Question about 1997 Jeep Wrangler

1 Answer

Wiring There are two electrical lines under driver seat with terminals that look like they should be connected. Should I plug them in or let them apart. It's a 97 wrangler rag top, 4 cyl.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 362 Answers

If they are not the same color leave them alone if the same color plug them in

Posted on Jul 03, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

"Have 4 wire hanging from under the driver side blue, red not sure what they go to?

The red is either the positive terminal for controlling the seat whichever way and other wire would be the negative. If you have electric seats it could be that at any rate write down the cars options and those wires will be the control wires or pover wires. You can take a needle and pierce the insulation so it makes contact with the wire. Now connect a multimeter to them + to + and - to -. Now, watch the meter and see if the numbers vary when you move the seat, change a seat control like heat whatever you wrote down ads options. That will tell you exactly what the wired control. Make sure the meter is set to reading dc voltage and not ac or ohms.

Nov 07, 2014 | Cars & Trucks

1 Answer

I have a 99 accord the alternator plug was cut. Looks like they tried to splic the wires to fit a different plug or something. What wires do I run to each metal piece on the alternator?

The WHT/RED wire from the PCM connects to terminal 4 (FR); the WHT/GRN wire from the PCM connects to terminal 2 (C); The BLK (or WHT) wire from the underhood fuse/relay box connects to terminal T102 (B); the WHT/BLU wire from the gauge assembly connects to terminal 3 (L), and the BLK/YEL wire from the driver's under-dash fuse relay box connects to terminal 1 (IG)

Oct 09, 2014 | Cars & Trucks

1 Answer

My driver's side power seat quit working. The memory module and switch on the seat work OK but the voltage through the seat switch is very low, about 2.0Volts. When I ground the switch to the chassis it...

Check G-302 for lose connection.
Under the right front seat, on the number 2 bar near the inflatable restraint sensing diagnostic module

Terminal L driver seat switch connector . Black wire is ground to G-302 .Test by loading the circuit

Oct 14, 2017 | 2005 Cadillac Deville

2 Answers

The Airbag light blinks 4 times ... pauses ... then repeats ... This is intermitent ...

Those are Lamp Fault Codes,they also go with
Diagnostic Trouble Codes

Solution---you can not diagnose that SRS System,
you will need Professional Help

Scanner and a Trouble Chart

Feb 17, 2011 | Ford Contour Cars & Trucks

1 Answer

2001 ford focus airbag light blinks 4 times then stops, then starts again.

disconect the battery
locate the airbag wires under the seat
unplug it on both drivers and passanger seat
spray some brake cleaner or de greaser in to the terminals and blow out with air line
re connect plug connectors
re connect battery
if this doesnt work then you will need subtable diagnostics equipment to read the faults on the airbag system

please let me know if this helps you out
big mike :)

Jan 04, 2010 | 2004 Ford E150

1 Answer

Where do i check gear boox fluid and top up . drivers heated seat stoped working

Manual transmission fluid level is checked through a fill plug on the side of the transmission. THe fluid should be level with the bottom of the hole. Automatic transmission fluid is checked via a dipstick under the hood. Your owners manual should have detailed instructions for checking both.
For the seat heater, check the fuses, then the electrical connectors and wire connections under the seat.

Dec 30, 2009 | 2002 Jeep Grand Cherokee

2 Answers

1999 Cadillac Deville Driver side power seat not working

No fuse.These seats are protected with relays and a seat module.The module is under the drivers seat.There are 3 connectors and it would be hard to check all these wires for power to the motors.First look under the seat and make sure none of the connectors came apart under the seat by something that might have been left or rolled under it.The 2 main ones you can check are the connector 2 terminal C and connector 3 terminal A.C is a black wire which is ground and A is a red wire which is the feed power wire.Connector 2 is green and 3 is black.If the ground and power wires are good then you could have a bad drivers seat module.What I would do is go to the salvage yard and find a used module to try.Good luck.

Dec 07, 2009 | 1999 Cadillac DeVille

1 Answer

Power seat wont work

Big problem with these cars is the electrical connector behind the driver seat on the floor. Son of a gun to open use a small screw driver and be careful. They must closetightly and hold. 90% of time the terminals are loaded with corrosion. Remove battery power from the vehicle and either clean them or replace them. If that doesn't work pull seat cushions out and test the switch. Use shop manual for this
simple test. Either check the switch for resistance or remove the switch from the electrical connectors and jump the terminals with a jumper wire to see if you get the seat motor to move. If it does you need a new switch if it doesn't you need a new motor. Shop manual may have another way to test this with the switch in place. Here you are measuing for continuity.
This is fun stuff . good luck &keep me posted

Apr 19, 2009 | 1981 Chevrolet Corvette

2 Answers

Seat belt indicator won't stop buzzing

have you tried unplugging the 2 prong plug under the seat(its right under the seat belt buckle)? i have a 98 mitsubishi eclipse and i simply unplugged it and it disabled the buzzer. if that doesn't work, you can connect the 2 wires (on the harness side) either by bridging the 2 terminals with a jumper wire or you can cut the plug off and just twist the 2 wires together.

Oct 15, 2008 | 1998 Mitsubishi 3000GT

Not finding what you are looking for?
1997 Jeep Wrangler Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

77939 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides