Question about 2000 Dodge Intrepid

1 Answer

Tie rods how do i relaceplace an inner tie rod on a 2000 dodge intrepid

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 1,463 Answers

I did this on a 2002 Intrepid, and found that it wasn't too complicated. I replaced the bushings only, rather than the tie rod end. You can get bushing replacement kits where the bushing is in two pieces and doesn't have to be pressed in. Before starting, turn the steering all the way to the right, then remove the intake air ducting. The rack and pinion assembly should be easily accessible now. BE SURE AND REPLACE ONLY ONE TIE ROD BUSHING AT A TIME. If you take both bolts out at the same time, you may have a very hard time getting all the sleeves, etc. aligned in the steering unit so you can get the bolt back in the proper hole.

Posted on Dec 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I also have a 1995 Dodge Intrepid with bad tie rods; I have purchased the parts, but I am having trouble removing the INNER tie rods. There is something preventing me from putting a wrench on the bolt


There is a special tool to remove inner tie rod. You usually can rent this from a Autozone parts store. When you return the tool, they give you back 100% your money as long as you don't damage the tool.
It consists of a long pipe with a open end wrench at the end.

Aug 16, 2014 | 1995 Dodge Intrepid

1 Answer

2000 Dodge Grand caravan Inner tie rod end


use a pipe wrench also known as a monkey wrench that will work just make sure there is not a lock screw keeping it from turning some aftermarket inner tierods have alittle allen head screw to keep them from turning

Aug 27, 2012 | 2000 Dodge Grand Caravan

1 Answer

Slack in steering wheel


These may have problems with the Inner Tie Rod Bushings. The inner tie rods are up on the firewall behind the engine, have someone turn the steering wheel back and forth (just enough to feel all the play) and see if the rods are loose.

Sep 02, 2010 | 2002 Dodge Intrepid

1 Answer

How to repaire inner tie rod bushings


you need to get it out.
get on the engine and go to the back at the fire wall
look for the bolt that hold the tie rod
there should be a lock washer which is bent to keep the bolt in place
bend down the tab so you can put a wrench on the bolt
loose the bolt then loose the outter tie rod
take the rod out and repair or replace

Mar 04, 2010 | 1999 Dodge Intrepid

2 Answers

2000 LINCOLN LS - Outer tie rod removal assistance


Yes degreaser will not hurt it. The outer tie rod is retained only by one nut that connects it to the inner tie rod.Once you have this loosen just turn the outer tie rod to the left to remove it from the inner tie rod.

Feb 24, 2010 | 2000 Lincoln LS

2 Answers

Tie rod


No. Go to Napa, get the bushing repair kit. Turn the steering wheel all the way to the right. Remove the air inlet tube. Should be 2 7/8" bolts retaining the inner tie rod ends. Loosen both. Remove one at a time, replace bushing with kit. Use some synthetic brake grease on the bushings. I recommend Napa sylglide. Replace the bolt, but do not tighten all the way. Do the other the same way. Tightnen both bolts, reinstall the air inlet tube, get vehicle aligned.

Jul 22, 2009 | 2002 Dodge Intrepid

1 Answer

1996 chrysler concorde, how to take off the inner tie rod?


I used this website: http://www.allpar.com/fix/intrepid-steering.html It worked perfectly. To add to it, I used a tie rod puller tool rented from Oreilly Auto Parts for only a few bucks, to press the old bushing out of the inner-tie-rod end. Worked very well. Easier than removing the entire tie rod, and hammering it out. However, removing the entire tie rod would make re-assembly easier. If I did it again, I would strongly consider removing the driver side tie rod from the car, then attaching the inner tie rod end 1st. Meaning, attach the passenger side inner tie rod 1st, then the driver side inner tie rod with new bushing, then re-attach the drivers side outer tie rod. That would probably be the easiest way on this 1996 dodge concorde, due to the fuel line that's in the way....

Mar 17, 2009 | 1996 Chrysler Concorde

1 Answer

2001 Intrepid, is the tie rod end located above the wheel and is it a threaded assembly?


the tie rod end is at the wheel their is an outer and a inner they are both threaded

Mar 08, 2009 | 2001 Dodge Intrepid

2 Answers

1997 dodge Intrepid: inner tie rod


To Steering Gear Bolt 90 Nm (66 ft. lbs.) Jam Nut 75 Nm (55 ft. lbs.)
NUMBER: 19-001-01
GROUP: Steering
DATE: Mar. 23, 2001
THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 19-003-00 REV A, DATED OCTOBER 6, 2000 WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND INCLUDE PART NUMBER CHANGES AND ADDITIONAL MODEL YEAR.
WARNING: FAILURE TO ACHIEVE A MINIMUM TORQUE OF 100 NM (74 FT. LBS.) MAY RESULT IN THE ATTACHING BOLTS LOOSENING AND FRACTURING. THIS COULD RESULT IN A SUBSEQUENT LOSS OF STEERING CONTROL. BENDING THE RETAINING TABS ALONE WILL NOT PREVENT THIS.

SUBJECT:
Loose Steering

OVERVIEW:
This bulletin provides service procedures and parts information for the inner tie rod bushings.
MODELS:
1993 - **2001 ** (LH) Concorde/Intrepid/LHS/New Yorker/Vision/300M
SYMPTOM/CONDITION:
Loose feel or clunk in the steering wheel as the wheel is moved from side to side.
DIAGNOSIS:
Observe the inner tie rod to steering gear attaching point while moving the steering wheel from side to side. If there is movement between the gear and inner tie rod, perform the Repair Procedure. If no movement is evident further diagnosis of the condition will be required.
DISCUSSION:
The inner tie rod bushings have previously been serviced with the tie rod assembly. This bulletin releases the parts, service procedures, and special tool necessary to service just the bushings. Subsequent service manuals will contain the Repair Procedure.

Jan 13, 2009 | 1994 Dodge Intrepid

2 Answers

Replacing outer tie rod on a 2000 dodge neon


put the tie rod back in and thread the nut on. then you turn the inner tierod with a pipe wrench or a big pair of channel locks. you can spray the threads with pb blaster or wd-40. also if ya have a propane torch this helps loosen the threads. apply heat to the outer tierod do not heat the inner. good luck jimmy

Oct 03, 2008 | 2000 Dodge Neon

Not finding what you are looking for?
2000 Dodge Intrepid Logo

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...