Question about Mitsubishi Lancer Evolution

1 Answer

Mitsuibishi lancer evo 4

Changed clutch now when i start the car it wont go in to gear if i hold the clutch peddle down then start it, it will go in to gear can u help me please

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 126 Answers

Im a little confused re clutch replacement normally in order to start a manual transmission car the clutch pedal needs to be pressed down all the way before the car will turnover . as you say it will start but you need to push down clutch am i right? but when you try to put it into gear grinding ?wont go in to gear yes is this whats hapinin?ok the way that these clutches work nowadays is that there is a system similar to brake system there is a resivoir for the oil and a slave cylinder that pushes the clutch throwout leaver so that the gears can be changed did you see a small cylinder that pushes against the clutch lever? does it have a hose coming from it ? this system needs to be bleed just like the brakes on your car . find the resivoir small resivoir open lid and fill with brake fluid now go under car and find slave cylinder it will be somewhere near the transmission and bellhousing there will be a hose attached there will also be a bleed nipple attached you need to open this a few turns and let it drip dont press clutch pedal when bleed screw is open it will bring air into system , you want to remove all the air in the system so get a friend to go into car and pump clutch pedal then hold it to the floor while its being held down you open bleed screw until clutch pedal hits the floor tighten bleed screw then tell friend to pump up again do this 5 or 6 times making shure clutch fluid level doesnt drop down too far keep topping it up with the fluid that squirts out while bleeding this way you dont waste fluid as well as keeping fluid from hitting the ground .anyhow after trying this slave cylinder bleeding proceedure .try to see if car will go into gear . also see that there is no adjustment on slave cylinder . also i hope that you put the clutch facing the correct direction flywheel side towards flywheel . let me know how you do with this project

Posted on Jul 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HI. The clutch peddle on my citroen C4 1.6 HDI stays on the floorboard when pushed please help.


Check this forum:
http://www.citroenpicasso.org.uk/picasso/index.php/topic/18177-sticking-clutch-pedal/

Sep 21, 2016 | Citroen Cars & Trucks

1 Answer

What is the problem when i push the clutch in and it wont release the fly wheel and the truck wants to jump forward when i started it in first gear and i have clutch pedel pushed in


of you have just replaced the clutch ,the clutch plate is in back to front and the hub is hitting on the flywheel bolts
If you haven't done that then there is air in the system and the clutch is not disengaging

Mar 07, 2015 | 1998 Isuzu Hombre

1 Answer

Loud snapping noise heard when changing gears


From the way you've described it your gear stick linkages maybe on there way out. When changing gear does the car resist getting into gear?

If it's more of a crunching sound then I would try double de clutching, to do this you need to:
change gear as usual but instead of holding down the clutch throughout the gear change hold it down to take the vehicle into neutral then release the clutch then push the clutch down again and change into desired gear.
To change down it's basically the same principal but you push down the clutch to put the vehicle into neutral then push the throttle down just to pitch revs then release the throttle and push the clutch down to change into your desired gear, if it won't go in to gear easily then rather the throttle until it does.

You can go onto youtube and search for double de clutching and I'm sure some results will come up

hope this helps!

Apr 30, 2014 | 2004 Nissan Altima

1 Answer

2008 mitsuibishi lancer es - trying to locate and change my cigarette lighter fuse. Where do I locate it and how do I identify it?


First place to look is the owner's manual. Should be a roadside emergency chapter in it with a list of fuses and usually a schematic to locate it. If worse comes to worse a local AutoZone or Advance Auto store will generally change the fuse for you if you are uncomfortable with the process.

Apr 25, 2012 | 2008 Mitsubishi Lancer GTS CVT Sedan

1 Answer

Theres a problem changing gears, its a soft very low biting clutch peddle, unable to change down from high ratio gears to low ratio gears, having to knock into nuetral pump the clutch to select gears...


This sounds like you may have a leak in the hydrulics of the clutch, the clutch slave is not disengaging the clutch all the way, this is the reason for the low bite pedal and hard to get gears, the most common problem is the fluid is low due to a leaking slave cylinder, i would look around the clutch components for a leak, hope this helps.

Oct 27, 2010 | 2007 Hyundai Tucson Limited

1 Answer

Automatic 330i 2001, if i start accelarating at 3rd gear the RPM keep increaing and if i release the gas the car should change to next gear but i does not...at low RPMs it is working fine


the gearbox is a "fuzzy logic"system.gearchange depends on accelerator pedal position/revs/load.if you drive without depressing the gas peddle more than a third down you should find all gearchanges much smoother.(if you drive with gas peddle almost hard down all the time yhe car will hold gears longer...poss 4500 revs or more......

Feb 23, 2010 | 2001 BMW 330

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

580 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...