Question about 1982 Chevrolet G20

Open Question

Steering gear box on a 1983 chevy sports van

How do get the play out of steering gear box because it wants to stick when i make a turn?whick way do i need to turn the screw ?

Posted by on

5 Suggested Answers

chiquititas
  • 1010 Answers

SOURCE: 1987 Chevy G20 van replace power steering pump

Does your van have the serpentine belt? If so maybe I can help, I replaced the Power steering pump on my 90 G20 a couple of weeks ago. The trick is that you need to pull the pump pulley which is pressed on to access the mounting bolts which attach the pump to the engine. Harbor Freight tools sells a great tool designed for this job for $20.00. Once you have the correct tools, remove the serpentine drive belt. You may also need to remove the fan shroud. the pump shaft looks like it has an allen socket in the center, but this is for use in the manufacturing process, and will not come out. Place the puller tool on the pulley following tthe instruction that come with the tool, and remove the pulley. loosen, but do not remove the nut on the high pressure hose connection. use a pair of **** pliers to cut and remove the crimp clamp on the low pressure hose. If your pump has the remote reservour loosen the clamp on the reservour hose also. Remove the three mounting bolts, place a large pan under the pump to catch drips, and remove the prevously loosened hoses. there will be fluid leaking all over and the pump should come free, There are two types of replacement pump sold. With and without reservour. This reservour is a metal cover that fits over the back of the pump, and should not be confused with the reomte revervour found on some newer models which is next to the battery. This reservour is held in place be two throught the pump bolts which are removed at the back of the pump. If your new pump has a reservour you will probably still need to remove these bolts and put them in the replacement pump as most are shiped without these bolts. If you replacement pump comes without a reservour pull the bolts, the reservour should pull off of the old pump and slide onto the new one. check the o rings and replace the through the pump bolts. Installation is the reverse of removal execpt that 1/2" hose clamps replace the crimp clamps on the low pressure hose, and the puller tool is set up differently to replace the pulley. Finally if you don't flush contaminants out of the system your repair will last maybe a week. www.cardone.com has a great article about power steering flushing, read it before you start Good luck.

Posted on May 15, 2008

chiquititas
  • 1010 Answers

SOURCE: 1982 G30 Chevy Van power steering fluid

Find the power steering pump. The fluid goes in the top of the pump. Look for a twist off cap that has a measuring stick attached to the under side, when you take it off. Make sure you use the correct type of fuild for YOUR kind of vehicle. There are diffrent types for different makes of vehicles. Don't OVERFILL the pump.

Posted on May 15, 2008

  • 16 Answers

SOURCE: Which power steering line goes where on Chevy K1500 gear box?

if the fittings aren't different sizes to help you out, it will be the fitting furthest from the frame, closest to the rad. or engine. all gm trucks are like this.

Posted on Dec 11, 2008

alicantecoli
  • 21990 Answers

SOURCE: How do I access and replace the neutral safety

not sure about this but i think that all motors have this sort of thing in the gearbox not on the gearchange lever,but then we only have macho man manuals here in spain cant give autos away evan to the morrocan rag heads

Posted on Apr 02, 2009

  • 40 Answers

SOURCE: 89 Chevy G20 Sports Van; All power shuts

Would suspect chaffed wire insulation grounding out possibly wiring harness running under the alternator bracket.

Posted on Feb 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi experts ! I replaced the gear box on a 1995 Chevy G10 van ( my first ) and now I have more left turn than right turn . I think I have to remove the P arm ( is there a trick to that ? ) and adjust the...


yes you will have to remove the pitman arm and turn the gear box so that it turns more to the right. it has slots so align it on the next slot to the right. they make a tool that they call a pitman arm puller that raps around the pitman arm and puts pressure on gear box shaft wile turning it clock wise. you'll figure it out once you see the tool. the big nut usually takes 1 1/4 inch socket. hope this helps

Jul 08, 2010 | 1995 Chevrolet K1500

1 Answer

Can steering wheel play be adjusted at gear box in a 1984 chevy 4x4?If so, how is it done?


Yes, you'll need to loosen the nut on top of the steering box and turn the screw, to tighten, then tighten back up the nut.

Jun 02, 2010 | 1984 Chevrolet K1500

1 Answer

1977 CHEVY VAN HAS A SHORT IN IT . HAD TO REPLACE


It's free but I can't post pdf files here. Please post your email and I can send it to you.

Feb 06, 2010 | 1983 Chevrolet Chevy

1 Answer

I need a diagram of the firing order on an 81 chevy sport van with a 305 c-20


chevys firing order is 1-8-4-3-6-5-7-2- at front of engine number one cylinder is on drivers side

Jan 17, 2010 | 1983 Chevrolet Sportvan

1 Answer

How to remove and install a steering box w power in 1982 chevy van 250 engine ...will I need special tools,etc...? Hopefully with pictures of procedure...Thanx...Greg


the only special tool you'll need is a "pickle fork" to remove the pitman arm off the old gear box.
You can find this pickle fork at your local auto parts store to buy or rent.

Oct 12, 2009 | 1985 Chevrolet Chevy

1 Answer

Too much play in steering of chevy caprice 1994


Faulty pump or gear box at the worst. MOST LIKELY TIE RODS. Are you hearing a clunking when turning?

Jul 10, 2009 | 1997 Buick Riviera

2 Answers

How do I access and replace the neutral safety switch in the steering column on a 1979 chevy camper van with the 350 engine and column shift? Trying to locate a schematic of steering column with no luck....


not sure if this helps but have a read on this

page.http://www.2carpros.com/forum/1979-chevy-van-1979-chevy-van-nuetral-safety-switch-locatio-vt135072.html

Apr 02, 2009 | 1983 Chevrolet Sportvan

1 Answer

1983 coupe deville powersteering wineing


you might have just gotten your lines crossed backwards when you do a steering pump with line change out the fluid doesnt stay with the steering gear box
start vehicle after filling the pwsp.
turn wheels both directions for at least a minute with pwsp. cap off watch the fluid if lowers then its going to gear box where its required to stay the wineing is something the box does when its brand new it has to broken in like shoes propper fluid is a plus

Jun 01, 2008 | 1983 Cadillac DeVille

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

66126 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...