Question about 1991 Chrysler New Yorker

1 Answer

91 new yorker wipers stop while using during storm

Wipers just stoped working while using and are in verticle position

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Go to your wipper motor under the shroud infront of wind shield and look for a metal plate at the botom there is a bolt threw it clean it up on both sides that is your ground.

Posted on Feb 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1991 Chrysler New Yorker dies at stops.


Check fuel pressure and see if the pump is good

Mar 05, 2013 | 1991 Chrysler New Yorker

1 Answer

Windshield wipers stop working


At the base of the wiper arm there is a plastic cap,pop this off ,underneath there is a nut that holds the arm in place ,if it gets loose the post will turn inside the blade.Just turn the wipers off and tighten the nuts with the blade in the parked position.

Jan 23, 2012 | 2003 Chevrolet Impala

1 Answer

What r the trouble codes for a 91 chrysler new yorker, 11,12,13.14 ?


11 Timing belt skipped 1 tooth or more from initial learned value, Intermittent loss of either camshaft or crankshaft position sensor, No crank reference signal detected during engine cranking
12 Direct battery input to PCM was disconnected within the last 50 key-on cycles
13 No change in MAP from start to run
14 MAP sensor voltage too low

Hope this helps. God bless

Apr 06, 2011 | 1991 Chrysler New Yorker

1 Answer

What does the 3-10 code mean for the 91 chrysler new yorker 3.3 litre


There is no 3-10 code for the 91 chrysler new yorker 3.3 Liter. Are you sure it is not blinking another code?

Fig. 1: Diagnostic trouble codes and descriptions - all vehicles 86724080.gif
Fig. 2: Diagnostic trouble codes and descriptions - all vehicles 86724081.gif

Dec 25, 2010 | 1991 Chrysler New Yorker

1 Answer

2000 Saturn SL2 wipers stop working


it could be the wiper relay or the wiper motor could be heating up and stoping causing it to work again when it cools down either case start with relay and if that does not fix the problem replase the wiper motor

Apr 15, 2010 | 2000 Saturn SL

1 Answer

Can't move wimdshield wiper arms on 91 ford ranger


Dis connect the transmission from the motor and turn the wiper motor on,then turn it off,when it stops,attach it to the transmission with the wipers in down(rest) position,then it will do right.

Apr 08, 2010 | 1991 Ford Ranger Supercab

1 Answer

I have had to re-install a windshield wiper motor in a 1981 Chrysler New Yorker. Upon completion the motor seems to either lock up or not be in the same sequence/rotation as the wiper arms. How can I get...


With the arms off, run the wiper motor and shut if off normally with the switch. After it stops install the arms in the parked position (horizontal with the lower edge of the windshield).

Oct 18, 2009 | Chrysler New Yorker Cars & Trucks

1 Answer

Wiper motor running, wipers stalled in vertical position during s


no you need a locking bolt to lock the wipers to the motor

Sep 01, 2009 | 1997 Chevrolet Cavalier

1 Answer

Windshield wipers


The fuse panel is under the instrument panel to the left of the steering column. Lift the handle to unlatch the panel and pull it down. The windshield wiper/washer system uses a circuit breaker in position #2 in the fuse panel. If your washer is working the circuit breaker is OK.

Jul 18, 2008 | 1991 Ford Taurus

Not finding what you are looking for?
1991 Chrysler New Yorker Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...