Question about 1995 Jeep Grand Cherokee

1 Answer

How to access front turn signal for replacement

Cannot figure out how to replace my broken front turn signal assemblies.

Posted by on

  • 1 more comment 
  • ferlie Jul 22, 2008

    Need to know how to replace the plastic housing that holds the turn signal bulb.

  • Justin Case
    Justin Case May 11, 2010

    Are you referring to the signal lamps or turn signal switch?

  • Scott Ackerson
    Scott Ackerson Apr 27, 2014

    lamp

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,498 Answers

Here you go, removal & installation of:

Front Parking/Turn Signal Lights:

  • Remove the screws from the the lens and separate the lens from the bezel
  • Remove the screws from the turn signal housing and pull it out
  • Turn the bulb socket CCW 1/3 turn and remove it
  • Installation is the reverse of this procedure
Side (Front) Marker Lights:
  • Remove the screws from the marker lens
  • Separate the lens from the headlight
  • Pull the bulb from the back of the lens
  • Installation is the reverse of this procedure
Hope this helps

Mike

Posted on Jul 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I access the front drive side turn signal to replace the bulb on a 2003 Discovery?


You need to access phillips screw next to top right side of driv headlight and slide turn signal assembly forward. It helps if you remove black plastic access plate above headlamp.

Feb 28, 2011 | 2003 Land Rover Discovery

1 Answer

Need to replace turn lamp on left front (dash message). I have replaced rear turn lamps, but cannot see how to access the turn lamp area in the front. In the rear a couple of bolts held the whole rear lamp...


Welcome to FixYa.com

Park and Turn Signal and Daytime Running Lamp Nuts (Qty: 3)

Tip

Disconnect the forward lamp harness connector from the lamp socket



leedavidian_239.jpg


Thank you for using FixYa.com

Regards, Lee Davidian

Jan 12, 2011 | 2006 Chevrolet Uplander

2 Answers

How do you replace the front turn signal on a 2005 Buick Terraza?


Changing front, right turn signal on 2005 Buick Terraza: Open hood; when facing the front of vehicle, the right turn signal is on the passenger side (left). The headlight assembly needs to be removed to easily reach the turn signal. On my vehicle, there is a 10 mm screw on the left side. Remove it. There is L-shaped pin on the right side of the headlight assembly. Swing the pin counter-clockwise (to the left). Pull the pin straight up to remove. The headlight assembly is now loose, but there is a pin snapped in a socket on the back of the assembly that still holds the assembly. Pull the headlight assembly hard and straight to the front of the vehicle. When it snaps loose, the assembly is now held just by the rubber gasket surrounding the assembly. You need to gently work the right side of the gasket out of the grill cowling. The assembly should pull straight out. The wires are long enough to lay the headlight assembly in the engine compartment. Finally, the turn signal is now accessible. Twist the light holder counter-clockwise and pull out the light holder. Change the bulb. Do not punch your man-card for credit until you have successfully reinstalled the headlight assembly. It goes back in a little easier the second time. Once you have put the L-pin in place, the screw back, and successfully tested the lights, you can now punch your man-card.

I give the mechanical engineers and designers a D-minus instead of an F only because I was successful on the first try. No light bulb on anything commonly used by people should be this hard to figure out.

Sep 07, 2010 | 2005 Buick Terraza

1 Answer

Need to repair front turn signal(upper) how do i access it?


if it is the turn signal in the front bumper all you need is a screw driver to take the whole light piece out, then replace the bulb

Apr 26, 2009 | 1998 Mitsubishi Montero Sport

1 Answer

How to access and replace turn signal bulb?


Remove the headlamp assembly, and replace the bulb. Should be one or two bolts on the top holding it in, then a couple of push joints to pull out.

Mar 08, 2009 | 1998 Dodge Grand Caravan

1 Answer

How do I replace the front turn signal light?


the bolts are or should be accessable from underneath behind the sheet metal

Jan 26, 2009 | 1997 Geo Prizm

1 Answer

Replace front turn signal light bulb on 1998 Buick Park Avenue


should be plastic clips holding it up...
if not let me go to the junk yard and look at a park ave...I know all buicks but this one is blank in my mind.

Dec 24, 2008 | 1998 Buick Park Avenue

1 Answer

I can't figure out how to replace the front turn signal


There is one screw on top of headlight assembly that holds turn signal lens in place you have to remove that screw and pull lens straight out. As far as head lamps go its just a matter of getting your hand behind headlight assembly to remove the collar that holds the bulbs in place.

Nov 11, 2008 | 2000 Honda Accord

2 Answers

Replace the front turn signal light bulb


you have to go under the front of the car. very easy to fix.

Oct 21, 2008 | 1998 Chevrolet Blazer

1 Answer

Rear turn signal light bulb replacement


Yes, and easy access from the trunk. You will be able to remove the bolts from inside and the light assembly will be able to be pulled from the externior to replace all of them. It is not a real quick process, so when one goes out, I usually replace all of them.

Jul 23, 2008 | 1992 Toyota Celica

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

611 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...