Question about 2004 Nissan Sentra

1 Answer

Belt snapped looking for a picture where the pulleys are so i can see how to put this belt on. Its the one for the alternator.The other belt is still there and operational. I need to see how to take the other belt off to put the new one on. Also is there a tension pully there? If there is;is it supposed to be in a fixed position when there is no belt there? That's why i need to see a picture of it. Unless you can tell me.

Posted by on

  • superhotchic Aug 02, 2008

    I need to change the larger of the belts because it is broken and i can not find a diagram on the car that can show me how to change it so how do i do it.

  • b21849 Sep 22, 2008

    I have the same problem with my belt on my 2004 Niisan Sentra breaking and not knowing, without a picture, how to replace it.

×

1 Answer

U dont need no diagram or picture to change the belt just look how your old one is on there and change the belt by unscrewing the alternator bolts and push the alternator down and take the belt off.

Posted on Nov 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does belt to alternator keep skeaking + snapping?


Bad bearings can usually be detected simply by turning the unloaded pulley (wheel). They feel sort of gritty compared to a good bearing. The squealing and snapping is a concern, however. My best guess would be a belt tensioning issue. Squealing is usually caused by belt slippage due to an unusually loose belt. This leads to belt damage and eventually, breakage. Of course a bad idler pulley bearing or other defective component (A/C, P/S, Alt) can cause the same results.

Jan 25, 2016 | 2002 Mazda Protege

3 Answers

My h2, 2004 suddenly overheated very rapidly, only two days after being serviced. The air conditioning made a high pitched squeaking sound minutes before this happened. Engine then shut down and coolant...


Sounds like the ac compressor locked up and the belt snapped from rubbing on it. Once the belt snaps, the water pump stops and the engine overhears.

Mar 06, 2011 | 2004 Hummer H2

1 Answer

Have a rebuilt 6.2 chev diesel. broke alternator belt. got new belt and put it on lower pulley, fan pulley and alternator. it keeps throwing the belt when revving the engine up. tried ac pulley, fan pulley...


It sounds like the alternator is not properly lined up. You had the belt on right the first time. Put it back on and before you start the truck check the alignment on the belt. From the side of the truck look down thw belt to the fan pulley and see if you notice a slight bend, or use a straight edge to do the same thing. Also sight down the belt to the crank for the same thing. Yoiu may have to shim out the alternator brackets to get the belt in line with the other pulleys. Hope this helps.

Oct 17, 2010 | 1988 Chevrolet G30

1 Answer

The pulley for the alternator belt broke and snapped the belt as well, now the car will not even start. what needs to be done and what are the estimated costs associated with the repairs


A belt is usually $15, and a pulley around $50.
If this has separate belts (not a serpentine) usually the belt goes around the alternator and off the main flywheel and there isn't and idler pulley - but I dont' know about TL's.
Basically you loop the belts over the pulleys. Something has to move to allow you to adjust the tension. Usually there is bolt on the alternator that is in a slot, so you move the alternator towards the flywheel to put the belt on, and away to tighten it up (you want a little deflection, but if it is too loose it will squeal - which is better than over-tightening).

Feb 24, 2010 | 1998 Acura TL

1 Answer

My 97 miata has been having terrible squeaking noises coming from alternator belt area. put new belt on and still squealed then snapped off!!! Put another new one on less tight and the pulley for the...


The alternator is loading up too much for some reason.
Had the same issue on my friend's 2001 Mazda Protege. Turned out the voltage regulator in the alternator was faulty. Had the alternator rebuilt. A week later, it acted up again! There is apparently another issue, but I have not been able to figure it out.
Unfortunately, I don't have a clear answer for you, but, one's thing's for sure. Mazda has to stop using crappy Ford electrics in their cars.

Oct 07, 2009 | 1997 Mazda MX-5 Miata

2 Answers

I have a 1986 Olds Cutlass Ciera with a 2.5l 4


Remove the belt from any pulley. Go from pulley to pulley and make sure they are all free wheeling obviously you won't be able to turn the crank pulley. Spin your alternator pulley and listen to it. It should be silent and smoothe. If you hear any bearing noise from the tensioner, the alternator, the AC comppresor, I would do this soon, you've spent on belts what an alternator would cost.Also check the idler pulley if this is a serpentine type belt.

Aug 21, 2009 | 1986 Oldsmobile Ciera

1 Answer

Belt came off 1998 chrysler sebring lxi


you have two belts . put the large belt on first . it goes around crank pulley air conditioning pulley alternator pulley.loosen tension pulley to adjust belt. tension. then you put the other belt on power steering pump pulley and crank pulley. adjust belt tension loosen power steering pivot bolt. that it.

Mar 16, 2009 | 1998 Chrysler Sebring

1 Answer

My car is a VW golf Gti mk3 8v 2.0L, Alternator / water pump drive belt has snapped and been lost. I have new belt but I'm unsure of routing around the 3 pulleys. does the alternator act as the tensioner??


loosen the alternator and push the alternator to-wards the engine,put your new belt on ,fitting around the 3 pulleys once fitted look and see that the belt is in line.If your happy the belt is lined put a small bar between the engine and alternator and force the alternator out towards the front this should tension your belt tighten bolts on alternator.;at the longest point between two pullys in the middle of the belt move belt up and down with fingers if tension is right it should not move more than about 150ml,hope this helps you.adrian

Feb 02, 2009 | 1997 Volkswagen Golf

1 Answer

Belt replaement


Sorry, with or without power steering ? Have look at this link.Scroll down to find yours, then click on picture to expand/explode for better view if needed. If it's got the idler pulley, you'll have to get a wrench on it and relieve tension, while putting belt back on. Careful, make sure wrench is all way on bolt.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152801afa93

Jan 04, 2009 | 2005 Nissan Sentra

Not finding what you are looking for?
2004 Nissan Sentra Logo

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...