Question about 2001 Saab 9-3

1 Answer

2001 Saab 9-5 Power Door Lock problem

Power door locks stopped working when using the key. Button on the center console does lock and unlock the doors. I replaced the battery in my key... still doesn't work. Any ideas? Perhaps a fuse?

Posted by on

  • 5 more comments 
  • Anonymous Mar 13, 2009

    2001 9-5 3.0 liter se wagon. Electric lock system will not function fron either the inside button control, or the remote key-fob control. Doors must be manually locked/unlocked

  • mhivon May 06, 2009

    trunk work, doors no, alarm system work well with remote

  • Anonymous Mar 14, 2014

    We went outside to grab something from our 2011 Mitsubishi Outlander and the battery is dead. We used the emergency key, but the doors will not unlock. Is there any other way to get in??

  • Anonymous Mar 18, 2014

    2004 model- cant unlock passenger dor at front, door locked closed

  • Anonymous Mar 27, 2014

    2006 model. Use 20A fuse had already changed more than 10 fuses during the last 3 months.. Please advise. Thank you. Leon Lee

  • Anonymous Mar 27, 2014

    Changed more than 10 20A fuses in 3 months. Problem not solve can someone please help. Leon

  • Anonymous Mar 30, 2014

    My power door locks stop working there no fuse

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Does the key still pop the trunk/hatch? That would also indicate whether or not it was the key remote. If that function works it's probably nothing on the car (i.e. "receiver") end.

There is a very good SAAB forum that would likely be the best place to find out if somebody has has this issue before and what they have done: www.saabcentral.com

Posted on Jul 21, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2011 Ford Fiesta 5 speed manual base model no key fob ONLY drivers side door lock w key. Mechanism in drivers side door lock not catching not working will not lock or unlock. Electronics inside at console...


LOCKING AND UNLOCKING
You can use the power door lock control or the remote control to lock and unlock your doors and tailgate.See Tailgate Lock.
Power Door Locks
The power door lock control is on the driver and front passenger door panels.

AUnlock.
BLock. Remote Control
You can use the remote control at any time your vehicle is not running.
Unlocking the Vehicle (Two-Stage Unlock)
Press the button to unlock the driver door. Press the button again within three seconds to unlock all doors.The direction indicators flash. The direction indicators flash twice to confirm the change. The unlocking mode applies to the remote control, keyless entry keypad and intelligent access.
Press and hold both the lock and unlock buttons on the remote control for four seconds to disable or enable two-stage unlocking. Disabling two-stage unlocking allows your entire vehicle to unlock with one press of the button.
Intelligent access at the driver door unlocks your entire vehicle when you disable two-stage unlocking.
Locking the Vehicle
Press the button to lock all doors.The direction indicators flash.
Press the button again within three seconds to confirm that all the doors are closed.The doors lock again, the horn sounds and the direction indicators flash if all the doors are closed.
Mislock
If any door is open, or if the hood is open on vehicles with an anti-theft alarm or remote start, the horn sounds twice and the direction indicators do not flash.
Activating Intelligent Access
General Information
You can unlock and lock the vehicle without taking the keys out of your pocket or purse when your intelligent access key is within 3 ft (1 m) of your vehicle. Intelligent access uses a sensor on the back of the door handle for unlocking and a separate sensor on the face of each door handle for locking.
The system does not function if:
  • Your vehicle battery has no charge.
  • The key battery has no charge.
  • The key frequencies are jammed.
Note: The system may not function if the key is close to metal objects or electronic devices, for example keys or a cell phone.
Note: If the system does not function, use the key blade to lock and unlock your vehicle. See Remote Control.
Unlocking Using Intelligent Access
With your intelligent access key within 3 ft (1 m) of your vehicle, touch the unlock sensor on the back of the door handle for a brief period and then pull on the door handle to unlock, being careful to not touch the lock sensor at the same time or pulling the door handle too quickly. The intelligent access system requires a brief delay to authenticate your intelligent access key fob.
Locking Using Intelligent Access
With your intelligent access key within 3 ft (1 m) of your vehicle, touch the outer door handle lock sensor for approximately one second to lock, being careful to not touch the unlock sensor on the back of the door handle at the same time. After locking, you can immediately pull on the door handle to confirm locking occurred without inadvertently unlocking.
Note: Do not use the outside door handle as a roof cargo strap.
At the Electronic Tailgate (If Equipped)
Press the exterior tailgate release button inside of the tailgate handle. The tailgate unlocks and opens. See Electronic Tailgate.
Smart Unlock
This feature helps to prevent you from locking your intelligent access key inside your vehicle's passenger compartment or rear cargo area.
If you leave your key in the ignition, when you open the driver door and lock your vehicle with the power door lock control, the doors lock then unlock.
You can still lock your vehicle with the key in the ignition by:
  • Using the manual lock on the inside of the door.
  • Locking the driver door with a key.
  • Using the keyless entry keypad.
  • Using the lock button on the remote control.
Smart Unlocks for Intelligent Access Keys
This feature helps to prevent you from locking your intelligent access key inside your vehicle's passenger compartment or rear cargo area.
When you lock your vehicle using the power door lock control (with the door open, vehicle in park and ignition off), your vehicle searches for an intelligent access key in the passenger compartment after you close the door. If your vehicle finds a key, all of the doors immediately unlock.
In order to override the smart unlock feature and intentionally lock the intelligent access key inside your vehicle, you can lock your vehicle after all doors are closed by using the keyless entry keypad, pressing the lock button on another intelligent access key or touching the locking area on the handle with another intelligent access key in your hand.
When you open one of the front doors and lock your vehicle using the power door lock control, all doors lock then unlock if the ignition is on.
Autolock
Autolock locks all the doors when:
  • All doors are closed.
  • The ignition is on.
  • You shift into any gear putting your vehicle in motion.
  • Your vehicle reaches a speed greater than 12 mph (20 km/h).
Autolock repeats when:
  • You open then close any door while the ignition is on and your vehicle speed is 9 mph (15 km/h) or lower.
  • Your vehicle reaches a speed greater than 12 mph (20 km/h).
Autounlock
Autounlock unlocks all the doors when:
  • The ignition is on, all the doors are closed, and your vehicle has been moving at a speed greater than 12 mph (20 km/h).
  • Your vehicle comes to a stop and you switch the ignition off or to the accessory position.
  • You open the driver door within 10 minutes of switching the ignition off or to accessory.
Note: The doors do not autounlock if you electronically lock your vehicle after you switch the ignition off and before you open the driver door.
Enabling or Disabling Autounlock
You can enable or disable the autounlock feature in the information display or an authorized dealer can do it for you. See General Information.
Illuminated Entry
The interior lamps and select exterior lamps illuminate when you unlock the doors with the remote entry system.
The illuminated entry system turns off the lights if:
  • The ignition is on.
  • You press the remote control lock button.
  • After 25 seconds of illumination.
The dome lamp does not turn on if the control is set to the off position.
The lights do not turn off if:
  • You switch them on with the dimmer control.
  • Any door is open.
Battery Saver
The battery saver turns off the interior lamps 30 minutes after you switch off the ignition if a door is open and the dome lamp switch is on. It turns off the interior lamps after 10 minutes if the dome lamp switch is off.
Accessory Mode Battery Saver for Intelligent Access Keys (If Equipped)
If you leave the ignition on after leaving your vehicle, it turns off 15 minutes after you close all of the doors.

Mar 27, 2018 | Ford Cars & Trucks

1 Answer

How do i synz my keys to my 2000 renault clio


Climb in vehicle close door press and hold central lock button on console. Doors lock and unlock. Release lock button press and hold button on key for a few seconds doors should lock

Jun 12, 2014 | 2002 Renault Clio

4 Answers

2003 330XI keyless entry. wont open or close.


The transponder is not effective any longer sometimes the battery of the remote is very low which needs to be replaced

Jan 17, 2018 | BMW 330xi Cars & Trucks

1 Answer

Sorry my car was not listed so picked Altima 2003 Micra Intelligent key fob not working properly. Can drive the car but cannot open or lock the doors. Did get fob wet. Now dried out. Worked for first few...


You are going to need to check the power lock control moduel on the inside of the door panel. If the FOB appears to be working but the doors are not unlocking, you need to check this. I would also replace all fuses that control the locks. If both of these devices check out ok, you may need to replace your FOB. To check your power lock control moduel, manually lock and unlock your doors by pressing the lock button on the inside of the door. If it does not work, it is either the fuses or the power lock control moduel. If it works, your FOB has gone bad. Hope this helps! Please rate 4 thumbs up!

Apr 18, 2011 | Nissan Altima Cars & Trucks

1 Answer

Hello there top of the morning to you! First of all I just bought a 2000 Audi TT 1.8T yesterday and didn't realize a few things till i brought her home from the dealer. The key fob needed new batteries so...


once you fitted new batteries to both fobs you needed to reset the car.....put key in drivers door and unlock/hold key over(windows go down)wait 30 secs then lock/hold over key,(windows go up)wait 30 secs,then press/hold unlock button for 30 secs.you have just reset the system.you have loads of other little gizmos but i will leave you to find them all good hunting....one side parking lights/driveway illumination/and more.
geoff

Sep 10, 2010 | Audi TT Cars & Trucks

1 Answer

After battery replacement keyless entry stop working


Synchronization
When
Key buttons operated repeatedly while vehicle out of range and system becomes inoperative. Key batteries replaced.
How - early models
Depress lock or unlock button. Manually lock and unlock driver's door within 30 seconds. System should operate normally after approximately 1 minute. If not, carry out programming procedure.
How - late models
If vehicle locked, manually unlock driver's door using key. Press key unlock button once. Switch ignition ON and OFF. Remove key from ignition switch. Press key lock or unlock button once. System should now operate correctly.

Jun 24, 2010 | 2007 Audi A4 Convertible

1 Answer

My power door locks stopped working. When I press


The locks don't work from any switch or just the driver's door switch ? The door locks are controlled by the BCM - body control module , that's were the clicking you hear is coming from there are no fuse's that are marked for the locks , fuse's for the BCM .

Door Lock System Components
The power door lock system consists of the following components:
• Driver door lock switch -- Uses a single signal wire for both lock and unlock switch activations
• Front passenger door lock switch -- Uses a single signal wire for both lock and unlock switch activations
• BCM -- Class 2 module which requires programming when replaced
• Reversible door lock actuators in each of the doors
• BCM PWR 15A fuse -- Located in the BCM fuse panel, supplies power for the door lock system

The BCM PWR fuse supplies battery positive voltage to the BCM for the door lock system.
The BCM supplies and monitors a reference voltage to the door lock switch through the door lock switch lock/unlock signal circuit. The door lock switch also receives a constant ground source. If a door lock switch is placed in the lock position, the reference voltage is taken directly to ground and the BCM senses 0.0 volts on the signal circuit. If a door lock switch is placed in the unlock position, the reference voltage is taken to ground through a 15k ohm resister that is internal to the door lock switches and senses approximately 2.9 volts on the signal circuit. This is how the BCM determines what portion of the door lock switch was activated.
The BCM, upon receipt of a door lock switch lock or unlock signal, will switch the appropriate door lock actuator control circuits to battery positive voltage. The opposing side of the door lock actuators are connected to ground internally within the BCM through the other door lock actuator control circuit and the doors will lock or unlock appropriately.
Vehicles without keyless entry have two internal drivers in the BCM to control the door lock actuators. All door lock and all door unlock. Vehicles equipped with keyless entry have three internal drivers in the BCM. Driver door unlock, passenger door unlock and all door lock. This is done to isolate the driver door lock actuator so it can be unlocked by itself using the keyless entry transmitter.

Body Control Module (BCM)
Lower center of the I/P, just below the HVAC control assembly

Mar 04, 2018 | 2004 Saturn ION

1 Answer

I unhooked the battery now i cant stop the horn and it wont start the remote key does not work it got washed in clothes help please.97 camry


Lock then unlock the doors with the power lock button, with all doors closed (key not in ignition). If this doesnt work, try again using the key to lock and unlock from the driver door, with all doors closed.

May 12, 2010 | 1996 Toyota Camry

3 Answers

The Lexus car remote key control model ES300


try this:

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (DO NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes.

Mar 23, 2009 | 1997 Lexus ES 300

3 Answers

Program remote control for mazda mpv 2002


Courtesy of: forums.mazdaworld.org

Try this, it works on several 2002 models:


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the drivers door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the drivers door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done

Dec 06, 2008 | 2000 Mazda MPV

Not finding what you are looking for?

Open Questions:

See all 2001 Saab 9-3 Questions

2001 Saab 9-3 Logo

1,870 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

79865 Answers

derek oliveira

Level 2 Expert

85 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...