3 screws at track assy to roof.
pull back carpet & remove 4 screws at floor where you step into car.
remove track & motor assy.

Apr 10, 2009 | 1993 Mercury Villager

1 Answer

Removing middle seats-procedure


in owner manual.

there are 2 release handles on each seat at front. pull up on them and then rock the seat up at the front. then slide the seat rearward to slide the "U" hooks out of the bottom slots.

Mar 29, 2009 | 2000 Mercury Villager

5 Answers

Mercury Villager headlight assembly diagaram for removal


This is easy. Lift the lid open. Look at the back of the sealed beam and you will see a clip and an o ring. Pull the clip up and pull wires back toward the driver's seat. Unscrew the o ring and firmly pull the bulb out toward the driver again. Note the 3 tabs on the bulb seat and realign the new bulb with those tab ( 2 bottom, 1 top). Replace with #9007 bulbs..do them both.

Jul 01, 2008 | 1995 Mercury Villager

Not finding what you are looking for?
2000 Mercury Villager Logo

1,790 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...