Question about 1999 BMW 323 Series

1 Answer

Replacing belts on 2000 323 ci.

Do I have to remove the radiator to replace the belts?

Posted by on

  • Anonymous Jul 13, 2008

    how change the pullies and belts

  • giz_jo_kit Aug 15, 2008

    Car recently had an acident, front smashed up to pullies&belts , how do i replace the belts?!!

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

U can remove the belts from tentioners under the front of the car

Posted on Sep 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the radiator on a 2001 Chevrolet Monte Carlo


1. Empty the radiator
2. disconnect top and lower hoses on the radiator.
3. remove plastic cowling, (should be an upper and lower half with two bolts on each side. There may be an upper plastic cowling as well that will have to be removed.
4. sometimes you can work around the fan, if not remove the fan belt and fan. Make a drawing of how the serpentine belt goes on if it has a serpentine belt. There should be a tension wheel on the belt used for removal and installation of the belt. Be very carefull of your fingers when removing and installing the belt.
5. Remove the four or six bolts that hold the radiator on and lift the radiator out. It may be easier with two people to lift the radiator out.
GOOD LUCK, IT'S NOT A VERY HARD JOB AND ONCE YOU'VE DONE IT ONCE IT GOES PRETTY FAST.

Nov 22, 2014 | 2001 Chevrolet Monte Carlo

1 Answer

2001 Nissan Frontier REPLACE WATER PUMP - removed Radiator & Hoses Need HELP with REMAINDER


NOTE: When removing water pump assembly, be careful not to get coolant on timing belt unless you intend to replace it. (if it has more than 60.000 miles. it probably SHOULD be replaced, however, you must do it correctly or severe engine damage will occur.)
Drain coolant from drain plugs on both sides of cylinder block and radiator.
Remove radiator hoses (upper and lower) and fan shroud.
Remove drive belts.
Remove water pump pulley.
Remove crankshaft pulley and front (upper and lower) belt cover.
Remove water pump

Oct 01, 2011 | 2001 Nissan Frontier Crew Cab

1 Answer

How do i replace the water pump on a 1997 rodeo v6?


YOU HAVE TO REMOVE TIMING BELT AND IDLER PULLEY.YOU NEED TO REPLACE TIMING BELT WHEN YOU REPLACE WATER PUMP.TO REPLACE WATER PUMP. DRAIN COOLANT SYSTEM.REMOVE UPPER RADIATOR HOSE.REMOVE TIMING BELT AND IDLER PULLEY.UNBOLT AND REMOVE THE WATER PUMP.CLEAN ANY GASKET MATERIAL OR SEALANT RESIDUE FROM THE WATER PUMP MATING SEALING SURFACES.WHEN INSTALLING NEW WATER PUMP BESURE TO USE A SEALANT ON BOTH SIDES OF WATER PUMP GASKET TO KEEP IT FROM LEAKING COOLANT.TORQUE WATER PUMP BOLTS TO 13 FT LBS IN A TWO STEP CRISSCROSS SEQUENCE.INSTALL THE IDLER PULLEY.TIGHTEN THE MOUNTING BOLT TO 31 FT LBS.INSTALL AND TENSION THE TIMING BELT.INSTALL THE UPPER RADIATOR HOSE.REFILL BLEED THE COOLANT SYSTEM.

Feb 19, 2011 | 1997 Isuzu Rodeo

1 Answer

Where is the crankshaft positioning sensor located on a '92 buick century w/a 3.3 ci & how do you replace it.


Behind the large pulley at the lower part of your motor. You have to remove the belt and then loosen the large bolt that holds it in place. Use a pulley puller to remove the harmonic balancer. With that off, loosen the screw that holds the bracket to the mount. Position the new bracket on the mount and tighten. Be sure that the gaps in the new sensor are postioned correctly. Replace balancer and belt and you should be good to go.

Aug 19, 2010 | 1992 Buick Century

1 Answer

How do i replace a water pump on a 1993 geo


1 disconnect battery ground cable
2 drain cooling system
3 on models with a/c, proceed as follows:

a discharge a/c system
b loosen upper and lower compressor bolts and remove compressor drive belt
c remove a/c line from top of radiator shroud

4 remove water pump drive belt
5 remove reservoir tank from radiator bracket
6 remove radiator shroud and fan/clutch from vehicle
7 remove waterpump pulley from waterpump
8 remove timing tensioner and timing belt
9 remove dipstick tube
10 remove alternator mounting bracket at water pump
11 remove water pump mounting bolts and water pump
12 reverse procedure to install, using new gasket and rubber seal

Feb 18, 2010 | 1993 Geo Tracker

1 Answer

Replacing an anti knock sensor on a 2000 ford


remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intake housinng once you have remove all the above, your freaken engine will look naked, you can see the location of the knock sensor is locate in the engine valley

Jan 29, 2010 | 2000 Ford Focus

1 Answer

How to replace knock sensor in 1995 nissan altima


remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intake housinng once you have remove all the above, your freaken engine will look naked, you can see the location of the knock sensor is locate in the engine valley

Jan 20, 2010 | 1995 Nissan Altima

1 Answer

My girlfriend ran over a large rock and the belts popped and water spilled onto the gorund. Which belts do I need to replace.


If it has more than 1 belt . If your going to replace 1 you should go ahead and replace them all , you have to remove all the parts anyway so do them all while your there. As for the water on the ground , check the radiator for leaks & the bottom radiator hose.If the radiator & the hose are fine it could have been the water pump belt. Hope it didn't run hot.

Jun 23, 2009 | 1998 Mazda 626

1 Answer

How to replace a serpentine belt on a ford taurus 2002


just replaced serpentine belt on my 2000 taurus with the push rod engine, first remove the plastic radiator recovery bottle.
next using a 15mm closed end wrench, remove the tension from the aerpentine belt. paying special attention on the routing of the belt prior to removing. Remove the old belt. Reverse this procedure to replace the belt.

Aug 11, 2008 | 2000 Ford Taurus

Not finding what you are looking for?
1999 BMW 323 Series Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Fred Sops

Level 2 Expert

271 Answers

Al Clark

Level 2 Expert

290 Answers

Doberman

Level 2 Expert

246 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...