Question about Renault R18

2 Answers

Imobilizer code I have a code to reset my imobilzer, but have no idea how to do it. I broke down about a year ago and called Renult to come and fixed the problem, which they did , the engineer gave me the code and did tell me at the time how to do it, if this happened again but i have forgotten, Can you help

Posted by on

2 Answers

Dear, sir/mdme Clé Hadrumet is a society in Tunisia, and in Sousse exactly, with years of experience in the business of keys and the electronic technology of keys. the Purpose of the society is to guarantee the performance of these products with the best possible quality to satisfy the need of the market. We sell auto diagnostic, key programming and pin code reading software and hardware. We also offer full range of key blanks and transponder key blanks, key cutting machines, locks and cylinder locks, autolocks, wide variety of locksmiths tools and accessories to any Locksmiths companies.

Remote keys Transponder keys Key Programmer Auto programmer Diagnostic tools for all models Contact us Take a look : Regards, Clé Hadrumet

Posted on Jul 25, 2008

  • Level 1:

    An expert who has achieved level 1.


    An expert that gotĀ 5 achievements.


    Visited the website for 3 consecutive days.


    An expert that hasĀ over 10 points.

  • Contributor
  • 18 Answers

Try this. Turn the ignition on and allow the immobilizer to arm. Turn ignition off and count number of flashes required for first number of PIN.(eg 6) then turn ignition on. Turn off and count number of flashes for next number in PIN. Repeat till all numbers of PIN sequence have been used, then start car immediately. If you make an error, come back in a few minutes and start again.
Good luck.

Posted on Jul 04, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1996 honda 160i luxline remote imobilzer programing

reset immobiliser I HAVE A HONDA CIVIC 1.6 LUXLINE ...
Jan 22, 2014 - reset immobiliser I HAVE A HONDA CIVIC 1.6 LUXLINE 1998. I NEED TO BYPASS THE IMMOBILSER TO START THE CAR WITHOUT IT ... Press any button on remote one time within 20 seconds. .... How can i fix my honda 160i luxline92 model starting difficulty? Jul 20 ... Jun 09, 2012 ' 1996 Honda Civic.

Sep 27, 2015 | Honda Cars & Trucks

1 Answer

Car got broke in to on drivers door now 1996e320 wont start

the drivers side door is the main door for the imobilizer to work if its been tamperd with the car will not start untill its been reset on a computer hope this helps ivan

Oct 05, 2012 | 1996 Mercedes-Benz E-Class

1 Answer

Check engine light stays on. changed oxygen sensor, pcv valve, coolant sensor, switched out PROM chip, and cannot get a code to blink. replaced all hoses coming off carb. smog pump and egr valve been...

what you could start with is checking to see what trouble codes are being logged for this vehicle...if the engine light stays on, it means the ecu is registering a the means of a trouble the trouble code doesnt tell you how to fix it, but it does give you the direction to go down...judst wondering if you have tried to obtain the trouble codes

Aug 26, 2010 | 1981 Chevrolet Corvette

1 Answer

97 jeep cherokee cuts out when you step on the gas. after a while it will not run at all. after it cools down it will start right up. Any ideas??

After spending Hundreds of $ and hours on trying to figure this out we finally broke down and went to the scrap yard and got a PCM for this car. It only cost about $30. Wish we would have done this a year ago!!!!

Aug 21, 2010 | 1997 Jeep Grand Cherokee

1 Answer

Ok i have a renult espace 02 that is a dvla repossesion and i have no keys. i took my logbook and £280 to renult and thay suppiyed me with keys (that dont fit) and wont give me a refund, is there...

typical of renult that is,,,the french never did like us!
i would take the kyes back to the renult dealer and in no unserten way tell them the goods they sold you "were not fit for the purpose" and you demand your money back or they get you the right kyes that fit your car,, and pronto at that!
"""its all coverd in the sale of goods act""",and it sounds like you got them by the n*ts on this one
if you can try to get the car down to the dealer or call the "AA" or "RAC" out to do this for you,,,or you could get a lock smith to get the kye barrel out that way you will have the kye number on it or the lock smith could reset the lock to take your kye,,,
bit pricy this way,,,best thing is get the right kyes

Nov 05, 2009 | 2003 Renault 181

1 Answer


if you turned the key with the ignition with the imobilizer, you now have to get the right ignition and a new PCM because the PCM now thinks the car has SKIM (imobilizer)

Jun 24, 2009 | 2000 Dodge Neon

1 Answer

Renult megane electric roof problem

has to be reset on ECU its a renault so it encrypted software .dealer only hope you can lay the golden egg for them

Nov 01, 2008 | 2000 Renault 181

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

497 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

xxxxxx xxx

Level 3 Expert

4823 Answers


Level 3 Expert

71338 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides