Question about 1999 Isuzu VehiCROSS

1 Answer

Front Axel The front axel of my 1999 Isuzu VehiCROSS will not pull out of the third member. Is there something I should know about getting it free or can it get locked in somehow?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Isuzu Master
  • 450 Answers

You have to undo inner cv boot and remove clip inside cv then pull out outer cv with shaft and inner bearing of inner cv,leaving inner cv outer section in diff.If you want to get out inner cv end, diff assembly must come out of vehicle then unbolt plate retainer on diff tube.

Posted on May 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 rodeo front axel is locked in gear


this is part time 4wd
drive to dirt and deselect 4wd,
do not engine PT 4wd on dry pavement or risk damage to drive line
RTM read the manual in the glov e box.
the do's and don'ts

Jul 07, 2014 | 2000 Isuzu Rodeo

1 Answer

If you pull the cable to engage the front axel how do you dis engage it


This is done by a switch on the dash, if is an S10. It is electronic switch.

Mar 23, 2014 | 1995 Chevrolet Blazer

3 Answers

How to replace a front wheel hub assembly on a 1999 blazer 2wd


remove tire
remove axle nut
remove 3 bolts holding hub in
sometimes may need to hit hub with hammer after all bolts out to get it to release

Dec 22, 2010 | 1999 Chevrolet Blazer

1 Answer

Front axle asembly


I guess you'd like to remove the CV axel to change it? The axels acan be bought rebuilt or new for almost the same price. Auto prts ctores should have them in stock or get them in one day. Less than 50 for rebuilt and about 70 or less for new. They come with purchaser lifetime warrentee. bothe rebuilt and new the rebuilt one you need to take the core back as it might cost 60 or more or bring the old one with you. With the car jacked up and the wheels removed from the frount remove the cotter pin and the keeper from the front axel retaining nut and remove the nut it's a big one 1 3/16 inch and turn it off with your 1/2 inch air impac gun that'll hit at leasest 450 LBs/ Touque. If you don't have this tool take the car to someone that does. Remove the two bolts that hold the lower ball joint tot he lower control arm 17MM headed the same 1/2 air impac takes them out too. With a long iron bar pry the lower control arm down, you may have to smack it with a hammer to get it loose, pull the steering knuckle ( the break and rotor assembly) out and back and pust the axel out of the hub as you pull the steering knuckle back take care as to not pull the break hose too far but it's long enough to get the axel out. by pass the pused aside steering knuckel and pull the axel out of the trans. You might have to pry it out..The passenger side takes a little more doing as it has a carrier bearing bolted to the back of the block of the engine that has to be removed and a bracket that's bolted to it as well. with the carrierbearing free of the engine this axel with the steering knuckle pulled aside pulls right out no prying.

Dec 12, 2010 | Toyota Tacoma Cars & Trucks

1 Answer

1997 isuzu rodeo front CV shafts ,how to separate from pumpkin


The axel should just snap in a good sharp pull should remove it.

Nov 30, 2010 | 1997 Isuzu Rodeo

2 Answers

Cannot locate TCM on 99 Isuzu Vehicross


try under the front seat or kick panels

Jul 09, 2009 | 1999 Isuzu VehiCROSS

1 Answer

1999 dodge cummins 2500 front axel seals


you need to pull off wheels,brakes, rotor /unit hub bearing, both axles and intermediate shaft, as well as the vac disconnec ton the front axle tube. if only the right side leaks then only then only pull the right axle and intermediate shaft and vac disco. it is a trick with a miller tool to replace the seal. the left side seal is inside the diff and the carrier has to come out to replace it. pete

Jun 09, 2009 | 2004 Dodge Ram 2500

1 Answer

Just in an accident, how much is an axel


You would need to get in touch with your local recycling yard, as prices vary from place to place. buying new would be HELL to find, and expensive. it may not hurt to call a dealer.

Feb 27, 2009 | 1999 Dodge Caravan

1 Answer

Need to remove front right axel,


It will take some time, but you will have to unbolt the wheel, then find your sway bar, it should be a small bar/rod that comes up and connects to a larger one, then you will take the bolts out from the bottom of the strut. Make sure you have the car on a jack stand in the front unless you have two jacks, b/c you may need a jack to lift the hub assembly back up to mount the strut.......Once you have basically disconnected everything from your hub assembly and it is hanging/moving up and down freely, (make sure you don't damage the brake lines in the process, move them safely) you will grab the top of the rotor, and pull toward you and down, then basically it is just some pulling, and pushing before you get the shaft out.

Feb 14, 2009 | 2001 Toyota Camry

Not finding what you are looking for?
1999 Isuzu VehiCROSS Logo

Related Topics:

414 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...