Question about 2002 Ford Windstar Cargo

3 Answers

5 digit code for keypad entry

I don't know where to find my 5 digit keypad code on my 2002 windstar

Posted by on

  • mmnj Jul 13, 2008

    I was asking where to find the CODE, not the keypad! I'm not that stupid.

    Thanks

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

I have an '01 Windstar with the same accessory. Try this: Open the liftgate & open the plastic panel on the left side (with lovers in it). The master computer is under that cover, and my van's door code is written on the label on the computer. I'm not sure if they're all that way, but it's worth a look.

Good luck!

Pete

Posted on Aug 14, 2008

  • Carssuck Aug 14, 2008

    I meant to say "LOUVERS", not "LOVERS"! Sorry!

×

You have to take it to a Ford dealer and have them pull it from the computer. All they do is hook up there computer and get the code for you. My local dealer charged me 25.00 to get the code.

Posted on Jul 28, 2008

On the drivers door just above the handle and below the glass

Posted on Jul 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I find the keyless entry code for a 2001 ford windstar


The manual says:
The keypad can be operated with the factory set 5-digit entry code; this code is located on the owner's wallet card in the glove box, is marked on the computer module, and is available from your authorized dealer. You can also create your own 5-digit personal entry code.
(someone on the internet says: A sticker that is located on the computer module - this should be located underneath the dash/steering wheel on the driver's side (by the fuze box - bolted to the firewall of the car/van)

Are you the original owner? This number can be reprogrammed, so it may not be the original number. Does the keypad work ok? Did you test to see that lights come on when each of the 5 buttons are pressed?

Jun 04, 2014 | 2003 Ford Windstar

1 Answer

How to reset my keypad on my 2002 navigater


Follow the instructions in your owners manual, but you must have the original code, if you don't the code is on the keyless entry module. If you do not have an owners manual you can download one HERE.

Jul 15, 2012 | 2002 Lincoln Navigator

1 Answer

How to reset anti theft system


KEYLESS ENTRY SYSTEM You can use the keyless entry keypad to:• lock or unlock the doors without using a key.• open the trunk.• recall memory seat/mirrors/steering column/adjustable pedals positions1 or 2. The keypad can be operated with the factory set 5-digit entry code; this code is located on the owner's wallet card in the glove box, is marked on the computer module, and is available from your authorized dealer. You can also create your own 5-digit personal entry code. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation. Programming a personal entry code. To create your own personal entry code: 1. Enter the factory set code. 2. Within five seconds press the 1 • 2 on the keypad. Note: The lock motors will cycle, locked then unlocked 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other. 4. Enter a sixth digit to indicate which personality feature should be recalled by the personal code. Note: The lock motors will cycle, locked then unlocked. • 1 • 2 recalls driver personality 1. • 3 • 4 recalls driver personality 2. • 9 • 0 does not recall a driver personality. Wait 5 seconds without pressing a keypad button in order to store a personal entry code. Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personal code. • If you set a personal code and store it over an existing personal code it will erase that personal code only. Erasing personal code 1. Enter the factory set 5-digit code. 2. Press and hold the 1 • 2 for two seconds and release; this must be done within five seconds of completing step 1. 3. Press and hold the 1 • 2 for two seconds to erase the customer programmed code; this must be done within five seconds of completing step 2. Your personal code is now erased and only the factory set 5-digit code will work.

Feb 09, 2011 | 2002 Lincoln LS

1 Answer

Where keypad entry code located on 2007 Lincoln


found a 5 digit number under bar code behind glove compartment.could this be the keypad entry code to
2007 mkz.dino

Jun 30, 2010 | 2007 Lincoln MKZ

1 Answer

I don't have a manual for my 2004 lincoln Avaitor but would like to know how I can change the code on the drives door key pad


KEYLESS ENTRY SYSTEM With the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key. Your vehicle has a factory set 5 digit code that operates the keyless entry system. You can also program your own 5 digit personal entry code. The factory-set code is located: • on the owner's wallet card in the glove compartment • or at your dealer. When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation. This system will disable the power door lock controls. These will not work until the vehicle is disarmed. Programming your own personal entry code To program your own code: 5. Enter factory set code (keypad will illuminate when pressed). 6. Press 1/2 control within five seconds of step 1. 7. Enter your personal 5 digit code. Enter each digit within five seconds of previous one. 8. After the code is entered, the locks will cycle, confirming that the new code has been set. Do not set a code that includes five of the same number or presents them in sequential order. Thieves can easily figure out these types of codes. Your personal code does not replace the permanent code that the dealership gave you. You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase the first personal code in favor of the new code. Locks and Security 149 Locks and Security If you wish to erase your personal code, use the following instructions: 1. Enter factory set code. 2. Press 1/2 control and release. The system will now only respond to the factory set code. Anti-scan feature The anti-scan feature prevents repeated attempts at arriving at a valid key code. The keyless entry pad is disabled for 1 minute after 7 unsuccessful attempts (35 consecutive button presses) at entering a valid key code. The keypad will flash during this 1 minute mode. However, the 7/8 and 9/0 controls will still lock the vehicle. Anti-scan will be turned off after: • one minute of keypad inactivity. • the remote entry transmitter UNLOCK button is pressed. • the ignition is turned to the ON position. Unlocking the doors with the keyless entry system To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will also illuminate. To unlock all doors, enter the factory set code or personal code (driver door unlocks) and press the 3/4 control within five seconds. Locking the doors with the keyless entry system It is not necessary to enter the factory or personal code prior to locking all doors. To lock the doors: • with the driver's door closed, press the 7/8 control and the 9/0 control at the same time.

Dec 17, 2009 | 2004 Lincoln Aviator

2 Answers

How do i reprogram keyless entry codes


door pad keyless codes?

in owner manual, enter permanent code and then press "1" and enter personal code, then press "1" again. Then both codes will work.

If you don't have manual, go to Motorcraft.com and click on technical resources and click on your year owner manual.

---------------------------------------------
Each vehicle equipped with a keyless entry keypad is programmed with a five-digit entry code. This code is provided to the customer through a wallet card in the Owner Literature package. In addition, this code is available through a diagnostic tool and is also printed on the vehicle security module label. When entering codes each digit must be entered within five seconds of the previous button press.
Programming/Erasing Personal Code
A unique personal five-digit code can be programmed by following these steps:
  1. Enter the factory set five-digit code (the keypad will illuminate when pressed).
  1. Press 1/2 within five seconds of Step 1.
  1. Enter the unique five-digit code.
The personal code does not substitute for the permanent factory set code. Either code can be used to access the vehicle. In addition, if a second personal code is programmed, it will simply overwrite the previous personal code. To erase a personal code, carry out the following procedure:
  1. Enter factory set five-digit code.
  1. Press 1/2 within five seconds of Step 1.
  1. Press 7/8 and 9/0 at the same time within five seconds of Step 2.
The system will now only respond to the factory set code.
Anti-Scan Feature
To provide added security, the keyless entry pad is disabled for one minute after 35 button presses without a valid entry code being entered. The keypad will flash during this one-minute mode with all functionality disabled except for 7/8 and 9/0 still being allowed to lock the vehicle.
Anti-Scan will be turned off after any of the following events:
  • one minute of keypad inactivity
  • the keyless entry remote transmitter UNLOCK button is pressed
  • the ignition is turned to the ON position.
Unlocking the Doors with the Keyless Entry Keypad System
To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will illuminate.
To unlock all doors, enter either the factory set code or the personal code (driver door unlocks) and press the 3/4 control within five seconds.
Locking the Doors with the Keyless Entry Keypad System
It is not necessary to enter the factory set or personal code prior to locking all doors. To lock all doors, press the 7/8 and 9/0 controls at the same time.
Inspection and Verification
  1. Verify the customer concern by operating the system.
  1. Visually inspect for obvious signs of mechanical or electrical damage.

Dec 01, 2009 | 2004 Ford F350

1 Answer

I just bougt 2003 windstar trying to find keyless entry code can"t find lacation


Keyless entry code is on REMOTE KEYLESS ENTRY MODULE .You have to remove utility compartment at lower center of dash and then you will see module with 5 digit code on white label. Hope this helps.

Jul 09, 2009 | 2003 Ford Windstar

1 Answer

Keypad reset. Now that I have the original keypad code, how do I change the code?


your owner manual tells you. Why not use the original code?

To change, here is 96 procedure, should be the same. please give good rating if this is what you want.

Entry Code The system (permanent) entry code is located in three places:
  • on the owner's wallet code card (in glove compartment)
  • electronically accessible by requesting the remote anti-theft personality module KEYCODE PID on the New Generation Star (NGS) Tester
  • on the remote anti-theft personality module housing
The remote anti-theft personality module is programmed at the factory with a five-digit entry code. A replacement remote anti-theft personality module includes replacement labels and a new owner's code card. To turn on the interior lamps and light all illuminated components:
  • press any button on the keyless entry keypad (14A626).
To program a temporary access code:
  • Enter the permanent code on the keyless entry keypad.
  • Press button 1/2 within 5 seconds of last digit of permanent code. (This alerts system to accept temporary code.)
  • Enter alternate five-digit code. Do not exceed 5 seconds between entering digits or between pressing the 1/2 key and entering the first digit.

Apr 08, 2009 | 1995 Ford Taurus

1 Answer

Keyless entry keypad


retrieving is probably not an option however if you know the factory code , you can add 1 personal code which in turn would erase any other personal codes . your owners manual should back this statement up . follow these steps >>>>>

The keyless entry touch pad can use two codes. The factory code and one
personal code .
To program your own personal code, select a 5 digit code that doesn't use 5 digits in
sequence or the same button 5 times.
Enter your factory code
Within 5 seconds press the 1/2 button
Within 5 seconds of pressing the 1/2 button, enter your 5 digit personal code,
pressing each digit within 5 seconds of the previous digit.
You can now use either code to operate the keypad

Jan 12, 2009 | 2003 Ford Expedition

3 Answers

Keyless entry


I believe dealer has to re-program the new code.

Aug 29, 2008 | 2001 Ford Explorer Sport Trac

Not finding what you are looking for?
Cars & Trucks Logo

350 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...