Question about 1999 Chrysler Town & Country

1 Answer

Driver Side Automatic Window

My driver side window is off line. How do I remove door panel to get it back on track

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 422 Answers

You will find a couple of screws on the door panel but other than that the panel is held in place by plastic tabs. just start pulling. if a couple of them break you can go to the autoparts and get new ones.

Posted on Aug 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I put the driver side power window back on track and the door panel for my 2003 Nissan Altima 3.5SE?


R/R the inner door panel, slide the window back on track, reconnect the window transmission to the window, (or reinstall the trans) bolt everything back together (window motor, window trans to door etc.) Make sure the window is in the UP position. use the switch to raise the window & keep it up if all is back together before finally installing the door panel ( make sure the switch & other plugs are plugged in before the door panel is reinstalled.) Lights etc. Good luck

Sep 14, 2014 | 2003 Nissan Altima

1 Answer

Window wont raise


If its automatic, and all other windows raise with the button panel on the drivers door, then your problem is the motor within the door that raises or lowers the window. Easy quick fix.

If manual, the window probably got stuck and is jammed up within the door and needs to be bumped or put back on the track.

Jun 07, 2012 | 2006 Dodge Stratus

1 Answer

How do I remove driver side door window


You need to remove inner door panel by unscrewing the screws on inner door handle and take a flat screw driver wedge it between the panel and door use flash light to see the clips along the sides and lower part of door and pry them free. then look through the inner door cut outs to find window track. Once you see it use ratchet or screw driver and loosen the window free form track. Then carefully remove window.

Apr 01, 2010 | 2003 Mazda MPV

1 Answer

My driver side window will not close all the way


must take door panel off somethin is jamming or broken wore out in either the scissor track mechanism that pushes the window up and down or the belt that works the mechanism

Nov 20, 2009 | 2004 Chevrolet Monte Carlo

1 Answer

My driver side window has come off its track on a 2004 chrysler concorde how do I get the window back on track


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Pull back the weather seal and you'll be able to get to the tracks. You may need to get some replacement clips to remount the window to the track

Oct 08, 2009 | 1998 Chrysler Concorde

1 Answer

Driver side window will not roll up it is off track looking for some help on how to get it back on track?


remove door panel, slacken off all the bolts holding the framework for the window ( do not remove them )....align window back onto track, and re-tighten bolts............making the bolts slack allows you to manipulate the window and track...

Jul 28, 2009 | Chrysler TC Cars & Trucks

1 Answer

Need to remove and replace the driver side door panel


Could be a bad switch, bad window motor, or clutch in window motor, ccould also be that the window itself jumped track.

Jun 04, 2009 | 2000 Buick LeSabre

1 Answer

DRIVER SIDE WINDOW OFF TRACK


you must pull door panel off (you can find the tool at any parts deals) then lift the window up with hands only it is hard but can be done get some one to hold the window glass up and check to see if any parts have fall if so put back on or replace. if not missing clean track and crank up to glass and line up. wind up and down to make sure it stay and then re-place door panel. hope this works it did for me on my 95 contour

alienphone

May 04, 2009 | 1995 Ford Contour

1 Answer

Window off track driver side 1997 sebring


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Mar 23, 2009 | 1997 Chrysler Sebring

Not finding what you are looking for?
1999 Chrysler Town & Country Logo

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...