Question about 1985 Ford F 250

1 Answer

Power steering pump

Trying to re-install this pump. I seemed to have forgot how the brackets assemble back together. Can someone help me with a belt diagram. I have the bracket on the pump correct. But there are two other brackets to put back together.
Thanks
George

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,035 Answers

Please click on this link:

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528004bdfb


Good luck hope this link will help you , have a good day going....

Posted on Jul 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Im trying to change my alternator on my 97 chrysler sebring coupe lxi but it seems impossible to do it without taking other parts off to get it out and also put the new one in because its real compact


Hi there:
Check this procedure on 2.5L (VIN N) Engine...


  1. Disconnect the negative battery cable.
  2. Remove the right side under cover.
  3. Remove the speed control vacuum reservoir and related components as required for alternator access.
  4. Remove the power steering pump cover.
  5. Remove the A/C compressor drive belt.
  6. Remove the alternator/power steering pump drive belt.
  7. Remove the intake manifold plenum.
  8. Remove the upper alternator bracket.
  9. Remove the intake manifold plenum stay.
  10. Detach the electrical connections at the alternator.
  11. Unfasten the upper and lower bolts and remove the alternator. Be very careful not to damage neighboring components while removing the alternator.


8_22_2012_2_51_45_pm.gif

Fig. 8: Alternator assembly installation-2.5L engine (VIN N) - Zoom Image link HERE


To install:

  1. Connect the wiring to the alternator.
  2. Place the alternator on its lower bracket and install the upper and lower bolts finger-tight.
  3. Install the upper alternator bracket.
  4. Install the alternator/power steering pump belt, making sure it is properly seated.
  5. Adjust the drive belt to the correct tension using the belt adjuster, then tighten the upper mounting bolt to 16 ft. lbs. (22 Nm) and the lower mounting bolt to 30 ft. lbs. (41 Nm).
  6. Install the intake manifold plenum.
  7. Install the intake manifold plenum stay.
  8. Install the A/C compressor drive belt.
  9. Install the power steering pump cover.
  10. Connect the negative battery cable.
  11. Check the charging system operation.



Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 22, 2012 | Cars & Trucks

1 Answer

How to install a power steering pump for a 1997 chrysler seabring conv


Chrysler Cirrus/Stratus/Sebring/Avenger/Breeze 1995-1998
Power Steering Pump - REMOVAL & INSTALLATION

Cirrus, Stratus, Sebring Convertible and Breeze
(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with an insulator grommet, which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Siphon as much power steering fluid out of the reservoir as possible.
  3. Raise and safely support the vehicle.
  4. Remove the right front tire and wheel assembly.
  5. Remove the splash shield from the right front wheel well.
c901554.jpg

Fig. 1: Power steering pressure hose attachment to the pump-with Variable-Assist steering

8786c07.jpg

Fig. 2: Power steering pressure hose attachment to the pump-without Variable-Assist steering
  1. Disconnect the power steering pressure hose from the pump.
  2. Remove the hose connection on the power steering pump.
e7733b2.jpg

Fig. 3: Typical power steering pump front bracket attachment
  1. Remove the power steering adjusting bolt.
  2. Remove the power steering pump rear attaching bolt.
  3. If so equipped, remove the Anti-lock Brake System (ABS) hydraulic control unit heat shield.
  4. Remove the wheel speed sensor retainer bracket from the right inner fender.
  5. Remove the wheel speed sensor sealing grommet from the right inner fender.
  6. Disconnect the speed sensor wiring.
  7. Push the wiring through the hole in the inner fender.
If not equipped with anti-lock brakes, the hole will just have a sealing plug.
  1. Remove the bolt attaching the power steering front bracket to the mounting bracket. Access to the bolt is gained through the hole for the speed sensor wiring.
  2. Remove the power steering pump drive belt.
  3. Remove the power steering pump and the front bracket as an assembly.
To install:
  1. Install the power steering pump and bracket.
  2. Reinstall the bolt at the adjusting slot, but do not tighten.
  3. Reinstall the bolt mounting the power steering pump to the rear mounting bracket, but do not tighten.
  4. Reinstall the power steering pump top bolt, but do not tighten.
  5. Reconnect the power steering hoses.
b72b14a.jpg

Fig. 4: Install a new O-ring gasket on the hose fitting
Use a new O-ring when reinstalling the power steering pressure hose.
  1. Reinstall the drive belt.
  2. Adjust the drive belt and tighten the power steering pump bolts to 40 ft. lbs. (54 Nm).
  3. Reinstall the splash shield.
  4. Reinstall the tire and wheel assembly.
  5. Lower the vehicle.
  6. Reconnect the negative battery cable.
  7. Refill the reservoir and bleed the power steering system.


Sebring Coupe and Avenger
  1. Disconnect the negative battery cable.
  2. Remove (drain, suction pump, etc.) as much power steering fluid as possible.
  3. Disconnect the return fluid line. Remove the reservoir cap and allow the return line to drain the fluid from the reservoir. If the fluid is contaminated, disconnect the ignition high tension cable and crank the engine several times to drain the fluid from the gearbox.
Cover any components located underneath the power steering pump with a shop towel to protect them from damage due to power steering fluid spillage. For example, the A/C compressor or alternator, depending on vehicle and engine, is below the power steering pump, so cover the A/C compressor or alternator with a shop towel before removing any hoses.
  1. Loosen (but do not remove) the power steering pump mounting bolts and remove the drive belt.
  2. Remove the pressure switch connector from the side of the pump.
  3. Disconnect the pressure line.
  4. Unbolt and remove the pump from the mounting bracket.
To install:
  1. Clean all parts well. Inspect the pump pulley for cracks. Check the hoses carefully for cracks or signs of weakness.
  2. Install the pump, wrap the belt around the pulley and lightly tighten the mounting bolts.
  3. Replace the O-rings and connect the pressure line. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the fitting to 13 ft. lbs. (18 Nm).
  4. Connect the return line and secure with the clamp.
  5. Fasten the pressure switch connector.
  6. Adjust the power steering belt for proper tension and tighten the adjusting bolts.
Use only MOPAR ATF PLUS automatic transmission fluid type 7176, ATF+3 automatic transmission fluid, or equivalent, in the power steering system of Sebring coupe and Avenger models.
  1. Refill the reservoir and bleed the power steering system.

Hope this help to solve it (remember comment and rated this). TY for using Fixya.

May 13, 2010 | 1997 Chrysler Sebring

2 Answers

Looking to see haw difficult it is to change power steering pump.? any ideas Iam some what mechanicaly inclined


GM Astro/Safari 1985-1996 Repair Guide
Power Steering Pump - REMOVAL & INSTALLATION
(see Figures 1, 2, 3, 4, 5, 6 and 7)

199f8a3.jpg

Fig. 1: Exploded view of the power steering pump assembly mounting-2.5L engine

1544b7a.jpg

Fig. 2: Exploded view of the power steering pump assembly mounting-early-model 4.3L engine

8c93529.jpg

Fig. 3: Removing the power steering pump pulley-1985-92 vehicles

1995aea.jpg

Fig. 4: Installing the power steering pump pulley

d000dbb.jpg

Fig. 5: Pump pulley removal and installation-1993-96 vehicles

e8e94e6.jpg

Fig. 6: Exploded view of the power steering pump mounting-late-model 4.3L engines (1993-96 shown)

44caf14.jpg

Fig. 7: Typical power steering pump hose routing-1996 shown


The following procedure requires the use of the GM Puller tool No. J-29785-A (1985-92), Puller J-25034-B (1993-96) or equivalent, and the GM Pulley Installer tool No. J-25033-B or equivalent.
  1. Disconnect the negative battery cable for safety.
  2. For 1996 vehicles, remove the air cleaner assembly for access.
  3. For 1993-96 vehicles, remove the hood latch and the upper fan shroud.
  4. Release tension and remove the drive belt.
  5. Remove the power steering pump pulley using a suitable puller tool.
  6. Remove the power steering pump retaining bolts, then reposition the pump as necessary for access to the hoses.
  7. Position a fluid catch pan under the power steering pump.
  8. Remove the hoses from the power steering pump and drain the excess fluid into the catch pan.
WARNING Be sure to cap all openings in the pump hydraulic system to prevent excessive fluid spillage and the possibility of system contamination.
  1. Remove the power steering pump from the vehicle.
To install:
  1. Position the pump to the vehicle, then uncap and connect the pump hoses.
  2. Install the steering pump to the retaining bracket, then secure using the retaining bolts. Tighten the power steering pump-to-bracket bolts to 37 ft. lbs. (50 Nm). For 1996 vehicles, tighten the nut to 30 ft. lbs. (41 Nm).
On early-model vehicles where the drive belt is tensioned by pivoting the power steering pump assembly, do NOT fully tighten the mounting bolts at this time, since you will just have to loosen them again for belt installation and adjustment.
  1. Install the pump pulley using the GM Pulley Installer tool No. J-25033-B or equivalent. Press the drive pulley onto the power steering pump.
  2. Hand-tighten the pivot bolt, the adjusting bolt and the washer.
  3. Install the drive belt. On early-model vehicles so equipped, properly adjust the belt tension. For details on belt installation and tension adjustment.
  4. For 1993-96 vehicles install the upper fan shroud and the hood latch assembly.
  5. For 1996 vehicles, install the air cleaner assembly.
  6. Connect the negative battery cable.
  7. Refill the power steering reservoir and bleed the power steering system.
  8. Remove the jackstands and carefully lower the vehicle.
  9. Road test the vehicle, then check and top-off the power steering fluid.

hope this help (remember rated this post) Good luck.

May 13, 2010 | 1989 GMC Safari

3 Answers

How do you remove the Power Steering Pump and bracket. I have taken off several bolts but it still is not letting loose. Help


3.0L (VIN 3) Engine

f799ffc.gif
Power steering pump mounting detail (3.0L engine)

  1. Disconnect and isolate the negative battery cable.
  2. Remove the accessory drive belt. The belt does not have to be removed from the engine.
  3. Raise and safely support the vehicle.
  4. Disconnect the wiring harness connector to the oxygen sensor which is accessible through the oxygen sensor wiring harness grommet in the vehicle floor pan.
  5. Remove the catalytic converter from the exhaust manifold and remove all exhaust system hangers and isolators from the exhaust system brackets. Move exhaust system out of the way as far rearward and to the left as possible to provide access to the power steering pump.
  6. Place a drain pan under the power steering pump. Remove the power steering fluid return line hose on the front suspension cradle. Allow the fluid to drain from the pump and hose.
  7. Remove the accessory drive belt splash shield.
  8. Disconnect the power steering remote reservoir supply hose from the fitting on the power steering pump. Allow fluid to drain from the hose.
  9. Remove power steering fluid pressure line from the power steering pump and drain any excess power steering fluid.
  10. Remove the power steering fluid return hose from the power steering pump.
  11. Remove the rear support bracket mounted behind the power steering pump to the engine block.
  12. Remove the 2 mounting bolts that secure the pump to the alternator/power steering pump and belt tensioner mounting bracket.
  13. Remove the power steering pump and pulley assembly out from the vehicle. Transfer all required parts from the pump to the new replacement pump before installation.
To install:
  1. Position the front of the power steering pump up onto the mounting bracket. Torque the 2 power steering pump-to-mounting bracket bolts to 40 ft. lbs. (54 Nm).
  2. Install the rear power steering pump-to-engine block support bracket. Torque the 2 support bracket mounting bolts to 40ft. lbs. (54 Nm). Install the nut to the mounting stud behind the pump and torque to 40 ft. lbs. (54 Nm).
  3. Install the high pressure fluid line to the pump output fitting. Torque the high pressure line-to-power steering pump fitting to 275 inch lbs. (31 Nm). Be sure to inspect the pressure line O-ring for any damage before connecting the pressure line to the steering pump.
  4. Install the low pressure power steering fluid hose to the power steering pump low pressure fitting. Be sure the hose clamps are properly reinstalled and hoses are clear of the accessory drive belts.
  5. Install the accessory drive belt.
  6. Install the hose on the power steering fluid return line on the front suspension cradle. Be sure the hose clamps and heat shield tubes are correctly reinstalled.
  7. Reconnect the exhaust pipe to the exhaust manifold. Install the hangers and isolators onto the exhaust system brackets. torque the nuts and bolts to 250 inch lbs. (28 Nm).
  8. Reconnect the wiring harness connectors to the oxygen sensor. Install the wiring harness grommet into the vehicle floor pan.
  9. Install the accessory drive belt splash shield.
  10. Remove the drain pan and lower the vehicle.
  11. Refill the power steering pump reservoir with the correct amount of clean power steering fluid.
  12. Reconnect the negative battery cable. Bleed the power steering system.
  13. Run the engine and check the system for leaks and proper steering operation.

3.3L (VIN R) & 3.8L (VIN L) Engines

0b3de97.gif
Rear support bracket mounting detail (3.3 & 3.8L engines)

6764c64.gif
Power steering pump mounting detail (3.3 & 3.8L engines)

  1. Remove and isolate the negative battery cable.
  2. Raise and safely support the vehicle. Place a drain pan under the power steering pump.
  3. Disconnect the wiring harness connector to the oxygen sensor which is accessible through the oxygen sensor wiring harness grommet in the vehicle floor pan.
  4. Remove the catalytic converter from the exhaust manifold and remove all exhaust system hangers and isolators from the exhaust system brackets. Move exhaust system out of the way as far rearward and to the left as possible to provide access to the power steering pump.
  5. Remove the power steering fluid return line hose on the front suspension cradle. Allow the fluid to drain from the pump and hose.
  6. Remove the accessory drive belt splash shield.
  7. Remove accessory drive belt.
  8. Disconnect the power steering remote reservoir supply hose from the fitting on the power steering pump. Allow fluid to drain from the hose.
  9. Remove power steering fluid pressure line from the power steering pump and drain any excess power steering fluid.
  10. Remove the power steering fluid return hose from the power steering pump.
  11. Remove the rear support bracket mounted behind the power steering pump to the engine block.
  12. Remove the 3 mounting bolts that secure the pump to the alternator/power steering pump and belt tensioner mounting bracket.
  13. Remove the power steering pump and pulley assembly from the vehicle. Transfer all required parts from the pump to the new replacement pump before installation.
To install:
  1. Position the front of the power steering pump up onto the mounting bracket. Torque the 3 power steering pump-to-mounting bracket bolts to 40 ft. lbs. (54 Nm).
  2. Install the rear power steering pump-to-engine block support bracket. Torque the support bracket mounting bolts to 40 ft. lbs. (54 Nm). Install the nut to the mounting stud behind the pump and torque to 40 ft. lbs. (54 Nm).
  3. Install the high pressure fluid line to the pump output fitting. Torque the high pressure line-to-power steering pump fitting to 275 inch lbs. (31 Nm). Be sure to inspect the pressure line O-ring for any damage before connecting the pressure line to the steering pump.
  4. Install the low pressure power steering fluid hose to the power steering pump low pressure fitting. Be sure the hose clamps are properly reinstalled and hoses are clear of the accessory drive belts.
  5. Install the accessory drive belt.
  6. Install the hose on the power steering fluid return line on the front suspension cradle. Be sure the hose clamps and heat shield tubes are correctly reinstalled.
  7. Reconnect the exhaust pipe to the exhaust manifold. Install the hangers and isolators onto the exhaust system brackets. Torque the nuts and bolts to 250 inch lbs. (28 Nm).
  8. Reconnect the wiring harness connectors to the oxygen sensor. Install the wiring harness grommet into the vehicle floor pan.
  9. Install the accessory drive belt splash shield.
  10. Remove the drain pan and lower the vehicle.
  11. Refill the power steering pump reservoir with the correct amount of clean power steering fluid.
  12. Reconnect the negative battery cable. Bleed the power steering system.
  13. Run the engine and check the system for leaks and proper steering operation.

Nov 03, 2009 | 1997 Chrysler Town & Country

1 Answer

Replace power steering pump


NOTE: The following procedure requires the use of the GM Puller tool No. J–29785–A (1985–92), Puller J–25034–B (1993–96) or equivalent, and the GM Pulley Installer tool No. J–25033–B or equivalent.
  1. Disconnect the negative battery cable for safety.
  2. For 1996 vehicles, remove the air cleaner assembly for access.
  3. For 1993–96 vehicles, remove the hood latch and the upper fan shroud.
  4. Release tension and remove the drive belt. For details, please refer to Section 1 of this manual.
  5. Remove the power steering pump pulley using a suitable puller tool.
  6. Remove the power steering pump retaining bolts, then reposition the pump as necessary for access to the hoses.
  7. Position a fluid catch pan under the power steering pump.
  8. Remove the hoses from the power steering pump and drain the excess fluid into the catch pan.
  9. WARNING
    Be sure to cap all openings in the pump hydraulic system to prevent excessive fluid spillage and the possibility of system contamination.
  10. Remove the power steering pump from the vehicle. To install:
  11. Position the pump to the vehicle, then uncap and connect the pump hoses.
  12. Install the steering pump to the retaining bracket, then secure using the retaining bolts. Tighten the power steering pump-to-bracket bolts to 37 ft. lbs. (50 Nm). For 1996 vehicles, tighten the nut to 30 ft. lbs. (41 Nm). NOTE: On early-model vehicles where the drive belt is tensioned by pivoting the power steering pump assembly, do NOT fully tighten the mounting bolts at this time, since you will just have to loosen them again for belt installation and adjustment.
  13. Install the pump pulley using the GM Pulley Installer tool No. J–25033–B or equivalent. Press the drive pulley onto the power steering pump.
  14. Hand-tighten the pivot bolt, the adjusting bolt and the washer.
  15. Install the drive belt. On early-model vehicles so equipped, properly adjust the belt tension. For details on belt installation and tension adjustment, please refer to Section 1 of this manual.
  16. For 1993–96 vehicles install the upper fan shroud and the hood latch assembly.
  17. For 1996 vehicles, install the air cleaner assembly.
  18. Connect the negative battery cable.
  19. Refill the power steering reservoir and bleed the power steering system.
  20. Remove the jackstands and carefully lower the vehicle.
  21. Road test the vehicle, then check and top-off the power steering fluid.
Fig. 3: Removing the power steering pump pulley — 1985–92 vehicles

213c6a5.jpg
Email me at greg.bernett@mcchord.af.mil for an engine picture breakdown.

    Jul 22, 2009 | 1990 GMC Safari

    1 Answer

    Changing power steering pump


    Power steering pump special tools

    519a4ae.gif
    Power Steering Pump Removal & Installation Power Steering Pump (2V) To Remove:
    1. Before servicing the vehicle refer to the precautions at the beginning of this section.
    2. Disconnect the battery ground cable.
    3. Remove the accessory drive belt.
    4. Remove the alternator.
    5. Drain and remove the radiator coolant recovery reservoir.
    6. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
    7. Remove the idler pulley from the power steering pump support.
    8. Remove the belt tensioner.
    9. Remove the bracket mounting bolt located under the belt tensioner mounting.
    10. Remove two retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
    11. Clamp the pump support bracket in a suitable vise.
    12. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the three bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.

    To Install:
    NOTE: The pulley must be installed within 0.010 in (0.25 mm) flush with the power steering pump shaft.

    1. Install the power steering pump to the power steering pump support. Tighten the mounting bolts to 18 ft-lb. (25 Nm).
    2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
    3. Install the power steering pump/pump support and torque nuts/bolt to 24 ft. lbs. (33 Nm).
    4. Install the bracket mounting bolt located under the belt tensioner mounting.
    5. Install the belt tensioner.
    6. Install the idler pulley to the power steering pump support.
    7. Connect the hydraulic pressure and return lines.
    8. Install the radiator coolant recovery reservoir.
    9. Install the alternator.
    10. Install the accessory drive belt.
    11. Fill the power steering reservoir with power steering fluid.
    12. Connect the battery ground cable.
    13. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.

    Jun 28, 2009 | 1999 Ford Taurus

    2 Answers

    The power steering pump bolts all seem to have vibrated out, the unit came free and i can just move it around, the pulley moves freely, everything else seems to work ok


    I don't have chrysler producs. I'll post 3.8L V6 Ford Windstar for reference. You'll get some idea.



    Removal
    ssw~us~en~file=ani_caut.gif~gen~ref.gif WARNING: USE CAUTION WHEN REMOVING OR INSTALLING DRIVE BELT TO MAKE SURE THAT TOOL DOES NOT SLIP.
    1. Using a 15mm socket or wrench on bolt attaching drive belt tensioner pulley. Rotate drive belt tensioner (6B209) clockwise to remove drive belt from pulleys.

      3.8L Engine

      e973ba6.gif
    Item Part Number Description 1 10300 Generator 2 3A674 Power Steering Pump 3 19703 A/C Compressor 4 6B217 Drive Belt Tensioner Pulley 5 6312 Crankshaft Pulley 6 8501 Water Pump 7 6B209 Drive Belt Tensioner 8 8620 Drive Belt
    Installation
    1. Install drive belt over all pulleys (except drive belt tensioner ).
    1. Rotate drive belt tensioner as described under Removal and install drive belt over drive belt tensioner pulley. Ensure that all V-grooves make proper contact with pulleys
    ---------------------------------------------------------------
    Another example
    Pulley, Power Steering Pump CII
    SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Steering Pump Pulley Remover T69L-10300-B Steering Pump Pulley Replacer T65P-3A733-C
    Removal
    1. Drain as much fluid as possible from the power steering pump (3A674) through the power steering oil reservoir (3A697) neck.
    1. Install Steering Pump Pulley Remover T69L-10300-B on the power steering pump pulley (3A733) , and place the tool and power steering pump in a vise by gripping the small hex-head of the tool.
    1. Hold the power steering pump , and rotate the tool nut counterclockwise to remove the power steering pump pulley . Do not apply in and out pressure on the power steering pump shaft. Pressure will damage the internal thrust areas.

    Installation
    ssw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal thrust areas.
    1. Place the power steering pump pulley on the power steering pump shaft, and install Steering Pump Pulley Replacer T65P-3A733-C. The small diameter threads on the tool should be fully engaged in the power steering pump shaft.
    1. Hold the power steering pump , and rotate the tool nut clockwise to install the power steering pump pulley on the shaft. The power steering pump pulley face must be flush within 0.25mm (0.010 inch) of the end of the power steering pump shaft.
    1. Remove the tool.
    1. Fill the power steering oil reservoir to the COLD FILL line.
    ------------------------------------------------------------------------------------------
    Steering Pump, Power Removal
    1. Disconnect battery ground cable (14301) .
    1. Remove accessory drive belt (8620) .
    1. Raise vehicle on hoist. Refer to Section 00-02 .
    1. Remove right front wheel (1007) and tire assembly.
    1. Remove power steering pump pulley (3A733) .
    1. Position drain pan. Remove power steering pressure hose (3A719) and power steering return hose (3A713) from power steering pump (3A674) .
    1. Remove four power steering pump retaining bolts (three in front, one in rear) and remove power steering pump .
    Installation
    1. Position power steering pump and install retaining bolts. Tighten retaining bolts to 41-54 Nm (30-40 lb-ft).
    1. Install power steering pressure hose and power steering return hose to power steering pump . Remove drain pan.
    1. Press on power steering pump pulley as outlined in this section.
    1. Install right front wheel and tire assembly. Tighten lug nuts (1012) to 115-142 Nm (85-105 lb-ft).
    1. Lower vehicle.
    1. Install drive belt to power steering pump pulley .
    1. Connect battery ground cable .
    1. Fill power steering oil reservoir (3A697) to proper level. Refer to Section 11-00 .

      Power Steering Pump and Bracket, 3.8L

      17c7689.gif
    Item Part Number Description 1 N607528-S2 Screw, M6-1 x 16 2 8509 Water Pump Pulley 3 W804804-S2 Screw, M8-1.25 x 35 4 N806214-S2 Bolt, M12 5 W606691-S36B Screw, M8-1.25 x 35 6 10B315 Generator Brace 7 N621939-S36B Nut, M8-1.0 8 10300 Generator 9 6B212 Accessory Drive Belt Tensioner Bracket 10 6049 Cylinder Head 11 19D624 Air Conditioning Compressor Bracket 12 W606563-S2 Bolt, M10-1.5 x 55 13 19703 A/C Compressor 14 N807273-S100 Bolt, M8-1.25 x 121.5 15 3C510 Power Steering Hose Bracket 16 3A674 Power Steering Pump 17 3C511 Power Steering Pump Support 18 W807239-S8 Bolt, M10-1.5 x 36.5 19 2888 A/C Compressor Brace 20 W806342-S2 Bolt, M8-1.25 x 23 21 W606571-S411 Bolt, M10-1.5 x 113.5 22 6C348 Idler Assembly 23 3A733 Power Steering Pump Pulley 24 N805137-S56 Bolt, M10-1.5 x 157 25 N621939-S2 Nut, M8-10 26 N807241-S36B Bolt, M10-1.5 x 132 27 6B209 Drive Belt Tensioner A — Tighten to 8-11 Nm (71-101 Lb-In) B — Tighten to 20-25 Nm (15-18 Lb-Ft) C — Tighten to 70-95 Nm (52-70 Lb-Ft) D — Tighten to 40-55 Nm (30-40 Lb-Ft) E — Press Flush with End of Power Steering Pump Shaft

    Mar 03, 2009 | 1994 Plymouth Voyager

    1 Answer

    96 landrover disco power steering pump bracket broken off


    Really stupid question but did you get the correct belt and did you adjust the belt tensioner? On vehicles with spring type tensioner it must be pried back and then released. Slide type tensioners are usually either part of the pump bracket or alternator bracket assembly.

    Dec 07, 2008 | 1996 Jeep Grand Cherokee

    2 Answers

    Water pump assembly and power steerin pump brackets


    need to know year? engine size?what accesories equipped? a/c power steer smog pump etc.

    Aug 26, 2008 | 1989 Dodge Ramcharger

    Not finding what you are looking for?
    Cars & Trucks Logo

    82 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    60792 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Fordexpert

    Level 3 Expert

    5331 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...