2007 Honda Accord Sedan Logo

Related Topics:

Anonymous Posted on Jul 03, 2008

Scratch Repair of Plastic Bumper

What product or methods can be used to repair/cover about a 4 inch long scratch in a plastic car bumper that is about 1/16 deep ? thanks

  • Anonymous Oct 01, 2008

    The garage door scratch my front plastic bumper. It's about 4 inch long, 3/8 wide and 1/8 deep. What method should i use. professional dodyshop might be too expensive.

    S.P.

×

5 Related Answers

Anonymous

  • 405 Answers
  • Posted on Dec 26, 2008

SOURCE: 1999 Accord front bumper cover

I do this for a living and I think I can help you.
The bumpers are available for around 35.00 wholesale, the paint is waht is expensive, Installation is a breeze. Bolts on each side and clips to wheel skirts, Headlights may need to be removed I can't remember, also under the car is a shield that attaches to the cover. It will come right off after that. I think a couple of clips under the hood holding it to the core support, I do so many of these it is hard to remember exactly how each one is attached, but just installed one on and acura rsx,. Hope this helps you!

Ad
Fleetw00d

Fleetw00d

  • 31 Answers
  • Posted on Jan 26, 2009

SOURCE: Bumper cover removal

It is a little more complicated than that. There are two nuts below the headlight assemblies in the engine compartment. You will need to remove the battery and overflow bottle to get at the one on the passenger side. Remove the turn signals in the bumper, then there are 2 or 3 bolts holding a mounting bracket behind the each of the turn signals. There are a number of bolts with washer heads and reatiners on the underside of the bumper as the previous responder indicated.

Anonymous

  • 1 Answer
  • Posted on Feb 12, 2009

SOURCE: cost to fix scratch

take some tooth paste and rub the scratch , many time this will repair if it's not too deep .

Anonymous

  • 6 Answers
  • Posted on Jul 03, 2009

SOURCE: 2005 Honda Accord Front Bumper cover replacement

easy there is a screw on both sides were bumper and fender meet just pop back fender liner its a phillips head. Then pop hood remove clips on black trim infont of radiator. Underside where bumper goes under car remove those clips and 10mm bolts after all is removed bumper just pulls off ...... may have to give it a hard **** a few times but it will come off. Should only take 15-20min to remove if its your first time

Molson02536

Harvey N Tawatao

  • 3854 Answers
  • Posted on Aug 09, 2009

SOURCE: the plastic bumper covers are dented

If the bumper cover is just dented and there is no rips or any other damages other then paint damage. You can use a heat gun and remould the bumper back in to shape. If there is a few cracks or break, you could also buy a bumper repair kit to repair the cracks and then just repaint the bumper. This should save you more money then the salvage yard bumper. Good luck and hope this helps. 

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How to replace 2008 Kia Sedona rear bumper cover

2008 Kia Sedona Bumper Covers

CarParts.com https://www.carparts.com > ... > 2008 > Bumper Cover

Get the best deals on an aftermarket 2008 Kia Sedona Bumper Cover. Lifetime Replacement Guarantee. Free 60-Day Returns. Order today!
"); background-repeat: repeat-x; display: inline-block; overflow: hidden; position: relative; background-size: 14px 11.4px; height: 11.4px; width: 68px;">"); background-repeat: repeat-x; display: block; background-size: 14px 11.4px; height: 11.4px; width: 70px;"> Rating: 4.8 · ‎10 votes · ‎US$101.99 to US$139.99

NEW Rear Bumper Cover for 2006-2014 Kia Sedona ...

Bumpers That Deliver https://bumpersthatdeliver.com > new-rear-bumper-co...

This replacement Rear Bumper Cover will help restore your vehicle's aesthetic value if you need to replace a scratched, dinged, or collision-damaged Rear Bumper ...
US$240.99

Rear Bumper Cover Repair procedures

Kia Sedona manuals https://www.kisedona.com > rear_bumper_cover_repa...

Take care not to bend or scratch the trim and panels. 1. Remove the rear combination lamp cover (A) using a screwdriver or remover.
0helpful
1answer

How do I repair a dent in the rear bumper of my 2004 Honda pilot? Do I have to remove the bumper and if so how is that done?

depending if its plastic you can remove the dent using a heat gun and a tap around the bump usually pop out. removing the bumper there are screws on the sides behind the wheel arch covers and 4 bolts around 1 foot away from the corners, if your model has sensors in the bumper they will need to be discounted. also any other wires that are they before you pull off the bumper.
0helpful
1answer

The rear bumper cover came off how can I reinstall it

2000 Toyota Sienna rear Bumper cover replacement (1998 ...

? 3:40
https://www.youtube.com/watch?v=AY1BBdg3q74
Sep 20, 2013 - Uploaded by SergSpace
2000 Toyota Sienna rear Bumper cover replacement (1998-2003) .... Automotive Bumper Repair Specialist- How to repairyour plastic bumper cover ... Toyota Sienna Rear Shock Installation 2003, 2004, 2005, 2006 - Duration: ... 2015 Toyota Sienna XLE - Duration: 28:13. by MikesCarInfo 35,234 views.

Fixing My Mom's Prius: Loose Rear Bumper Cover - YouTube




0helpful
2answers

How do I repair a plastic bumper?

these bumpers are hard to repair, most places replace the bumpers because of the problems trying to repair them. you can try a body shop that specializes in fiberglass corvettes they might have the best method.
4helpful
1answer

How to replace the rear bumper cover on a Chrysler Pacifica

1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.
0helpful
1answer

I have a holden senator new model 2009, a car slightly.

Depending on how deep the scratches are, you may be able to keep the bumper. You can probably sand, bondo, prime and paint the bumper and be ok. If you choose to replace, after market bumper covers start and around $70 usd and OEM bumpers start at $250 usd. Good Luck I hope you find this very helpful!
3helpful
1answer

I neede to remove the headlights for my 2008 E 350 and need instructions. OIt appears that removing the front bumper is needed ? Thanks

Here's some instructions for removing bumper and headlights.

E-Class W211 front bumper removal (standard body style).

Tools needed:
- Automotive wheel ramps (Rhino ramps from Autozone).
- 1/4" drive socket set with 8mm and 10mm sockets.
- #20 torx bit.
- Floor jack, optional but useful.
- Flat blade screwdriver.

Instructions for bumper removal:

1) Turn front wheels full right to remove push-pin fastener at lower front corner of left wheel well plastic splash guard. It's difficult to remove this fastener once the car is up on the wheel ramps.

2) Turn front wheels full left to remove push-pin fastener at lower front corner of right wheel well plastic splash guard.

3) Drive car up on wheel ramps. Block rear tires. Open hood.

4) Remove lower mesh plastic grille. There are five attachment points on the top edge of the grille. You can get to three of them with your hand by reaching between the radiator and the back side of the grille. The two outer ones can be released with a screwdriver also reaching in between the grille and radiator. Once the plastic tabs are released, you can remove the grille by pulling it out from the front of the car.

5) Remove the plastic panel located immediately behind the bumper from the bottom of the engine compartment. This panel is held in place with nine sheet metal screws with a 8mm hex head. Five screws are on the bottom of the car and there are two screws in each wheel well at the inner lower edge. After removing all nine screws you can work the panel free.

6) Disconnect the cable from each fog light and remove both fog lights. They are held in place by two sheet metal screws with a #20 torx head.

7) Remove the side marker bulbs. The one on the passenger side turns clockwise to remove and the one on the driver side turns counter-clockwise.

8) Remove the temperature sensor from its socket on the driver side.

9) If you have a floor jack, raise the car at the jack point on the cross member below the engine. You do not want to raise it off the wheel ramps. But it helps to have more clearance above the tires to work in the front wheel wells.

10) Remove three of the plastic nuts holding the forward half of the plastic wheel well liner in place. It's not necessary to remove the plastic liner. You just need to loosen it up so that you can pull it away from the fender to gain access to the screw and bracket securing the bumper to the fender.

11) Pull back the wheel well liner and remove the sheet metal screw from the rear end of the metal bracket . There is only one sheet metal screw (#20 torx head) holding this bracket in place. Don't attempt to remove the bracket yet. I used a #20 torx bit in a 1/4" socket with a 6-inch extension for a 1/4" drive wrench. The head of the screw faces the ground.

12) Remove the 5mm bolts (8mm hex head) holding the bumper to the headlight assembly between the small lens and large lens (both sides).

13) Remove the two 6mm bolts (10mm hex head) on either side of the large grille area opening.

14) Remove the two 6mm bolts (10mm hex head) securing the bumper to the bottom edge of the crashbar. You can access these bolts through the front where you removed the plastic mesh grille.

15) Remove the three 5mm bolts (8mm hex head) holding each headlight assembly in place. Two longer bolts are on top. One at the rear outer corner and one at the front inner corner. The third bolt is accessed from the bottom. It's in the area above the fog lamps. You don't need to disconnect the headlight cables and remove the assembly. But it helps to allow the headlight assembly to "float" freely while you disengage the bumper from the fender.

16) At this point all of the fasteners holding the bumper in place have been removed. The only thing left to do is to remove the two brackets "clamping" the bumper cover to the lower front edge of the front fenders. Before you do this, position some cardboard boxes, bags of packing material, six packs of paper towels, or other suitable items to protect the bumper in case it falls off the car.

17) The bracket holding the bumper cover to the fender has a "pin" that slips into a slot at the front edge of the bumper cover. There is a matching slot near the front edge of the fender. It's not possible to see this pin from the bottom of the car. Use a flat blade screwdriver to pry the bracket away from the bumper/fender and towards the center of the car. The bracket will "hinge" on the pin at the front end of the bracket. After you swing the bracket away from the bumper, you need to slide it forward to remove it from the slot in the bumper cover and fender. You will probably scratch some paint off of this bracket with the screwdriver. I recommend repainting the scratched areas of the bracket before reinstalling it.

18) After removing the bracket from each side of the car you need to deal with the small plastic "hook" holding the bumper cover to the very front tip of the fender. This hook is an integral part of the bumper cover. Disengaging this hook from the fender is probably the most difficult step of removing the bumper. Simultaneously raise the head light assembly slightly, push the leading edge of the fender outward slightly, and push the bumper cover inward toward the headlight assembly. Don't get too aggressive with the fender. It's aluminum and you will make a real mess if you apply too much pressure on the fender. It took me about 20 minutes to free each side from this hook. It should take you less time, since you now know that the hook exists!

19) Gently pull the bumper forward and away from the car. This is one step where a second person would be helpful. But I did manage to do this step alone. There is a "pulley" like attachment point on each side just below the fender/bumper seam.

To re-install the bumper, reverse the order of the steps above. When re-installing the bracket between the bumper cover and fender, I smeared a thin coating of car wash soap on the bracket to facilitate snapping the bracket back into place.




0helpful
1answer

How to clean up white spot of black bumper CRV ?

There are a couple after-market products for do-it-yourselfers for repairing minor bumps, discolorations, dents, and the likes.
If your white spots got there as a result of a scratch from another car with white body color, you could find some chemical-based product to clean it out.
However, most of these plastic/vinyl bumpers are all made black by the manufactures. And they are supposed to be repainted in colors exactly matching the concerned vehicle.
Visit a reputable autoparts store, and look in the 'body section'. You should find 'spot/scratch remover' in about two different quantities. If unable to locate this in the store, ask for assistance.




1helpful
1answer

How do I remove the back bumper (plastic) on a 2003 toyota camry?

you can heat the bumper heat gun ( you can rent one i think?)
this will soft the bumper so you push it out easily on the car

1. inside your trunk remove small back clips in trim panel
2. remove tail lamp four 8mm nut perside unplug wires
3. remove black clips under tail lamps ( flat head screwdriver to pull center of the clip up slowly then remove the hole clip)
4. three if the some clips are bottom if the bumper
5. three or four 10mm nuts in side the quarter panel on the right and left side
6.four s shape clips are top bumper that will pull loose
7. with some help slide bumper by pulling it off it
8. when you reinstall the bumper you may need to tape the strophe reinforcement in place
0helpful
1answer

Cost to fix scratch

take some tooth paste and rub the scratch , many time this will repair if it's not too deep .
Not finding what you are looking for?

630 views

Ask a Question

Usually answered in minutes!

Top Honda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...