Question about 1996 Ford Windstar

1 Answer

Transmission code 743

Posted by on

  • 1 more comment 
  • ts6019 Jul 06, 2008

    transmission code po743

  • ts6019 Jul 06, 2008

    code po743

  • ms_ariadna Feb 17, 2009

    my car gives me the codes po743,po750,po755 is it hard to fix or expensive


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 321 Answers

PO743 definition is "TCC circuit Error".TCC stands for Torque Convertor Clutch.The diagnostic route for that code includes ohms testing,amps testing,and function testing the solenoid and the wires in the circuit.

Posted on Jul 10, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

P0743 code

Code 743 is for the torque converter circuit.
The problem could be the torque converter itself or the wiring-solenoid going to it.

Feb 13, 2014 | 2001 Ford Taurus

1 Answer

How to fix this problem ?code#po743 2000ford taurus se 3.0

Code 743 means the computer did a volt drop test on the circuit and found the solenoid to be open or shorted to ground. It could be the solenoid valve, or the wiring.

Jun 25, 2013 | Cars & Trucks

1 Answer

02 explorer dtc p 0743 and p 0745 and od light flashes how to fix

Code 743 is for a problem with the torque converter clutch or circuit, and code 745 is for a problem with the pressure control solenoid.
Those two components are inside the transmission and would need to be tested by someone with the necessary tools and repair procedures.

Mar 06, 2013 | Cars & Trucks

1 Answer

Engine fails to start

joe2mercs 743 Solutions May 28, 2010
First check for any cracked pipes leading into the intake manifold If all OK (with no codes showing it probably is OK) try checking the fuel pressure regulator. If you smell fuel from the pressure regulator vacuum side arm (when the vacuum line has been disconnected) it needs to be replaced.

Mar 04, 2013 | 2001 Chevrolet Malibu

1 Answer

Jeep trouble code 320 and 743

One problem at a time please. Let's get the engine running All the time! First, it seems that the battery is weak, perhaps old and past its prime (thus the jumper cables worked). Or, maybe you just need to clean off the battery terminals on the battery and the connecting cables. When did you replace the plugs, wiring harness, distributor cap and rotor last? Perhaps just cleaning them up will do the trick. Also, check that the grounding cables all over the engine compartment are clean and tight.

Jan 13, 2013 | 2001 Jeep Wrangler

1 Answer

Igot these for codespo443 p1747 po755 po750 po743 po113

P0443 Evap purge control
P1747 Pressure control "A"
P0755 Shift solenoid "1" malfunction
P0750 Shift solenoid "A"
P0743 Torque convertor clutch circuit
P0113 Intake air temperature high input
For now leave the P0443 that is a evap code. for code 755 750 743 how did you get these code? clear it do key on engine running. the reason I say this is somewhere especially at the tranmission harness you are somehow disconnected. Check the transmission range selector switch closely, inspect the harness and do a wiggle test on the wires. some how your wire are disconnected

Feb 26, 2012 | Cars & Trucks

1 Answer

Oil leak at the rear of the valve cover on the right side does not appear to be the valve cover gasket. another issue is the check engine light and the code is 743 and the o/d off light is blinking.

This isn't a solution, but I have a similar oil leak. I can see clearly with the help of a telescopic mirror that the leak is emanating from the port where the PCV valve hose goes into the cylinder head.

Oct 20, 2010 | 1998 Mazda MPV

1 Answer

I have a error code reading of PO 743, Torque converter clutch, what does that mean?

It sounds like the convertor in the exhaust system is partly blocked. You will need to have this checked at a shop. Frankster016

Oct 26, 2008 | 2000 Ford Expedition

Not finding what you are looking for?
1996 Ford Windstar Logo

Related Topics:

536 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

69114 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Ron Lankford

Level 3 Expert

5383 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides