Question about Chevrolet Malibu

1 Answer

High torque mini starter

i sent the question for help but i don't understand what you are telling me can you make a scetch to make it a more simple for a dummass like me. this car is my pride and joy plus theropy for my severe depression and when i can't figure it out it really upsets me so your help is really appreciated.

thanks again,
mitchell kearns

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has written 50 answers of more than 400 characters.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 126 Answers

Im not shure what it is you need to do ? what picture are we looking to see ? give me some more information ok ill do my best to help u get baby rollin once again ok

Posted on Jul 06, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Whenever I let my 2010 toyota camry sit for several hours, it makes a winding noise and idles high when I first start it up. What could be causing this.

starter problem

2010 Toyota camry use hi torque starters

will wind over faster .
.if noise is very audible
have starter checked over or rebuilt or replace

idle problem
local weather conditions and old 02 sensors can cause hi idle
motor idle is controlled by the idle control sensor ( IAC) and can be cleaned
..if solenoid part is faulty ..non adjustable trow away part
replace unit



Oct 07, 2016 | Toyota Cars & Trucks

1 Answer

My 2005 avalanche wont shift right and the tach doesnt work

I highly doubt the tachometer has anything to do with what you are explaining. Did they go out at the same time? Could be your torque converter gone bad, could be you just need to get the tranny serviced (usually about 80.00 dollars at your transmission shop). They will flush fluids, and replace filter. this could fix your problem. If you don\'t trust the transmission shop, don\'t tell them what its doing, if you can help it, when you drop off. Just tell them you want the flush and replacement of filter service. If its still doing it after that, then you will have to start looking at more $ to fix. Good luck

Mar 06, 2013 | 2005 Chevrolet Avalanche

1 Answer

Is there a torque spec for front end cv axle nut to hub on 2000 Plymouth Neon

  • Yes there is a torque spec of 180 foot lbs. is recommended. I highly suggest never using an impact for the hub to axle application. If you don't use a properly calibrated torque wrench you could have problems in the future.

  • Hope this helps.

Nov 04, 2011 | 2000 Plymouth Neon

1 Answer

I am trying to replace the starter in a 2000 nissan sentra SE. However I can not find anything to tell me how I need to do this. Can you help?

first you need to get car on ramps or blocked up high enough for you to get under ,or you might be able to get from top side but ive found it better to go under car.once you have car up then DISCONNECT BATTERY,once you located starter,you will need either a star bit or alan bit ,some have torques head,once you have desired bit remove bolts usaly 2 one on each side and sometimes a center support bolt,then slowy pull starter out so you can get to wires on starter pls close attention to ware wires are located on each terminal,NOTE A CAMERA PHONE MAKES IT EASY,so you can put them back on correctly,once wires are off and starter is free,you can replace starter with new one,putting wired back on rt terminal THIS IS WARE YOUR CAMERA PHONE COMES IN USE,place starter back in ,NOTE WHEN YOU TAKE STARTER OUT THERE MAYBE LITTLE METAL TABS ON BOLT THESE ARE CALLED SHIMS YOU MAY HAVE TO REPLACE THESE SHIMS DEPENDING ON WHAT KIND OF SHAPE THEY ARE IN,put bolts back in tighten ,you can use a torque wrench or just tighten real tight ,their is torque specs for starter refeer to manual or call delearship they will be glad to tell you specs for free,once you have starter in connect battery,then start car,if starter is noisy when starting then you may have to loosen bolts and put shim in,hope ive helped you not confused you

Jul 07, 2011 | Nissan Sentra Cars & Trucks

1 Answer

2003 mazda 6 3.0 need the main bearing torque specs

I'm sending you the torque specifications for your main bearings and also your head bolts. I also sent you main bearing and cylinder head tightening sequence. I hope this will be useful2c713bf.giffce6623.gif
Main Bearings Torque specs. 40-43 Ft. Lbs.
Cylinder Head Torque specs. 56-60 Ft. Lbs.

Oct 05, 2009 | 2003 Mazda Mazda6

2 Answers

Head bolt torque settings...

Stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)

Buy new bolts first tho

Jun 28, 2009 | 2001 Isuzu Rodeo

1 Answer

1972 chevelle starter trouble

Since you have replaced the starter motor with a higher torque one then the next approach that I would take would be to inspect the flywheel teeth. It sounds like maybe these teeth could be damaged or even missing. If this is the case it requires you to get a new flywheel.

Jun 09, 2009 | 1972 Chevrolet Corvette

3 Answers

2005 aveo got code on transmishion p 0300 p 0700 and p1781

It sounds like you have a problem with your crank sensor or cam sensor!! You will have to take to a dealer that knows how to learn the crank sensore.. Yes it has to be learned into the computer.

Also there was a sevice bulletn on mising being that the intake valves needed to be replaced and reseated.

The transmission code is being sent because of the randome missing.. so it will not upshift into I think 4th (lockup). and the other is sent to torque because of the random miss also..

Solution!!!!!!! take to dealer and have them relearn crank sensor!!!

Hope this helps

Jun 03, 2009 | 2005 Chevrolet Aveo

1 Answer

1966 chevelle with 283 cu. in.

the r terminal only has 12 volts on it when you are cranking the starter over. so the wire that goes to the r terminal goes to the plus side of the coil then the wire that come from the switch also goes to the coil this wire should have only about 8.5 volts on it when switch is in run position the r terminal puts 12 volt on the coil while cranking the motor over the when the switch is in the run position there is 8.5volt on the points so you don't burn the points out the diode kit i don't no why you need it unless the don't what any back feed volt to the r terminal in the run position so i would put it in line(series) with the r terminal wire the flow on the diode is from the -<- this side of the diode goes to the coil

Jul 03, 2008 | Chevrolet Malibu Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides