I can not start the engine cause the key is in lock mode, i can't seem to turn the keys in order to start it. please help

Door Key Switch
The BCM monitors the door key switches in order to disarm the CTD system. When the lock cylinder turns in order to unlock the door, the switch grounds the disarm input to the BCM.
The key lock input to the BCM is probably missing , BCM doesn't see it . So it think's your breaking into the vehicle. Did you try the passenger door to see if it will disable the alarm .
The BCM - body control module ! Electronic -computer !
--------------------------------------------------------------------------------
Content Theft Deterrent (CTD) Does Not Disarm with Key Lock

The factory service repair manual has a 23 step diagnostic procedure . An you would need a factory scan tool to find the correct fix.
Turn ON the ignition with the engine OFF.
With a scan tool, observe the door key switch parameter in the Body Control Module (BCM) security data list.
Does the scan tool display INACTIVE?

Locking the Vehicle Without Arming the System
Use one of the following procedures in order to lock the vehicle without arming the system:
• Procedure A -- Lock the vehicle using the manual door lock knobs. Close all the doors.
• Procedure B -- Close all the doors. Use the key or the power door lock switch in order to lock the door. The doors must be closed prior to locking the doors for this procedure.
Disarming the System
In the arm initiated mode, the following conditions are true:
• The security telltale is ON.
• The doors are open.
In order to disarm a system in the arm initiated mode, perform one of the following procedures:
• Press the power door lock switch to the UNLOCK position.
• Press the door unlock button on the key fob.
In order to disarm a system in the arm delay or the armed mode, perform one of the following procedures:
• Use the key in order to unlock one of the doors.
• Press the door unlock button on the key fob.
Deactivating the Alarm
In the alarm mode, the following conditions are true:
• The horns sound intermittently.
• The headlights and the park lamps are flashing.
In order to deactivate a system in the alarm mode, perform one of the following procedures:
• Use the key in order to unlock one of the doors.
• Press the door unlock button on the key fob.
• If the vehicle control module (VCM)/powertrain control module (PCM) receives a valid Passlock™ ignition key rotation.

Hi Edwin, I'm glad to help! Edwin it sounds like the vehicle may have gone into theft alarm mode. If the car doesn't start, Then that is your problem. You might try turning the key in the trunk lock to see if it goes off, if it doesn't try the key in another lock cylinder. Hope this helps and have an awesome day Edwin.

Wait for the new key, honda is the only one that can deal with it unless you can find a lock smith that deals with those.

1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possession,you are done. To end mode open door or insert key into ignition.

You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works

IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Once you program the remotes , all previous codes will be erased from the memory. The other remotes will not be functional until you program the remotes again.
1. Close the vehicle doors.
2. Insert key in ignition and turn to ON (As far as you can without cranking engine)
3. Turn ignition OFF and remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key.
| (Do not turn the ignition key in the lock cylinder.)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder.)

7. Insert the ignition key into the ignition lock cylinder. (Do not turn the
ignition key in the lock cylinder.) Leave the ignition key in the ignition lock
cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to
verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry
transmitter and hold until the vehicle beeps twice to verify that the
transmitter has been successfully programmed (this take approximately 15
seconds).
10. Perform the previous step to program up to four transmitters (including your
old ones).
11. Remove the ignition key in order to exit the Program Mode.

IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Once you program the remotes , all previous codes will be erased from the memory. The other remotes will not be functional until you program the remotes again.
1. Close the vehicle doors.
2. Insert key in ignition and turn to ON (As far as you can without cranking engine)
3. Turn ignition OFF and remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key.
| (Do not turn the ignition key in the lock cylinder.)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder.)

7. Insert the ignition key into the ignition lock cylinder. (Do not turn the
ignition key in the lock cylinder.) Leave the ignition key in the ignition lock
cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to
verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry
transmitter and hold until the vehicle beeps twice to verify that the
transmitter has been successfully programmed (this take approximately 15
seconds).
10. Perform the previous step to program up to four transmitters (including your
old ones).
11. Remove the ignition key in order to exit the Program Mode.

Seating in the drivers seat , make sure all doors are closed.Insert key into ignition, don't turn on yet.
Wait for the dome light to go out, then press and hold the door unlock button , make sure it is UNLOCK, while turning the key ON OFF ON OFF Twice , do not engage the started, just on to the point of being on. Release the unlock button,and your doors should lock, then unlock indicating programming mode.At this point hold down both the lock and unlock button on the key fob. After 30 seconds your locks should lock and unlock, indicating the fob is programmed. This must be repeated for all remotes, whether or not it be new or old. After all remotes are programmed, turn the key off and on again to exit programming mode.

Some cars will lock the steering wheel when the ignition is turned to the lock position. To try and start the car, grab the steering wheel and try to move the steering wheel back and forth while turning the ignition key at the same time. Be aware that the steering wheel could require a pretty good yank before the ignition unlocks.

Hope that helps

make sure the car is in park or the key wil not come out or start also try to turn the key at the same time turn the wheel to the left

Here are the program instructions

1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).
10. Perform the previous step to program up to four transmitters (including your old ones).
11. Remove the ignition key in order to exit the Program Mode