Question about 1996 Jeep Grand Cherokee

1 Answer

Won't start already replaced ignition coil and distributer and still no turn over...

Posted by on

  • Anonymous Jul 14, 2008

    I have a 1996 jeep grand cherokee and had the same problems. I replaced the coil and distributor but still had problems. Finally I replaced the computer with a used computer from a salvage yard and the problem was solved.

×

1 Answer

Have the computer checked out

Posted on Jul 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car don't want to start, replace coil & distributor already, still the same result


Did you test first ? check for power B+ at coil , Does it have a crankshaft position sensor , an ignition control module ? Is there spark ? pull the coil wire an hold near ground ,is there spark ? What make ,model an year vehicle do you have ? Is the distributer in right , not 180 degrees out of time !

Sep 10, 2015 | Cars & Trucks

1 Answer

1988 ford bronco11 have feul,but no fire from distributor to coil


with distributer cap off have someone crank engine and see if your rotor is turning if not repair distributer or replace.

Apr 05, 2014 | 1988 Ford Bronco II

1 Answer

Dodge Avenger 96 2.0L Won't Start


my wife had a 96 chrysler cirrus with the 2.6 v6 engine. the distributer was under the intake manifold and had the cam position senser in it. this is the hottest area in the engine, very bad engineering, replaced the distributer four times, each one averaging four months, spent $2500, finally sold car and would never buy another chrysler product.

Mar 12, 2013 | 1996 Dodge Avenger

2 Answers

Saturn won't start it cranks but won't turn over. There is no fire between the coil paks and spark plugs but can't figure out why


Someone would need to check for power and ground at the coils and that the timing belt is ok.

Dec 06, 2012 | 2001 Saturn SC

1 Answer

Won't start, not spark from coil


its maybe bad or the ignition module has issue-----chec inside of distributer cap for buildup--------test plug wires

Jun 17, 2012 | 1992 Toyota Pickup

1 Answer

1991 Honda crx won't start


Try tracing the wires and looking for a worn spot in insulation that is grounding out, its a royal pain but might be the only solution, use wire prob and test areas where inaccessible. good luck

Jun 09, 2012 | 1991 Honda CRX

1 Answer

I have a 91 olds supreme 3.1 v6 it shut off and won't start back .... It starts but won't turn over.... And when turn the key back off it's blows the dis fuse wich mean direct ignition system...


Check the coils that have been replace for bent or broken prongs that plug into the ignition control module and if nothing looks damaged then i would think the ignition control module is faulty.Replace ignition control module.

Jan 21, 2012 | 1991 Oldsmobile Cutlass Supreme

1 Answer

85 dodge 360 no spark replaced, coil , ign switch, condesor , replaced distributer , wires, plugs , coil is getting power to it at 13.3 volts


I would suspect the ignition control if you have already replaced all that stuff. I personally would replace it with an MSD ignition for better running and fuel mileage, but the ignition module should be a whole lot cheaper.

Jul 14, 2009 | 1985 Dodge Ram 3500

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...