Question about 1987 Porsche 944

1 Answer

Heater problem temperature control switch not working

Posted by on

  • 4578at Jul 05, 2008

    temperature control switch not working

  • Anonymous Oct 29, 2008

    I have a1987 olds 442 old heater switch had 4 speeds only two middle worked low and high didnt ,I put a new switch in same thing happens any ideas ?

×

1 Answer

Call martin

Posted on Aug 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No heat. New thermastat, heater core flushed, good circulation. Has a rear heater.


Does blower motor work , air blowing out of ducts ?
Temperature blending is varied by the air temperature control door, which regulates the amount of air that flows through and/or around the heater core (18476) , where it is then mixed and distributed.
Movement of the control knob from COOL (Blue) to WARM (Red) causes a corresponding movement on the air temperature control door and determines the temperature that the system will maintain.
Temperature Control
The temperature control operates in the following manner:
  • Temperature control of the heater system is determined by the position of the temperature control knob (between COOL-BLUE and WARM-RED) of the heater control .
  • This control knob is connected to a potentiometer mounted in the heater control . This potentiometer is electrically connected to the electric blend door actuator that operates the A/C air temperature control door.

Feb 25, 2016 | 1996 Ford Windstar

1 Answer

I replaced the heat blend actuator because I was not getting any heat. Now, after replacing, all I get is hot air and no cold. The A/C was working fine just before replacing.


Do you have Manual Climate Control System or Dual Automatic Temperature Control System ?
The temperature control switch:
  • is a potentiometer that outputs a variable voltage to the temperature blend door actuator to set the position of the temperature blend door.
  • initiates closing of the heater control valve. When set to full COOL, a lever on the temperature blend door pivot shaft depresses the pintle of the heater control valve vacuum switch. The heater control valve vacuum switch then applies vacuum to the heater control valve, closing off engine coolant flow to the heater core.
  • is serviced only with the climate control assembly.
You may have disturbed something when changing the actuator , the vacuum switch o vacuum hose .

Oct 21, 2015 | 2005 Ford Explorer XLT

1 Answer

My 1998 gmc jimmy slt has a heating problem. The heater wont turn off. As long as the car is on the heater is on full blast. The fans work and everything knob wise works but the heater is always on.


The air temperature valve electronic actuator positions the temperature door according to the temperature setting of the temperature control on the temperature control knob. For the full COLD temperature setting, the temperature control returns approximately 12 volts to the air temperature valve electric actuator. When the temperature setting is changed to full HOT, the temperature door is moved to the warm position and the output drops to about 0 volts. For a temperature setting in the mid range, the temperature door is positioned according to the voltage supplied through the temperature control switch.
Temperature Control Inoperative

2

Inspect the HVAC I fuse 21.
Is the fuse open?
--
Go to Step 20
Go to Step 3

3

  1. Disconnect the air temperature valve sensor.
  2. Turn the ignition switch to the RUN position.
  3. Move the headlamp switch to the PARK position.
  4. Using the J 35616-A , connect a J 39200 Digital Multimeter (DMM) between cavity 8 (CKT 733) of the air temperature valve motor connector and ground.
  5. Move the temperature control knob from the HOT position to the COLD position.
Does the voltage vary smoothly and continuously within the specified range?
0-12 V
Go to Step 4
Go to Step 9

4

Using the J 35616-A , connect a J 39200 DMM between cavity 10 (CKT 341) of the air temperature valve motor connector and ground.
Does the voltage equal the specified value?
B+
Go to Step 5
Go to Step 7

5

Using the J 35616-A , connect a J 39200 DMM between cavity 10 (CKT 341) and cavity 7 (CKT 1850) of the air temperature valve motor connector.
Does the voltage equal the specified value?
B+
Go to Step 6
Go to Step 8

6

Replace the air temperature valve motor.

Aug 31, 2015 | GMC Cars & Trucks

1 Answer

Fan switch location


some models do not have a temperature control switch as it is pre-set in the thermostat to very cold It works to switch off the compressor when the cabin temperature setting is reached.. If it is too cold then the regulation is by the heater control . If it is hot all the time have an accredited ac shop check it for leaks and re-gas the system

Jul 31, 2014 | 2000 Ford Ka

1 Answer

No heating in car


Switch heater on, run engine to temperature, there are two pipes that supply hot water to heater that go through the bulkhead into the cab, feel these pipes to see if they get hot, if yes, then the heater control flaps are stuck closed or the switch control is not working, could be a fuse if they are electrically controlled.

Dec 28, 2013 | 2008 Dodge Avenger

1 Answer

How to replace heater fan control switch on 2000 ford escort zx2


why are you replacing it?

SECTION 412-04: Control Components 2000 Escort Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 08/04/1999
Control Assembly
Special Tool(s) st1445a.gif Remover, Audio Unit
415-001 (T87P-19061-A)
Removal
  1. Disconnect the battery ground cable (14301).
  1. Rotate the temperature control switch to the COOL position.
    al0508a.gif
  1. Disconnect the A/C temperature cable (19988) from the heater core housing.
    1. Unlock the heater temperature cable by pulling down the tab.
    1. Disconnect the heater temperature cable while holding the tab down.
    gl0330a.gif
  1. Use the Radio Removing Tool to pull the integrated control panel out of the instrument panel (04320).
    a0030462.gif
  1. Disconnect the vacuum harness from the function selector switch.
    al0494a.gif
  1. Disconnect the radio antenna lead in cable (18812) and the electrical connectors and remove the control assembly.
    k26305a.gif
Installation
  1. Follow the removal procedure in reverse order.

Dec 20, 2010 | 2000 Ford Escort

2 Answers

I have a mercury mountaineer 2003 V6. It has a problem of making sound repeated when I want to have heat turned on. No sound when the dashboard A.C/Heat stays at AC level, which is the zero? level. The...


When the engine is cold,check the coolant level.

Make sure it's on max.

===

A coolant system should be flush every two years.

===

If you did a coolant flush recently then air pocket can be the cause of the un-even heating problem.

The DIY method is to drive you car onto a ramp or a steep hill.

Iet the engine cool off and top off the coolant tank.

Set MAX heat + MAX fan

Let the engine ran for 20 minutes wih the cap off and the trap air will escape from the coolant reserve tank,

Check coolant level and top off coolant when the engine cools down.



A shop will charge $75+ for this but using an air operated excavate tool!

========

A car with over 90K miles may experience linkage problem to the heater control valve.

The heater control valve (near the firewall) may be stick over time.

Open the hood and move the heater to max and min. Back and forth.

Clean and lube the linkage with WD-40 to free the heater control valve.

If it's a vacuum type heater control valve then cash for leaky vac. hoses.


=======
Move the fan switch back and forth to re-new the electrical conductors.

Pass a vacuum over the control panel to prevent dust build up behind the console.

Sep 13, 2009 | 2003 Mercury Mountaineer

2 Answers

My a/c won't blow cold and heater doesnt get hot


Is the heater working? Turn the A.C. off with the car at an idle. Turn the A.C. on and listen for the compressor to turn on. (should hear a click under the hood and the motor should change pitch. If no noise, the compressor is not comming on. The o-rings were bad about leaking on these cars, letting out all the freeon. If there is no freeon, the low pressure switch won't let the compressor run.

May 20, 2009 | 1997 Ford Taurus

1 Answer

I have a 2000 ford E350 van with front and rear air. the front blower motor runs at low speed, The front blower still runs on low even when the knob is set on medium or high. I do not know where the...


it's either the blower motor switch or blower motor resister. Resistor ?Heater Blower Motor Switch Removal Remove the battery (10655) ; refer to Section 414-01 . Remove the battery tray. Remove the screws. Remove the battery tray. Disconnect the heater blower motor switch resistor connector. Remove the heater blower motor switch resistor (18591). Remove the two screws. Remove the heater blower motor switch resistor. ----------------------------------- Switches Removal Disconnect the battery ground cable. Remove the center trim panel; refer to Section 501-12 . Remove the control assembly. Remove the screws. Remove the control assembly. Remove the A/C-heater function selector switch knob. Disconnect the vacuum harness connector. Disconnect the A/C-heater function selector switch connector. Remove the A/C-heater function selector switch. Remove the screw. Remove the A/C-heater function selector switch. Remove the temperature control switch knob. Disconnect the temperature control switch connector. Remove the temperature control switch. Remove the screw. Remove the temperature control switch. Remove the heater blower motor switch knob. Disconnect the heater blower motor switch connector. Remove the heater blower motor switch (18578). Remove the screw. Remove the heater blower motor switch. ----------------------------

Mar 31, 2009 | 2007 Ford E-350 Super Duty Length XLT

1 Answer

I have the same problem with my windstar blower is fine but is coming cold air but no heat i dont know what to do can any one show me how to fix it thnx


First, feel the heater hoses going into the firewall under the hood. If they are hot, then you have hot engine coolant going into the heater core. If they are not hot, then you either have a bad thermostat or you are very low on engine coolant.

Next you need air flowing through the heater core so it can come out heated through your vents. If the iar is flowing somewhere else, your temp blend door is not moving because the bend door motor is bad or your temp knob on your heater controls is bad. The blend door motor is an electric motor.

------------------------------------------------
Air Flow Control
Air flow control is accomplished in the following manner:
  • Primary control is through the function selector knob , mounted on the heater function selector switch, which is part of the heater control .
  • The function selector knob has the following positions: OFF, PANEL, PANEL/FLOOR, FLOOR, FLOOR/DEFROST and DEFROST.
  • The heater function selector switch combines a vacuum selector valve with an internal electrical switch.
  • The vacuum selector valve directs source vacuum to various vacuum control motors (18A318) . Refer to the System Airflow Schematic and Vacuum Control Charts.
  • An internal single-pole electrical switch is also controlled by the selector. The switch controls the electrical supply to the heater blower motor switch (18578) .
  • The position of the function selector knob determines the manner in which the system will operate.
  • Each position of the function selector knob is detented for positive engagement.
Temperature Control
The temperature control operates in the following manner:
  • Temperature control of the heater system is determined by the position of the temperature control knob (between COOL-BLUE and WARM-RED) of the heater control .
  • This control knob is connected to a potentiometer mounted in the heater control . This potentiometer is electrically connected to the electric blend door actuator that operates the A/C air temperature control door.


e72a310.gif

  • Movement of the control knob from COOL (Blue) to WARM (Red) causes a corresponding movement on the air temperature control door and determines the temperature that the system will maintain.
System uses a reheat method to provide conditioned air to the passenger compartment.
  • All airflow from the blower motor (18527) passes through the A/C evaporator housing .
  • Temperature is then regulated by reheating a portion of the air and blending it with the remaining cool air to the desired temperature.
  • Temperature blending is varied by the air temperature control door, which regulates the amount of air that flows through and/or around the heater core (18476) , where it is then mixed and distributed.
--------------------------------------------------------------------------------------------------------------------------
inside you plenum box:

09f3f8a.gif

Mar 03, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Dave  C
Dave C

Level 3 Expert

1050 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...