Question about 2002 Jaguar X-Type

1 Answer

Clutch problem Lost hydrolics

Posted by on

  • patsy51 Jul 05, 2008

    Your solution sounds about right.Thanks will look at that first.Patsy51

  • patsy51 Jul 19, 2008

    CLUTCH COMES AS COMPLETE ASSEMBLE INC.SLAVE CYLINDER,SO IF LIKE MINE FAILS,600pounds PARTS ONLY

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,036 Answers

Hi,
Check any flexible hoses used for condition, check clutch reservoir that it still contains fluid.

If it does, ask an assistant to press the clutch down fully - while you watch the liquid level. It should fall, then rise again when off the pedal. If it just stays put, you need new seals on the master cylinder.

If all the fluid is gone, but no obvious leaks, remove the slave cylinder, and replace the seals in that or replace with new unit.

it is possible that you just have a slight leak in the slave cylnder, allowing the fluid level to fall enough to allow air in the system giving the fault. Again, replace seals in slave cylinder, and refill with clean brake/clutch fluid, and bleed out the air using the bleed nipple on the slave cylinder.

Any reasonable garage will do this for you if access is difficult.

Thank you for using Fixya!

Posted on Jul 05, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch not engaging after being changed


Probably just need to bleed the hydrolic clutch.. You should be able to see the assemble for the hydrolic fork and what looks like a bleeder screw that you would find on your brakes... Bleed it the same way you would brakes..

May 06, 2014 | 1991 Honda Accord

1 Answer

Clutch has no pressure


If it has a hydrolic clutch, the slave cylinder may be bad. There may also be a leak in the system. There should be a seperate master cylinder for the clutch system if it has a hydrolic unit.

Apr 30, 2014 | 2003 Ford Explorer Sport Trac

1 Answer

I was driving it and i pressed the brake and all of a sudden the brake pedal and clutch pedal both went down a piece by the pedal broke an now it wont go in to gear


Hi

the Hydrolic clutch has failed by the sound of it, the clutch on his car shares fluid with the brakes hence why both pedals went down. you might be lucky and the slave cylinder might have failed or lost pressure, this in fact is very common on this car.

Have the slave cylinder checked out and look under the car for any fluid leaks

Regards

Dan

Jan 02, 2011 | Ford Ranger Cars & Trucks

1 Answer

I was driving my ford bronco, i put it in neutral while i was waiting at a light, my clutch seemed to go out but i kept pumping the clutch and it built up pressure and worked again, a few miles down the...


IS IT A CABLE OR HYDROLIC CLUTCH? CABLE - FLEX PLATE IS WEARING OUT, REPLACE CLUTCH PLATE, FLEXPLATE AND THROWOUT BEARING.
HYDROLIC - CAN BE THE MASTER CYLINDER GOING BAD OR THE SLAVE CYLINDER GOING BAD, OR COULD BE THE CLUTCH NEEDS TO BE REPLACED. FOLLOW INSTRUCTIONS ABOVE.

Aug 05, 2010 | 1988 Ford Bronco II

1 Answer

My cluch keeps stiking to the floor in my 1989 mazda mx6


check all mechanical parts of clutch pedal make sure there is no catching or draging in its joint lube if possible also check the spring that pulls the clutch pedal back up make sure not damaged or worn out, A different problem may be in your hydrolic clutch system, such as a bad slave cylinder or your system may just need bleeding, if you have a problem with your hydrolics when the clutch goes to the floor and stays you will not be able to disengage your clutch as well until you pull the clucth back up and pump it a few times.

Apr 03, 2010 | 1989 Mazda MX-6

1 Answer

Needs to bleed the hydrolic clutch


want to know a short cut? (trick) take the master cylinder for the clutch off the firewall and tilt forward while pumping the pistron by hand and bleeding those fords are notorious for air locking in the master cylinder due to the fact!! they fasten to the firewall at a backwards tilt!! i have done over 2700 of them in 45 years

Jan 13, 2010 | 1991 Ford F250

1 Answer

Hyundai tucson clutch


Thank you for the request. Since the car only has 24,000 miles on it, I would take it back to the dealer. It does sound like that your clutch needs an adjustment of some type. Since I do not own a Hyundai I have no idea what the actual problem might be. I just did some research and found out that the clutch in your car is hydrolic (meaning that it uses a master and slave cylinder with hydrolic fluid to push the clutch arm when you push the clutch pedal with your foot). Trying to work on this type of clutch system can sometimes be a very hard to do. With the small amount of miles your car has on it, I would get the dealer involved in solving this problem. It could be something as simple as bleeding air from the hydrolic system of the clutch or it might be replacement of either the master cylinder, the slave cylinder and/or the fluid line that goes in between those two cylinders.

Much good luck in fixing this problem.


Nov 26, 2008 | 2005 Hyundai Tucson

Not finding what you are looking for?
2002 Jaguar X-Type Logo

479 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

63801 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...