Question about 1989 Ford F 250

1 Answer

1989 ford Van passenger side power window will not raise or lower. Glass is intact, in bottom support arm, and in tracts. Motor makes sound like it is raising or lowering window but window does not move.

Posted by on

  • Anonymous Mar 30, 2014

    THE PASSENGER SIDE POWER WILDOW WILL NOT LOWER OR RAISE

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 702 Answers

The problem is the power motor gear that raises and lowers the window is worn out. The motor runs, but the gear cannot engage with the gear on the window regulator.

Posted on Jul 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the power window relay located in a 2002 mercury villager?


Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Visual Inspection Chart Mechanical Electrical
  • Improperly aligned window
  • Damaged window mounting
  • Window frame interference
  • Central junction box (CJB) Fuses:
    • F30 (10A)
    • F32 (20A)
    • F34 (20A)
    • F59 (7.5A)
  • Battery junction box (BJB) Fuses:
    • F20 (30A)
    • F27 (45A)
  • Switches
  • Circuits
  • Connectors
  • Heated back light
  • Relays
Which window is not working ?
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .

Apr 07, 2015 | 2002 Mercury Villager

1 Answer

Drivers side window will not roll up,passenger side works just fine there no clicking sound when you try to raise drivers side,fuses are ok


In certain Ford cars (you didn't say WHICH Ford vehicle you have), the motor that drives the power window has a plastic nut in it that facilitates the movement of the glass. Over time, this plastic nut will wear away and eventually won't turn the regulator (which makes the glass move up and down on its track). You can remove the motor, open up the casing of the motor, put in a metal nut and it will work again. I forgot the size of the nut, but they are common and can be found in a parts store for less than a dollar.

Mar 13, 2011 | Ford Windstar Cars & Trucks

1 Answer

How do I realign the passenger side window?


WINDOW GLASS REMOVAL

NOTE: Window glass must be operable in order to remove door assembly carrier. Any malfunction that prevents the window (manual or power) from being lowered must be corrected before proceeding.

  • Remove door trim panel.
  • Pry out sealing plugs in door assembly carrier to gain access to window glass securing bolts.
  • Lower window until window glass securing bolts are accessible.
NOTE:
If the power window motor is not working it can be renmoved to allow the window to be slid down.

  • Loosen window glass securing bolts and carefully press glass securing clamps apart.
NOTE:
If glass is being replaced due to breakage, remove door assembly carrier and remove broken shards of glass to prevent rattling noises in door.

  • Carefully lower the window regulator.
  • Lift window glass up and pivot forward, starting at the taller end of the glass. Pivot forward towards the direction of the side mirror.
  • Place removed window glass in a secure location.
WINDOW GLASS INSTALLATION

  • Slide forward part of window glass into opening and pivot glass downward, reversing the removal proceedure.
  • Raise window regulator until window glass securing bolts are visible in access holes on door assembly carrier.
  • Gently press window in the direction of the door latch or highest part of glass and tighten securing clamp bolts.
  • Remainder of installation is the reverse of disassembly.
  • Check operation of window before final installation of door trim panel.
TIGHTENING TORQUE
Window glass securing bolts...........10Nm (89in-lb)

Jun 25, 2010 | 2000 Volkswagen Beetle

1 Answer

Power window not functioning on F-250 Super cab Year 1989


check it with a test light one side should supply power down and the other for up. if you have power for up and down then youll need a motor

Sep 07, 2009 | 1989 Ford F 250

1 Answer

How to install a rear window regulator on a 2000 Oldsmobile Intrigue


How do you remove door panels and replace window regulator on an Intrigue? Answer : For a 2002 Intrigue – Front Passenger I didn’t disconnect battery. You use window switch later to align window tabs to regulator frame – with ignition off power locks work, nothing is exposed.
1. Remove visible screw under armrest, pop out finger inset oval panel, remove exposed 2nd screw. 2. Pop off door handle trim – lock button assembly slide thru its hole in door panel. 3. Pop off window switch trim/holder – slide thru its hole in door panel. 4. Remove 2 slot screws under bottom of door.
5. I used a smooth metal letter opener (or old fork) to pry panel from door at each point plastic fasteners insert into metal. Start prying a little, see three on bottom perimeter two inches from edge. Three on door open edge and three on door hinge edge. Slow and easy = whole panel will pop off. A metal compression spring fastener connects at top door hinge edge trim – pry out. Be sure door lock and window switch remain inside. Clean all surfaces of door panel and lay on back seat.
6. With panel off you see clear plastic moisture sheet stuck to door with black rubbery paste - peel it from door for reattachment. You now see mechanism and fastener points. Lay out replacement window regulator and motor on mat by door to help you recognize fastening points, etc.
7. Carefully pull glass all way up and hold in place with two pieces duck tape two feet long with ¼# removal tabovers. Put a foot on outside glass and loop over door frame a foot to inside glass – with room to later redo when you twice lower and raise a foot to access bolts removing/attaching it to regulator bar.
8. Remove 3 bolts holding motor to door. 9. Remove upper 2 bolts and lower 2 bolts holding regulator frame to door.
10. Lower window to expose thru panel cutout area two bolts holding glass tabs to regulator, retape securely. Remove bolts, raise window, retape securely by looping over door frame.
11. Window regulator and motor assembly comes out as unit. Unplug window switch tab to release from motor. BEFORE reassembly clean the inside of the door, put in a little Borax for bugs, etc.
12. Reassemble by starting three motor bolts, fitting regulator assembly in door cavity. Replug window switch, motor can be placed in thru oval slots, leave all bolts loose. Replace two upper and two lower regulator bracket bolts, leave loose.
13. Turn on ignition, use window switch to lower window glass regulator tab bracket until accessible thru panel cutout. Turn off ignition, manually lower glass until tabs align with regulator bracket bolt holes and tighten these bolts. Take tape off, turn on ignition, raise window to top.
14. Tighten three motor bolts and four regulator bracket bolts, make sure alignment is OK. Remove your tape residue - clean goo from both glass sides with Goof Off. THEN raise and lower several times to assure all fits and works like new.
15. Reinstall clear plastic sheet, aligning any fastener holes and rubbing down perimeter with a cloth .
16. Align door panel, assure door lock and window switch are pulled thru. Visually align each tab on door opening side and pop them in one at a time. Continue on bottom – make sure you see them align or they will break. Finish on door hinge side and with metal fastener at top. IF you break a fastener, take one from small bag you bought from Pep boys - otherwise take bag back for refund…
17. Reinstall 2 armrest screws and 2 bottom panel screws, then pop in door lock, trim piece and window switch.
Clean the window inside and out with glass cleaner/polish/raineze so it will slide easily and your done. You can’t do anything about the motors going out. You can avoid regulator tab breaks by making sure the window is raised BEFORE closing those big doors – down is the weak moment!! I work slow and clean as I go, the job took two hours. I highly recommend partsgeek.com – saved a bundle over dealer and they shipped everything in several days – as ordered!

Jul 27, 2009 | 2000 Oldsmobile Intrigue

1 Answer

Rear side windows


This may be just a case of inadvertently hitting the window lock out n th driver door window switch by mistake. Check that first. Here's some background on window operation

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Symptom Chart Condition Possible Sources Action
  • All windows are inoperative
  • BJB Fuse:
    • F20.
  • Circuit.
  • Power window relay.
  • Front door power window switch.
  • GO to Pinpoint Test A .
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .
  • Vent power window is inoperative — quarter window glass power latch
  • Circuit.
  • Quarter window glass switch.
  • Quarter window glass power latch.
  • GO to Pinpoint Test C .
  • The one touch down feature is inoperative
  • Master window regulator and door lock switch.
  • INSTALL a new master window/door lock/unlock switch. REFER to Switch—Master Window Door Lock/Unlock .
  • The back window will not defrost
  • CJB Fuses:
    • F30 (10A).
    • F32 (20A).
    • F34 (20A).
  • BJB Fuse:
    • F27 (45A)
  • Circuit.
  • Heated back window switch.
  • SEC/timer module.
  • Rear window defrost relay.
  • GO to Pinpoint Test D .
  • The back window defrost will not shut off automatically
  • SEC/timer module.
  • Circuit.
  • Rear window defrost relay.
  • GO to Pinpoint Test E .

Jan 28, 2009 | 1999 Mercury Villager

1 Answer

1995 G20 van


the actual power window motor is getting old and probably needs replacement. as they age they get slower and picky about which way they want to go, outside temp also affects the operation also. in warmer weather they tend to work better

Aug 07, 2008 | 1995 Chevrolet G20

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

227 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...