Question about 1995 Ford Taurus

3 Answers

1995 Ford Taurus brake pad replacement

How do I push the piston into the caliper to make room for new pads on the rear brakes for a 1995 Ford Taurus?

Posted by on

  • 3 more comments 
  • fixstuff2 Jul 07, 2008

    Great advise..Thanks for the help.

    Fixstuff2

  • Anonymous Mar 16, 2014

    how to replace a wheel bearing for 1995 ford taurus

  • Anonymous Mar 26, 2014

    got everyhing else off except the brake lines and cant push it through to hole in the caliper

  • Anonymous Mar 30, 2014

    How do i get brake piston in release position

  • Anonymous Mar 31, 2014

    car off ground will go in reverse or drive (w/o brake pedal pushed) but when brake pedal pushed the car stalls.

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,039 Answers

The piston need to be turn clock wise and push at the same time make sure when you turn it the rubber around the piston dont get damaged it stick to the piston and get torn before you turn just make sure it not sticking to the piston at the auto part store they sell the toll to turn the piston its cheap$$ hope it FIXYA our post thanks pierre

Posted on Jul 06, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

WHAT IS THE BREAK BLEEDING SEQUANCE FOR A 1995 FORD TAURUS GL

Posted on Oct 11, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Ford Master
  • 1,224 Answers

Pierre is right but he forgot to mention that when you do that remove bleed screw to relieve preasure when decompressing the piston in the hardware for the new pads

Posted on Jul 07, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I removed the rotor and brake pads. but when going to change the pads I can not get the piston to go back far enough to put the new ones in. How do you get the piston to push back in order to put the brake...


You will have to use a c-clamp or brake piston compressing tool to get that piston back in, while you have the brake master cylinder fluid reservoir cap off.

Sep 14, 2011 | 1999 Ford Taurus

1 Answer

How do i replace rear brake pads off a 1995 ford contour


Check this REMOVAL & INSTALLATION
(see Figures 1, 2 and 3 / click over images for zoom )

CAUTION Older brake pads or shoes may contain asbestos, which has been determined to be cancer causing agent. Never clean the brake surfaces with compressed air! Avoid inhaling any dust from any brake surface! When cleaning brake surfaces, use a commercially available brake cleaning fluid.
  1. Remove 1 / 2 of the brake fluid from the master cylinder reservoir.
  2. Raise and safely support the vehicle.
  3. Remove the wheels.
  4. Remove the cotter pin and guide pin.
zjlimited_1153.jpg

Fig. 1: Rear disc brake components

  1. Remove the caliper locating pin cover and remove the locating pin.
  2. Swing the rear disc brake caliper away from the brake rotor and anchor plate. There is no need to remove the parking brake cable or brake hose.
  3. Remove the inner and outer disc brake pads.
To install:
  1. If installing new disc brake pads, use rear caliper piston adjuster T87P-2588-A or similar tool, to rotate the rear disc brake piston clockwise, retracting the caliper piston. This will allow room for the new brake pads.
zjlimited_1154.jpg

Fig. 2: Removing the parking brake cable

zjlimited_1155.jpg

Fig. 3: Use the adjuster tool to rotate the piston into the caliper

  1. Install the inner and outer disc brake pads.
  2. Swing the rear disc brake caliper back into position over the disc brake pads.
  3. Clean the locating pin threads and apply 1 drop of a thread locking agent or similar sealer.
  4. Apply a small amount of disc brake caliper slide grease to the shaft of the locating pin.
  5. Reinstall the locating pin and torque to 30 ft. lbs. (41 Nm).
  6. Reinstall the guide pin and the cotter pin.
  7. Adjust the parking brake by operating the parking brake control several times.
  8. Reinstall the wheel and tire assembly. Torque the lug nuts to 62 ft. lbs. (85 Nm).
  9. Lower the vehicle.
  10. Adjust the parking brake by operating the parking brake control several times.
  11. Pump the brake pedal several times to achieve a good pedal before attempting to move the vehicle.
  12. Check the brake fluid level in the master cylinder fluid reservoir and add fluid as necessary.
  13. Road test the vehicle and check for proper brake system operation.

Hope this helps (remember to rate and comment this answer).

May 01, 2011 | 1995 Ford Contour

1 Answer

How do i get the calippers of to get old pads out and new ones in


front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Apr 13, 2011 | Volkswagen Polo Cars & Trucks

1 Answer

I have a 2001 BMW 318I, E46 MODEL , HOW DO YOU FIT BRAKE PADS TO FRONT AND REAR, THANKS TREVOR.


YOU NEED A PISTON COMPRESS TOOL TO PRESS PISTON BACK IN THE BORE WITH THE BLEEDER SCREW OPEN ON THE CALIPER*.CLOSE BLEEDER SCREW JUST BEFORE THE CALIPER PISTON IS PUSHED FULLY INTO CALIPER.THIS WILL ALLOW ROOM FOR NEW BRAKE PADS AND CALIPER FIT OVER THE BRAKE ROTOR.WHEN FINISH.PUTTING BRAKE PADS ON YOU HAVE TO BLEED BRAKE SYSTEM.DONT DRIVE VECHICLE IF YOU CANT GET A GOOD FIRM BRAKES.

Oct 15, 2010 | BMW 318 Cars & Trucks

2 Answers

Change brake pads


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. (On my car y have 288 mm). After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Sep 30, 2010 | Audi A6 Cars & Trucks

2 Answers

How do I push the piston into the caliper to make room for new pads on the rear brakes for a 1995 Ford Taurus?


Place one of the old pads against the piston and then us a 6" c-clamp. Put one end of the clamp against the old pad and one on the backside of the caliper. Crank the clamp until the piston is completely returned into the caliper. I hope this helps.

Mar 27, 2010 | 1995 Ford Taurus

1 Answer

I took the rear wheels off to replace the brake pads on my 1995 Ford Mustang GT convertible and I cannot figure out how to get the pads on and it put back together. Help!


The brake caliper pistons have to be turned back in the caliper in order to install the new pads. I would recommend going to the parts store and maybe renting the tool to do it.

Oct 06, 2009 | 1995 Ford Mustang

1 Answer

Changing the rear brake pads on 91 mu


Chalk the front wheels, car is on jackstands i hope, release the handbrake, use the old pad with a c- clamp to compress the pistion on the caliper, install new pads. may have to take the cap off the master cylinder, if none of this works, open the bleeder valve, and compress the piston, rebleed the caliper.

Feb 24, 2009 | 1995 Isuzu Rodeo

1 Answer

Rear Brakes not loosening up on Mustang


Did you turn the pistons in to allow room for new pads. The calipers are also for your parking brake and need to be turns in when replacing pads.

Jan 29, 2009 | 1997 Ford Mustang Cobra

1 Answer

Rear Disc Brake Piston


Unfortunately, the lip seal which your caliper piston rides on is leaking. The only remedy for this problem is to replace the caliper.

Oct 21, 2008 | 1998 Ford Taurus

Not finding what you are looking for?
1995 Ford Taurus Logo

815 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...