Question about 1986 Dodge Omni

Open Question

86 omni how do you know if its a switch burn. because the front wipers work would it be a different switch then those ones?

Posted by on

1 Suggested Answer

  • 375 Answers

SOURCE: 86 Omni

hey
ply with שךך switch in front,if u already do that so its can be a bad switch burn related fuse.

Posted on Jul 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHERE IS THE WIPER/WASHER FUSE LOCATED ON 2007 PONTIAC TORRENT


In the under hood fuse box , should have diagram inside the lid . Front wiper's or rear ? Front fuse # 36 - 25 amp. Plus Two relay's PCB hi and Wiper PCB relay . Wouldn't think this being fuse problem . Wiper switch , motor etc... The wiper's are control by a computer . BCM - body control module .

The windshield wiper/washer system consists of front and rear wipers. The front and rear wipers are operative when the vehicle is in accessory or run. The front wipers have 4 different modes: Mist, Intermittent, Low, and High. When the front wipers are in the intermittent mode, there are 5 delay modes to chose from, commanded by the windshield wiper washer switch through the body control module (BCM). The rear wipers has an only one mode.

If the fuse is bad , could have a short to ground or wiper motor pulling to much current (amps) . Fuse's don't just blow for no reason ! Could also have DTC'S - diagnostic trouble codes stored in the BCM .
DTC B3715
DTC B3873
DTC B3875
DTC B3922

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
The BCM controls the windshield wiper motor through two output controls, controlling two different PCB relays which control the desired wiper speed, high or low.
DTC B3922 00: Front Wiper Function Select Circuit

The PCB relay's are non- servicable , replace fuse box . Soldered in Your best bet mit be to take it to a qualified repair shop .

Feb 20, 2017 | Pontiac Cars & Trucks

1 Answer

Where is the switch for back wiper on 86 accord hatchback?


It is on the multifunction switch, there are two different switches, one is w/rear wiper and one is wo/rear wiper. If you can't see the switch or it looks different from the one in the picture maybe the car had the switch replaced with the wrong one. . See the switches at the link below.



1986 HONDA ACCORD 2 0L L4 Wiper Washer Switch RockAuto

Jan 23, 2017 | 1986 Honda Accord

1 Answer

Ok I don't have no front washers or my rear wiper wont work I replaced the switch and I replaced the rear wiper motor still don't work and my front wipers work but wont pump


The front and rear wiper systems are on two totally different circuits. You have more than one problem. Need year make and model to offer assistance

Aug 01, 2015 | Cars & Trucks

1 Answer

I Have a 97 Ford Explorer XLT 4 door with power windows, the windows and wipers stop and start working at the same time, has anyone seenthis before?


what does that mean.
1: active window and wipers move , or reverse.
2: or i must turn on both to get either working??????
or????? be more clear. please.
all wipers move front and rear.?
and all windows do this or just one?


Shot gun effects:
and forgot to do the tests. and that meant you missed bad connections.
money to burn?
the FSM book covers this 100% read that. see those tests.
guessing works like 20% time? shot gun, 50%. leaving what?
wires and connections and bad fuses,(hair cracked)

ill look up what wire that is using alldata.com
so can you , hint?
pardon my shock but never knew folks did shot gun fixes.. wow....
pay a tech 1hr labor for him to tell you what it is ?
I know , you live in the jungle forest like me.
here we go, there. alldata.

fuse 16 runs the
here is the left front, window.
the GEM controls both wipers and windows. so , my guess
bad GEM or the inputs to it are WRONG. (basic logic 101)
be more clear on what works, here, and dont. all windows and all wipers front and rear and what this means.
at the same time

56363e00-bc37-432f-b269-26892a74ea77.jpg

Jun 24, 2014 | 2002 Dodge Stratus

2 Answers

Front wipers working ok, why reae wipers not working?


there is a separate wiper motor for the rear and the front. the rear one has died. these tend to corrode up and freeze faster than the front as they are used much less. if you know anyone so inclined you may be able to take it apart, lubricate the poop out of it, reassemble and find that it works again. if not you will have to buy a new one or just live with it.

Apr 01, 2011 | Renault Le Car Cars & Trucks

1 Answer

1997 Land Rover Discovery II windshield wiper stop working


It sounds lilke the wipers are just going through the "park routine": one swipe and stop.

The melted part is the end of a wiring harness. But replacing this will not solve the problem. It sounds like you have a bad wiper motor which is pulling too much current and overheating.

There are switches on the wiper motor which probably have burned out and the only one left working is the park switch.

May 04, 2009 | 2002 Land Rover Discovery Series II

2 Answers

Rear wiper does not work at all. front wipers work fine. rear washer works


1. check the fuse to the rear wiper motor
2. check for power to rear wiper motor at the motor (power wire going in to the wiper motor with rear wiper switch on)
If you have good fuses & have power going in to the rear wiper motor...
3. Pull old rear wiper motor and install a new rear wiper motor.
Thank you please drive thru......

Feb 26, 2009 | 2001 Ford Expedition

1 Answer

86 Omni


hey
ply with שךך switch in front,if u already do that so its can be a bad switch burn related fuse.

Jul 06, 2008 | 1986 Dodge Omni

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

71043 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6981 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...