Question about 2002 Toyota Camry

1 Answer

How do i remove serpentine belt to change water pump?

How do i remove serpintine belt to change water pump on a 2002 camry?

Posted by on

  • DIAZMAIL Sep 17, 2008




1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Toyota Master
  • 77,544 Answers

There is a pulley thast moves around a little when the engine is running, this is the belt tensioner pulley, you will need either a special wrench or a ratchet to release the tension on the belt.

Posted on Sep 09, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Don't you have to remove the serpintine belt first on a 2002 Buick Rendezvous?

You would not have to remove the belt to work on the brakes.
But yes the belt would be removed to replace the pump.

Aug 23, 2015 | 2002 Buick Rendezvous

1 Answer

Installing serpintine belt on 2002 tauras

Pretty simple...........but remove the coolant expansion tank to make it easier.Pay attention to the condition of the tensioner and its bearing,along with the amount of play in the other idler pulley and WATER PUMP.If you haven't done this before,have a good mechanic help you. don-ohio

Oct 02, 2011 | 2002 Ford Taurus

1 Answer


the crankshaft sensor is located right behind the harmonic balancer mounted on the timing cover-.on the 3.8 , The camshaft position sensor is located behind the water pump pulley on the left side of the engine block. it has a 3 wire connector. you have to remove serpintine belt and water pump pulley to access it.I believe there is ( 4-8mm bolts) to remove. ON THE 3.1 IT IS UNDER POWER STEERING PUMP ON BELT SIDE. REMOVE THE BELT THEN REMOVE AND SET STEERING PUMP TO THE SIDE, BUT DO NOT REMOVE ANY POWER STEERING HOSES FROM IT. have a good day ! if its a differant engine, just repost.

Apr 29, 2011 | 1998 Buick Century

1 Answer

Serpintine belt diagram

what engine? Please rate if it helps

3.L v6

snorkelbobby_26.gif Item Part Number Description 1 3A733 Power steering pump pulley 2 8620 Drive belt 3 2E884 A/C clutch pulley 4 6316 Crankshaft pulley 5 6B209 Drive belt tensioner 6 10344 Generator pulley

2.0L Zetec 4 cyl with A/C

snorkelbobby_27.gif Item Part Number Description 1 10344 Generator pulley 2 19A216 Belt idler pulley 3 3A733 Power steering pump pulley 4 6C301 Drive belt 5 2E884 A/C clutch pulley 6 6B320 Crankshaft pulley 7 8509 Water pump pulley 8 6A228 Drive belt tensioner

Jan 12, 2011 | 2002 Ford Escape

1 Answer

I need an exploded view of water pump replacement

Not too difficult of fix. You'll need to remove the serpintine belt. Drain the radiator. Remove the pulley from the water pump ( I believe three 10MM bolts) After removing this pulley you'll have access to all of the bolts holding in the water pump (I believe there are 5 or 6 8MM bolts) Reverse on install. No need to over tighten on the replacement pump as it has an o-ring seal. Take special care in reinstalling the serpintine belt. I'd get a bit of help to help hold the belt in place as you go.

I hope this may have assisted you, please let me know.


Apr 18, 2010 | 1996 Plymouth Voyager

1 Answer

Trying to get instructions on replacing a side mounted water pump

Place front end on jacks or ramps. I belive there is a lower plastic guard that protects the serpintine belt from water splash ( I know the 96's did not have it but uncertain about 1997, is so remove it) Drain radiator/cooling system. The serpintine belt will have to be removed, you'll need to use a box end wrend on the tensioner to remove pressure from belt, it will fight you but she will go. Next remove bolts that hold pulley on to water pump shaft (I believe there are three, all 10MM) next remove all of the bolts that hold the water pump on, I belive there are either 5 or 6, either 8 or 10MM. Clean surface where pump applies to, be certain to use new o-ring, should be with water pump. Reassemble in reverse, install new serpentine belt and use proper 50/50 mix of radiator fluid and water. Start engine, let it come to heat and check for leaks, keep eye on temp gage to be certain things are ok.

I hope this may have assisted you,

Apr 15, 2010 | 1997 Plymouth Voyager

1 Answer

Need a diagram

This is a drive belt routing for a Toyota Camry 2002 with a 2.4L four-cylinder engine. I hope this will help you out.

Oct 04, 2009 | 2002 Toyota Camry

1 Answer

Need serpintinebelt diagram for 2002 camry 4cyl

for the most part there is a diagram under the hood showing you how the belt goes on try this website to see if they have you car listed its and you can also check at the auto parts store where you are going to get the new belts to see if they have a diagram for your car

Apr 26, 2009 | 2002 Toyota Camry

Not finding what you are looking for?
2002 Toyota Camry Logo

239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides