Question about 2001 Chevrolet Blazer

1 Answer

Crank w/ no start

Blazer died while driving on freeway. there is fuel at test port during cranking and spark to plugs. Have you heard of timing chain snapping on these?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 702 Answers

I've never seen a timing chain break on these engines.What you may have is either a dirty connection at the crank sensor or the crank sensor is bad. The cranks sensor tells the fuel system and ignition to work in synch.

Posted on Jul 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Engine died while driving on the freeway, now only cranks but wont turn over/


As with any no start problem, have you checked for spark at the plugs and normal fuel pressure at the injectors ?
Does it crank with normal compression ?

Mar 08, 2015 | 1996 Toyota Corolla

1 Answer

While drviing down freeway today the 2.5 ltr engine died and will crank but will not start. one month ago it was backfireing in intake and dieing on freeway and i thought i had bad gasoline it fixit


you need three main conponents for the engine to run,fuel,spark,compression . first have someone to crank the motor and put the spark plug lead of the plug and hold it near the block and if there is spark it will jump a inch or so, check the fuel filter , hold the fuel line clear of electirical and heat, crank engine , fuel will flow, when engine is running but running rough as a miss fire disconnect plug lead one at a time till you find missing cylinder

May 07, 2012 | Jeep Cherokee Cars & Trucks

3 Answers

While driving in freeway the engine turned off on my 95 cadi and


Could be gas related, could be ignition spark related. you will have to troubleshoot to find if spark is at plugs in the right time and sequence. also, you will need to know if you are getting fuel to your cylinders. Can't help anymore without being there first hand.

Jul 16, 2009 | 1995 Cadillac DeVille

2 Answers

My 1995 blazer will not start


Have you changed the module in the distributor?

Mar 21, 2009 | 1995 Chevrolet Blazer

1 Answer

NO SPARK!


The crank and or the cam sensor has failed. If you have no way of pulling codes or checking for signals from the sensors, start with the crank sensor, its more common.

Feb 08, 2009 | 1997 Chrysler LHS

1 Answer

98 ford windstar died during test drive after spark plug change


i would think the coil is bad and i would replace it.

Dec 17, 2008 | 1998 Ford Windstar

2 Answers

Cranks but wont start


Engine Cranks But Will Not Start

For an engine to run, you need three things to happen inside the engine. Compression, fuel and ignition, without any one of these components the engine will not run.
Basic Checks:

A. Test Fuses. Test both under hood power distribution center and the fuse panel under dash. This is done with a test light tool. The test light should illuminate on both sides of the fuse, if not the fuse has failed and needs to be replaced.
B. Testing Fuel Pressure Test for proper fuel pressure with a test gauge on the fuel rail, most throttle body injection cars (TBI) are between 13 psi and 17 psi. and most (DPI) direct port inject systems are between 40 psi and 55 psi. If no or little fuel pressure is observed and there is 12 volt power present the fuel pump, the fuel pump needs replacing.
C. Checking Timing Belt Test for compression by removing a spark plug and insert a compression gauge. Crank the engine over about 5 seconds the gauge should read between 125 psi and 165 psi, if no compression is observed remove front engine cover to inspect timing belt or chain. Crank engine to observe cam rotation, if the cam does not rotate the timing belt or chain has failed. (note: if the timing belt drives the water pump it is best to replace the water pump at this time)
D. Test for Injector Pulse Remove injector connector to insert injector test light (node) or volt meter. Observe light flash or gauge pulse while cranking. If light/voltmeter doesn't respond, an ignition distributor/crank angle sensor (CKS) or an ignition module is most likely your problem.
E. Test for Ignition Spark Remove spark plug wire, insert an extra spark plug into end of wire, rest spark plug next to a ground source then crank engine. You should observe a blue spark between the spark plug gap and ground source. If no spark is observed, an ignition coil, ignition rotor or spark plug wires might have failed. (always keep hands away from engine when cranking)

Jul 14, 2008 | Hyundai Motor 2002 Sonata

Not finding what you are looking for?
2001 Chevrolet Blazer Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...