Question about 1998 Ford F150 Regular Cab

1 Answer

Super cab, 4.6 liter 4X4. How do I remove the C-clips on the rear axels?

There is some kind of S shaped spring in there that prevents access to the c-clip.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 55 Answers

If you turn then gears just right the clips slide out. That clip has a lot of tension on it so be careful once they're out. It pretensions the limited slip.

Posted on Oct 16, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace bearing in a 1991 chevy 1500 4x4 rear axel at driveshaft?


To replace pinon bearing you need to pull wheels and the brake drums off next pull cover off the back of the rear end (make sure you have a drain pan under rear end) next turn dive shaft till you see a small bolt remove bolt pull center pin out push axle in pull c clips out pull axels out remove four bolts holding ring and spider gears remove gears assembly next remove drive shaft remove bolt from pinon push pinon in remove seal and bearing

Jun 27, 2011 | 1991 Chevrolet K1500

1 Answer

On the 4x4 front axel whats the procedure to remove upper & lower ball joints. now ive got the hub out both up & low joints free but because of the axel yoke wont go toward the wheel ? how do...


THE AXLE HAS TO COME OUT OF SPINDLE USE A PRY BAR BEHIND THE AXLE AND PRY IT OUT OF THE SPINDLE IF THIS IS A VACCUM OPERATED SPINDLE THE SEAL WILL (HAS TO ) COME OUT

Oct 17, 2010 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

I have 2001 Chev Tracker, Oil started to run out of the Right side break drum. Removed Drum and foud oil all over the breaks. Tried to remove the Axel by removing the four nuts off of the backing plate,...


fror fixing the brakesw take the other rear wheel off and duplicate what u see. to get the axel out u must first remove diff cover in center of rearend then u will see a clip for each side axel remove clip and axel will slide out. good luck fron 1 to 5 being difficult its a 3

Jul 21, 2010 | 2002 Chevrolet Tracker

1 Answer

1995 chevrolet tahoe 4x4 posi rearend axel bearing replacement how do i remove the posi unit to get the axels out?


You don't. Ever work on a rear axle. Remove cover,one bolt,pull pin and axle clip.Then pull axle, and off to auto parts store, to press on new bearing.

Feb 13, 2010 | 1995 Chevrolet Tahoe

2 Answers

F250 4X4 MANUAL HUBS WILL NOT ENGAGE ALSO HAVING


im not sure if a 2000 f150 and a 2000 f250 have the exact steering column,but incase it is then check at the base of the column inside and you may see a triangler shape bracket that the shift cable connects to,there will be 2 torque screws holding the bracket to the column,either a t-20 or t-25 not sure,they may be loose so the shifter will be sloppy...my 2000 f150 had that problem and i stumbled upon it,it seems to be a 2000 year issue...about the manual hubs,try locking them in and drive forward and reverse very slow a few times,if they lock in then they are sticky and it takes time for the spring inside to push then together.lock the hubs in first,then after a while shift to 4x4,because if they are just sticky,it may strip the teeth on the lockouts from the axel turning against the inside of the lockout.

Feb 07, 2010 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

The axle from a jeep 4x4 is broke , both axles, how do i take out the rest of the parts?


The front axel is a two piece assy. remove the 4wd
shift moter from the axel housing. Once the moter
and fork are off , remove outer axel.To remove inner
axel, remove differential cover and let it drain.
There is a C clip on the axel, remove it and work the
axel out through the axel tube.(if it is broken)
To remove the rear axel. Remove diff. cover and drain.
Remove the pinion lock nut(or spring clip) and slide
back pinion shaft. Remove retaining clip from axel
and remove axel. To remove broken piece I use to
use a length of an old whip antenna, to push it out.
If you can find a piece of heavy gauge wire to push
it out.(a plumbers snake may work)Also only have
one axel at a time out of either housing, this will
make it easier to reinstall the axels.
I hope I was of some help. Good luck.

Jan 30, 2010 | 1995 Jeep Grand Cherokee

1 Answer

Removing door panels on 2003 ford ranger 4 dr


It's usually the window winder that presents the problem . Remove all visable retaining screws ie; Grab handle , Internal door opening lever , Button on top of panel (if applicable ) etc . The majority panel are a pop snap on type . Remove the winder lever withthe aid of a shoe lace or thin piece of cloth material, The winder is retained by a horse-shoe shaped spring clip. .... Pull the shoe-lace/ material in the opposite direction of the winder retainer clip and it will easily come off, but it is a spring clip and may fly off so be careful. Good luck

Dec 30, 2009 | 2003 Ford Ranger Regular Cab

1 Answer

How to remove rear axle 03 chevy silverado


You will have to remove the rear end plate off of the back of the rear end. Then turn the carrier untill you see a big silver pin that goes through the spider gears. Those will be 4 small gears in the rear end carrier. If you look at the right side of the carrier were the pin goes through it you will see a small bolt head, That bolt goes through the carrier and holds the pin in place. Remove that bolt then reach up in the rear end housing and push the pin towards you untill it comes out. ( DO NOT TURN ANYTHING AFTER YOU REMOVE THE PIN) are the spider gears will fall out.


Now get someone to push the axel in while you are looking at the 4 small gears in the housing, when they push the axel in a C-clip will fall off the end of the axel and into the rear end, You will see it fall out. Then just pull the axel out.



When you put the axel back in, push it all the way in then slide the c-clip over the end of the axel and then pull out on axel and that will hold the clip in place untill you put the big long pin back in the carrier. I hope you understand, just watch what you are doing. GOOD LUCK.

Oct 09, 2009 | 2003 GMC Yukon

1 Answer

Grease and differential oil inside left rear drum


Not that difficult, raise and support the rear of the truck and remove the wheels. Might as well replace both sides so you know you have new seals, remove the differential cover and drain the fluid. Once differential is opened and cleaned , remove the axle "C" clip that hold the axle in place and slide the axle out. Once the axle is out remove the wheel seal and clean around the area. This would be a good time to replace the wheel bearing too since you have access to them and there not that expensive. Install the new bearing and seal, note make sure you oiled the bearing and seal before installing it back and take care when installing the axle back in and "C: clip. Use RTV silicon gasket maker to seal the differential cover and wheels back on and lower. If your lazy like i am, you can drain the differential fluid and replace it with a 50/50 mix with gear oil and Lucas engine oil additives. That may stop the leak and get you a few more miles. You gear oil is (ford 75W-140) (Dana 80W-90)and the capacity is 2.6 liters and 3.5 liters if you have the 10.25 Ring gear. Good luck and hope this helps.

Jul 07, 2009 | 1998 Ford F150 Regular Cab

1 Answer

1993 ford f150 5 liter manual trany 4x4


if there is a clip holding the speedo cable into the speed sensor--remove clip--pull & twist---or remove the 10 mm bolt & remove the speed sensor

Jun 27, 2008 | 1993 Ford F150 SuperCab

Not finding what you are looking for?
1998 Ford F150 Regular Cab Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...