Question about 2002 Suzuki Grand Vitara

1 Answer

Reprogram remote how do I reprogram the unlock lock remote?

Posted by on

1 Answer

Xl-7 programming instructions first you need to stuff your head up under the dash and locate your module drivers side upper corner under dash does it say programmable transmitter (the first models had no programable modules) if it says that then......
1 confirm all doors are shut and key is out of ignition
2 open drivers door insert key and turn to on within 10 sec
3 turn ignition switch to off in 10 sec
4 push and release drivers door switch 3 times in 20 sec
5 turn ign. switch to on in 10 sec
6 turn ign. switch to off in 10 sec
7 press and hold lock and unlock button on transmitter for 5 sec within 20 sec of step 6 alldoors will lock/unlockto confirm correct process
8 press lock unlock buttons on second remote within 5 sec after step 7 once again all doors will lock/unlock to confirm
9 to add another remote up to a max of four repeat steps 1 through 8 this was taken directly out of an owners manual supplement that comes with a new keyless entry kit (part number for a xl-7 or grand vitara can't remember which one it goes to but it works on either one is 84900-67810) which you would have to purchase if yours is not programable these instructions are the same for vitara, grand vitara, xl-7 and the esteem hope this helps

Posted on Jul 11, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Keyless receiver


immobilizer control module under the dash.some vechicles if you replace key remote dealership has to reprogram remotes using diagnostic equipment.try this techinique to synchronize remote transmitter. stand within 5 feet from vechicle .press transmitter lock and unlock buttons simultaneously for 7 seconds . system will lock and unlock doors confirming synchronization. if this dont help dealership has to reprogram remotes.

Dec 13, 2013 | 1997 Chevrolet Blazer

1 Answer

Replaced batery in key fob and now there is no connection between fob and security system...I can lock and unlock doors with the key and I can start car ...fob doesn't work; does not lock or unlock...


reprogram the remote transmitter. first leave driver door open all other doors closed,key removed from the ignition switch. insert key into the ignition switch,then remove it.press lock and unlock on the vechicle door lock control switch at 1 second intervals 5 times. close and repoen drivers door.press lock and unlock on the vechicle lock control switch at 1 second intervals 5 times. insert key into ignition switch. switch ignition on and off twice to program a remote transmitter code whilst erasing the original codes or three timre to check how many remote transmitters are currently registered.remove key from the ignition switch.system should now lock and unlock.twice to indicate programming mode or one to four times,slowly to indicate number of remote transmitters registered.for the solara press and hold lock and unlock remote buttons together, press lock remote button for a second period of 1 second. system should now lock and unlock vechicle.once to confirm, twice to indicate registration has failed.if required repeat button procedure to program remaining remote transmitters.note to exit programming mode close drivers door or insert ignition key.maximum of 4 remote transmitters can be programmed.if akk failed let dealership reprogram remote transmitters.

May 18, 2011 | 1999 Toyota Camry Solara

2 Answers

Where do I find the keyless entry code for my 1999 Mercury Mountaineer? Then when I use the remote to unlock or lock the Mountaineer, the locks will pop up or the horn will blow or all four locks will...


TRY THIS REPROGRAMMING PROCEDURE. SWITCH THE IGNITION OFF TO ON 8 TIMES WITHIN 10 SECONDS. DOORS SHOULD LOCK THEN UNLOCK. PRESS ANY BUTTON ON THE FIRST REMOTE TRANSMITTER. DOORS SHOULD LOCK THEN UNLOCK. IF YOU HAVE ANOTHER CAR REMOTE REPROGRAM IT THE SAME WAY. WHEN DONE SWITCH IGNITION SWITCH OFF.

Jan 27, 2011 | 1999 Mercury Mountaineer

1 Answer

Hello, I have a question, how to do yo reprogram the remote control on a 2004 GMC Yukon?


CLOSE ALL DOORS INSERT KEY INTO IGNITION.DO NOT TURN THE IGNITION SWITCH.PRESS AND HOLD DOOR LOCK SWITCH IN THE UNLOCK POSITION.SWITCH THE IGNITION ON OFF ON OFF.RELEASE DOOR LOCK SWITCH.SYSTEM SHOULD NOW LOCK AND UNLOCK VECHICLE INDICATING PROGRAMMING MODE ACTIVATED.PROCEED AS FOLLOWS.NOTE EXISTING REMOTE TRANSMITTER MEMORY POSITIONS WILL BE OVERWRITTEN.PRESS AND HOLD LOCK AND UNLOCK BUTTONS ON THE FIRST REMOTE TRANSMITTER FOR 15 SECONDS.SYSTEM WILL LOCK AND UNLOCK VECHICLE INDICATING REMOTE TRANSMITTER PROGRAMMED.REPEAT ABOVE PROCEDURE FOR EACH REMOTE TRANSMITTER.IF THIS DONT HELP DEALERSHIP HAS TO REPROGRAM REMOTE.

Aug 09, 2010 | 2004 GMC Yukon

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

2 Answers

Key remote wont work even with new batteries


The remote likely needs to be reprogramed. If you have both remotes you will need to take these to the dealer and have them reprogramed.

Jan 25, 2010 | 2000 Volkswagen Beetle

2 Answers

Replaced the battery in the remote, but still nothing when I go to lock or unlock my door or set off the alarm, nothing happens.


Your remote needs to be "reprogrammed" after battery replacement. Not sure if yours is done in this manner. This is how my remote is reprogrammed on my 1999 Corvette. Stand beside drivers side door, point remote at the car while holding the Lock and Unlock buttons at the same time. Within 10-15 seconds the horn should beep letting you know the reprogramming was successful.

Dec 23, 2009 | 2003 GMC Yukon XL

1 Answer

Need to reprogram door locks for 2004 Toyota Camry


I recently replaced the battery on my 2004 Toyota Camry. When I installed new battery the door locks will not stay unlocked once opened with remote. How do I reprogram?

Feb 21, 2009 | 2005 Toyota Camry Solara

1 Answer

Reprogramming oem silverado remote


1.) from driver seat , close all doors.
2.) insert key into ignition.
3.) while HOLDING the door lock switch in the unlock position , cycle the ignition switch ON OFF ON OFF.
4.) release the door unlock switch , the doors will lock and unlock to confirm programming mode.
5.) press and HOLD the UNLOCK button and LOCK button simultaneously on one transmitter , after a delay of 15 - 30 seconds , doors will lock and unlock to confirm programming of that transmitter.
6.) repeat step number 5 for up to 4 remotes.
7.) turn ignition switch to the RUN position to exit the programming mode.
8.) test remote operation of each remote.

fixed ya

Dec 24, 2008 | 2003 Chevrolet Silverado 2500HD

Not finding what you are looking for?
2002 Suzuki Grand Vitara Logo

1,021 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...