Question about 2001 Hyundai XG300

1 Answer

Rear power windows stay down. - 2001 Hyundai XG300

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 129 Answers

GO AND FIND ON YOUR OWNER'S MANUAL WHERE THE FUSE BOX AND THE RELATED FUSE AND /OR REAR RELAY WINDOWS IS AND REPLACE,
http://www.hyundaiusa.com/owners/myhyundai/login.aspx?ReturnUrl=%2fowners%2fservice%2fownersmanual.aspx
YOUR RATING YOUR MY ANSWER IS HIGHLY APPRECIATE
THANKS

Posted on Jul 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 gmc envoy Windows fuse


Are all windows not working ? Two separate circuit breakers left & right . Both in rear fuse box . Fuse Block - Rear Beneath the left rear seat
Check for broken wires inside the rubber boot from body to doors.
Do you know about electronic control modules ?
The power window system consists of the following components:
?€¢
Driver door module (DDM)


?€¢
Passenger door module (PDM)


?€¢
Body control module (BCM)


?€¢
LR power window switch


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left rear window)


?€¢
RT DOOR CB 25A (System power for right rear window)


The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.

Check

Oct 21, 2016 | 2003 GMC Envoy

1 Answer

Is there a fuse for the window switch


Which window switch ? RT DOOR CB-circuit breaker , do you know what a circuit breaker is ? 25A (System power for right rear window)
LT DOOR CB 25A (System power for left rear window
The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.


The power window system consists of the following components:
?€¢
Driver door module (DDM)


?€¢
Passenger door module (PDM)


?€¢
Body control module (BCM)


?€¢
LR power window switch


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left rear window)


?€¢
RT DOOR CB 25A (System power for right rear window)


If you not sure about any of this I suggest you take your vehicle to a ASE certified repair shop .

Oct 08, 2015 | 2002 Chevrolet TrailBlazer

1 Answer

Right rear window stays in power down


Motor stuck in power down mode

Apr 05, 2015 | 2003 Chevrolet Tahoe

3 Answers

My back automatic window went down and now won't come back up. No sound from motor. Checked fuses. Even took back seat apart but don't know what to do or what caused it. How can I get window to go...


it may need to be reset.

SECTION 501-11: Glass, Frames and Mechanisms 2001 Explorer Sport/Sport-Trac Workshop Manual
GENERAL PROCEDURES Rear Window Motor Initialization s1r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.
NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.
NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.
NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.
NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.
NOTE: Steps 7 and 9 require that the power rear window control switch be held in the closed position until the power rear window motor stalls the window in the upper header seal. Step 8 requires that the window control switch be momentarily turned to the open position.
  1. Start with the ignition in the OFF position.
  1. Turn the ignition to the ON position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the OFF position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the ON position. The power rear window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialized mode.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls in the upper header seal.
  1. Momentarily rotate the power rear window control switch to the open position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls into the upper header seal. Once this operation is complete, the window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.
  1. Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions.
------------------------------------------------------------------------------------
  • The power rear window is inoperative (Explorer Sport Trac only)
  • Circuitry.
  • Battery Junction Box (BJB) fuse 3 (30A).
  • Central Junction Box (CJB) fuse 20 (7.5A).
  • Power rear window control switch.
  • Rear window glass motor.
  • Go To Pinpoint Test K .

------------------------------

Sep 15, 2011 | 2001 Ford Explorer Sport Trac

1 Answer

Where is the rear window relay located on the 2002 Ford Explorer sport trac. Not the rear door windows but the very back window.


  • The power rear window is inoperative (Explorer Sport Trac only)
  • Circuitry.
  • Battery Junction Box (BJB) fuse 3 (30A).
  • Central Junction Box (CJB) fuse 20 (7.5A).
  • Power rear window control switch.
  • Rear window glass motor.

NOTE: The power rear window motor is not on the multiplex link. Any diagnosis and testing carried out on the power rear window will not involve the GEM module. NOTE: The reinitialization procedure must be carried out when repairs are performed on any part of the power rear window system including when the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.

Rear Window Motor Initialization s1r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.
NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.
NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.
NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.
NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.
NOTE: Steps 7 and 9 require that the power rear window control switch be held in the closed position until the power rear window motor stalls the window in the upper header seal. Step 8 requires that the window control switch be momentarily turned to the open position.
  1. Start with the ignition in the OFF position.
  1. Turn the ignition to the ON position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the OFF position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the ON position. The power rear window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialized mode.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls in the upper header seal.
  1. Momentarily rotate the power rear window control switch to the open position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls into the upper header seal. Once this operation is complete, the window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.
  1. Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions
---------------------------------------------------------------------------------------------

Nov 16, 2010 | 2001 Ford Explorer Sport Trac

1 Answer

The rear window went down a couple of inches and wont stay up


you will need a window regulator, its not cheap.

Mar 12, 2010 | 2004 Pontiac Grand Prix

2 Answers

2000 Freelander-window stuck in down after cable replace


Firstly check the wiring then motor is only working one way that means that the power is not being reversed to put it back up, switch the wires around from the switch if it go's back up then you know there is a wiring fault.

hope this helps
Regards
Dan

Feb 04, 2010 | 2003 Land Rover Freelander

2 Answers

Replaced battery on freelander rear window will not stay up carried out procedure in manual but window goes up beeps and goes down.no problem at all untill battery replaced.


disconnect battery reconect after 5 mins on reconnection rear window will go down , use key in rear lock to reset rear window, door lock should now work, if not try rear door relays behind left hand rear panel.

Jun 13, 2009 | 2002 Land Rover Freelander

1 Answer

Car windows rear


this car has a cable regulated window,check to see if guide for cable is not worn or broken.These regulators tend to be very expensive.Look at junk yard .

Oct 02, 2008 | 1990 Nissan Maxima

Not finding what you are looking for?
2001 Hyundai XG300 Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...