Question about 2005 Chrysler Town & Country

1 Answer

Power sliding doors

I have a problem with left slider door. when I push the button to open it pops open but doesn't open fully but it will close just fine. does anyone know if it needs lube or am i looking at a motor ?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 68 Answers

You are looking at a automatic door motor. The pulling mechanism is going out but the pulling is just fine for a little bit longer

Posted on Nov 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Electronics


Reseting the power sliding door gm Montana or venture? In: Chevy Venture, Pontiac Montana [Edit categories]
[iframe style="BORDER-BOTTOM: 0px; BORDER-LEFT: 0px; VERTICAL-ALIGN: bottom; BORDER-TOP: 0px; BORDER-RIGHT: 0px" id=google_ads_iframe_/51859126/answ_desktop_question_answered_600x300_alt_0 height=300 marginHeight=0 src="javascript:"[/iframe]
Answer:

It's in the owners manual under power door. I believe you pull the fuse under the hood for 15 sec with the overide switch in the off position. ...(roesterman adds...).My power door was opening all the way then closing immediately. I used this method to reset door and it worked! This started happening after I had some body work done to vehicle..maybe they disconnected battery or something. Delay locking was locking doors before slider was closing too. This left the door unlocked. I haven't tested to see if this has been corrected by reset yet.

Apr 06, 2014 | 2002 Pontiac Montana

1 Answer

Sliding door repair


grease the tracks and mechanisms make sure the hardware and springs arent broken..these doors should pop open partway fairly easily..may need new hardware from a salvage yard..

Jan 18, 2014 | 2001 Toyota Sienna

1 Answer

How do i reprogram the power sliding door on a 2005 buick terraza


From the owner's manual:

If your vehicle has

the dual power sliding doors, both doors will have

to be reset. To reset a door, do the following:

1. Check to be sure the power sliding door is

unlocked and securely closed.

2. Turn the ignition to LOCK.

3. If the power sliding door overhead console

switch is in the override (deactivation)

position, return to the activation position.

4. Open the sliding door using the remote

keyless entry transmitter, overhead console

switch, or passenger switch. Allow the door to

travel fully open.

If the door does not travel to the fully open

position, press the overhead console switch to the

override (deactivation) position and slide the

door fully open and closed. Check for foreign

objects in the tracks. Repeat the procedure starting

with Step 1. If the door resists travel to the fully
open position, see your retailer for service.

Dec 27, 2012 | 2006 Buick Terraza

1 Answer

How to remove sliding door inside panel of Mazda MPV


1. Work with slider in open position. It helps if you are on a slight incline so that door stays in fully-open position and won't slam shut on your fingers.
2. Remove inner handles and door panel:
a) Inner handle. Remove the inner handle first. You can't see it too easily but a wire clip about the same thickness as a large paper clip holds the handle to its shaft. It's shaped like an upside down "U" so it needs to be pushed straight up. Press the panel outward around the handle and you can just see the clip. Use a small thin screwdriver to locate the bottom tips of the clip and push it up. You may have to alternate from side to side but it will pop off. Grab it with a pair of needlenose pliers if you have to. The door handle willl now slide off - just pull it towards you.
b) Power window switch. Remove power window button by squeezing hidden tabs along the sides of the button. Again, you may have to push the panel outward a little and pry the switch to see the tabs. Wiggle it a little and the button will release. Pull it out and unplug the wiring harness.
c) Door panel. There are several plastic buttons which hold the panel on at the bottom and up the sides. Use a plastic putty knife to get behind panel and pop it out of the holes.
3. Once all trim fasteners are released, grab the door panel at the bottom and pull straight up to release it at the top. You may have to give it a quick upward tug to get it to release. Push the power window button wires through the mounting hole. Look at the panel buttons to make sure that all of them came off with the panel. If not, remove the remaining ones from the door and put them in their respective slots on the door panel. (Trying to re-attach the panel without the buttons installed on the panel will be frustrating.)
4. Outer handle removal.
a) Unclip the handle lock button / bar by turning the small tab and pulling the bar out of its slot. Hard to describe here but you'll figure it out once you see it.
b) Remove three bolts which hold the handle on the door. Note that one bolt is accessible from the outside of the door along the front jamb.
Replace handle and reverse the steps above.

Notes: Check the locking mechanism and make sure the door opens and closes before you reassemble the panel. Remember to orient the inner handle the right way before you re-attach its spring clip. (I've attached it upside down and it won't work!!!) . Also, be sure to feed the power window wiring harness back through the mounting hole before putting the panel back on.

Nov 06, 2012 | 2000 Mazda MPV

1 Answer

My power sliding door doesn't open fully. It makes clicking sound and a somewhat of a jerking motion. It open or closes slighty but the entire it makes the above mentioned noises. Any help would be...


I'm not sure about the noise, but the jerking motion might be because your the center roller (located in the rear middle of the sliding door) has worn out and need to be replace. This is a will known problem.

Your problem is very hard to answer because 05-10 odyssey has so many problem with sliding door.

rear latch:
-door not to latch close
-door not to work

front latch:
-door not to open

lock actuator:
-door not to open
-door will pop when opening

window motor:
-window not to work
-door will only open half way

center roller:
-jerking motion when opening
-door kick back close while opening
-door kick back open while closing

Door motor:
-door not to work
-cause door to jam

good luck

Dec 17, 2010 | 2005 Honda Odyssey

2 Answers

Power Door Light Stays on after battery was changed by a service department


follow this to reinitialize
1. Push the “MAIN” power switch to the “OFF” position.
The “MAIN” power switch is located on the instrument panel, left of the
steering column.
2. Confirm doors are closed, lights are OFF, and the key is out of the ignition.
3. Disconnect the negative (–) battery terminal and wait 60 seconds.
4. Reconnect the negative (–) battery terminal.
5. Push the “MAIN” power switch to the “ON” position and wait 3 seconds.
6. Push the “DOOR R” switch to open the right door and wait 3 seconds after the door
is completely opened.
7. Push the “DOOR R” switch to close the right door and wait 3 seconds after the door
is completely closed.
8. Push the “DOOR R” switch to open the right door and wait 3 seconds after the door
is completely opened.
9. Push the “DOOR R” switch to close the right door and wait 3 seconds after the door
is completely closed.
10. Push the “DOOR L” switch to open the left door and wait 3 seconds after the door is
completely opened.
11. Push the “DOOR L” switch to close the left door and wait 3 seconds after the door is
completely closed.
12. Push the “DOOR L” switch to open the left door and wait 3 seconds after the door is
completely opened.
13. Push the “DOOR L” switch to close the left door and wait for the door to
completely close.
With ignition in the “ON” position and both power sliding doors in the fully closed
position, the “PWR DOOR” indicator on the dash should NOT illuminate.
14. Confirm proper operation of both doors using the dash, B-pillar switches, and the
transmitter button

Aug 12, 2009 | 2001 Toyota Sienna

2 Answers

Power sliding door opens part way


Replace the wire track harness in the lower door opening.

May 29, 2009 | 2005 Dodge Caravan

3 Answers

1995 pontiac trans sport


Have you tried (with engine off) taking the left bottom fuse out(I believe it's "TAIL" keep it out for a miniute, then put it back in and crank the engine. push the side door button and open it. Wait a few seconds then push button to close. Make sure your battery is fully charged.
The fuse box is in the glove compartment in dash on left hand side.

Dec 11, 2008 | 1995 Pontiac Trans Sport

Not finding what you are looking for?
2005 Chrysler Town & Country Logo

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...